Modular Closets SHELF TOWER UNIT Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
SHELF TOWER UNIT
1-844-969-4247 suppor[email protected]

ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
PARTS LIST
BOX 1
BOX 4 - Leg Extension Kit (Optional)
BOX 2
BOX 3
1A
E
JAdjustable Shelf (Qty 2 or 4) Shelf Pins (Qty 8 or 16)
C
D
H
I
L
Rear Hanging Cleat (Qty 3)
Set Shelf (Qty 3)
Cam Post (Qty 18)
Camlock (Qty 18)
Screw, Square Drive, 2.5" (Qty 6)
A
BLeft Side Panel (Qty 1) Right Side Panel (Qty 1)
H
J
I
L
A B
E
D
C
F G
FINISHED EDGE
FINISHED EDGE
FINISHED EDGE
FRONT
FRONT
FRONT FRONT
CFINISHED EDGE C
F
G
H
I
K
Rear Hanging Cleat (Qty 1)
Left Leg Extension (Qty 1)
Right Leg Extension (Qty 1)
Cam Post (Qty 2)
Camlock (Qty 2)
Wood Dowels (Qty 4)
GJ H

2
2.1 Install one Cam Post (H) into each of the nine holes on Left Side Panel (A) and Right Side Panel (B). Tighten until
Cam Posts are seated against Side Panels.
A
TOP
B
H
H
H
H
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
1B Level
Stud Finder Drill, 3/32" bit size Phillips Screwdriver
TOOLS REQUIRED
(not included unless noted)
1.1
1.2
Lay parts out on a protective surface to prevent damage.
Tip: Spread out the cardboard packaging to use as a protective
surface.
Inventory parts against the Parts List. Make sure all parts are
present before proceeding.
Drill Bit, Square, #2

3
D
B
H
H
H
C
D
D
C
C
3.1 Assemble Set Shelves (D) and Rear Hanging Cleats (C) onto Right Side Panel (B) by sliding the Shelves and
Cleats onto the Cam Posts (H) on Side Panel. BE SURE wood dowels in Shelves and Cleats engage drilled
holes in Side Panel, and all parts are pressed flush against Side Panel.
IMPORTANT NOTES
Install Set Shelves (D) with finished edges facing forward (toward front of unit).
Install Rear Hanging Cleats (C) with holes for Cam Locks facing the rear of the unit and the unfinished edge against
the Set Shelf (D).
Install upper Set Shelf (D) with holes for Cam Locks facing the top of the unit.
Install middle and lower Set Shelves (D) with holes for Cam Locks facing the bottom of the unit.
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
TOP

4
4.1 Install Left Side Panel (A) onto assembled Set Shelves (D) and Rear Hanging Cleats (C). BE SURE
Wood Dowels in Shelves and Cleats engage drilled holes in Side Panel, and Side Panel is pressed flush against
Set Shelves and Cleats.
C
D
C
D
C
A
B
D
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
TOP

5
I
D
D
C
C
C
D
5.1
5.2
Insert Camlocks (I) in holes in Set Shelves (D) and Rear Hanging Cleats (C), with arrow pointing toward Cam
Post opening. Be sure Camlocks engage Cam Posts, and are fully seated in Shelves and Cleats.
Tighten Camlocks (I) clockwise to lock.
I
ARROW TOWARD
CAM POST OPENING
II
I
I
I
I
I
II
TOP
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT

6
H
F
G
C
K
K
I
ARROW TOWARD
CAM POST OPENING
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
FOR LEG EXTENSION KIT INSTALLATIONS ONLY
Leg Extension Kit purchased separately)
6.1
6.2
6.3
6.4
6.5
Insert four Wood Dowels (K) into holes in edges of Left Leg
Extension (F) and Right Leg Extension (G).
Install one Cam Post (H) each into Left Leg Extension (F)
and Right Leg Extension (G). Tighten until Cam Posts are
seated against Leg Extensions.
Assemble Left Leg Extension (F) and Right Leg Extension
(G) onto Rear Hanging Cleat (C) by sliding the Cam Posts (H)
into Cleat. BE SURE wood dowels in Cleat engage drilled
holes in Leg Extensions, and all parts are pressed flush against
each other.
Insert Camlocks (I) in holes in Rear Hanging Cleat (C),
with arrow pointing toward Cam Post opening. BE SURE
Camlocks engage Cam Posts, and are fully seated in Cleat.
Tighten Camlocks (I) clockwise to lock.
Align Wood Dowels (K) in assembled Leg Extensions with
holes in Shelf Tower, and press Tower and Leg Extensions
together.

7
INSTALLATION
7.1
7.2
7.3
Determine the mounting location for the unit. The unit can be installed with or withou the optional Leg Extension Kit
(purchased separately) as shown in step 6.
Using a stud finder, locate studs to which the unit will be secured. Mark stud locations with a pencil.
With the unit positioned at the desired location, level the unit, then drill pilot holes through Rear Hanging Cleats (C),
NOTE: For 18" and 24" units, it is likely that only one stud will pass through the unit. In these cases, use two screws
through each Rear Hanging Cleat.
WITH LEG
EXTENSION KIT WITHOUT LEG EXTENSION KIT
12" FROM
FLOOR
STUDS
PILOT
HOLES
PILOT
HOLES
PILOT
HOLES
PILOT
HOLES
C
C
C
C
C
C
C
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT

8
8.1 Secure Rear Hanging Cleats (C) to
studs using 2.5" Screws (L). Tighten
Screws using Square Drill Bit
(provided) and Drill.
C
L
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT

9
9.1
9.2
For each Adjustable Shelf (E), insert four Shelf Pins (J) into pin holes inside the Tower at the desired height.
Rest Adjustable Shelves (E) on Shelf Pins (J).
E
E
J
J
J
J
J
J
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHELF TOWER UNIT
JJ