modway EEI-2650 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
EEI-2650 TABLE
Hardware:
Component:
A Bolt M8x35mm x2
B
1 Table Top x1
Thank you for purchasing the MODWAY TABLE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
2 Table Leg x2
D
1
2
4
3 Top Rail x1
Allen Wrench M5 x1
Flat Washer M8 x11
C
Bolt M8x50mm x9
2
3
6
6
5
5
4 Bottom Rail x1 5 Support Rail x4 6 Leaf x2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
EEI-2650 TABLE
STEP 1:
Ax2 Bx2 Dx1 Cx4 Hardware & Tool required
STEP 2:
Please put Table Legs (2), Top Rail (3) and Bottom Rail (4) upside down on a carpeted or padded area.
Position Bottom Rail (3) and Top Rail (3) to the bottom of Post (3) as shown.
Insert 2 pieces of Bolt (B) with 2 pieces of Flat Washer (C) into the pre-drilled holes on Table legs (2) through the pre-drilled
holes on Top Rail(3).
Insert 2 pieces of Bolt (A) with 2 pieces of Flat Washer (C) into the pre-drilled holes on Bottom Rail (4) through the pre-drilled
holes on Table Leg (3).
Use Allen Wrench (D) to tighten Bolts (A&B) clockwise until secure.
Bx7 Cx7 Dx1 Hardware & Tool required
1
Please put Table Top (1) upside down on a carpeted or padded area.
Position the assembled Table Legs(2), Top Rail (3), Bottom Rail (4) and Support Rails (5) to Table Top (1) as shown.
Insert 4 pieces of Bolt (B) with 4 pieces of Flat Washer (B) into the pre-drilled holes on Table Top (1) through the
pre-drilled holes on Table Leg (2).
Insert 3 pieces of Bolt (B) with 3 pieces of Flat Washer (B) into the pre-drilled holes on Table Top (1) through the
pre-drilled holes on Top Rail (3).
Use Allen Wrench (D) to tighten all Bolts (B) clockwise until secure.
2
A
2
3
4
C C
A
B
D
C
2
5
5
5
3
4
2
C
B
C B
C
B
C
D
C
B
D
5
Remove the pre-installed Bolts from each piece of
Support Rail (5).
B

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
EEI-2650 TABLE
STEP 3:
STEP 4:
Assembly is complete. Your table is ready to be used now!
Position the assembled table to the location your desire.
1
Carefully turn over the assembled table.
If your want to use Leafs (6), please fully extend Support Rails (5) and put Leafs (6) to Support Rails (5) as shown.
Insert the removed 4 pieces of Bolts from step 2 into the pre-drilled holes on bottom of Table Top (1) through the pre-drilled
holes on bottom of Support Rail (5).
Use Allen Wrench (D) to tighten the removed Bolts from step 2 clockwise until secure.
6
6
2
2
3
5
5
5
Dx1 Hardware & Tool required
Removed Bolts from Step 2
4
D