Moeller Teleservice XC100 Quick guide

Moeller GmbH
Industrieautomation
Hein-Moeller-Straße 7–11
D-53115 Bonn
E-Mail: [e-mail]
Internet: www.moeller.net
© 2002 by Moeller GmbH
Subject to alteration
AWB2724-1490GB xx/xx/Ki 07/04
Printed in the Federal Republic of Germany (0x/02)
Article No.: xxxxxx
AA
Think future. Switch to green. Think future. Switch to green.
SystemsIndustrial Automation
Hardware, Engineering, Configuration
07/04 AWB2724-1490GB
Teleservice
XC100
Building Automation

All brand and product names are trademarks or registered
trademarks of the owner concerned.
1st published 2003, edition date 04/03
2nd published 2004, edition date 07/04
See revision protocol in the “About this manual“ chapter
© Moeller GmbH, 53105 Bonn
Author: Werner Albrecht
Editor: Thomas Kracht
Translator: David Long
All rights reserved, including those of the translation.
No part of this manual may be reproduced in any form
(printed, photocopy, microfilm or any other process) or processed,
duplicated or distributed by means of electronic systems without
written permission of Moeller GmbH, Bonn.
Subject to alteration without notice.

I
Before commencing the installation
• Disconnect the power supply of the device.
• Ensure that devices cannot be accidentally
restarted.
• Verify isolation from the supply.
• Earth and short circuit.
• Cover or enclose neighbouring units that
are live.
• Follow the engineering instructions (A A)
of the device concerned.
• Only suitably qualified personnel in
accordance with EN 50110-1/-2
(VDE 0105 Part 100) may work on this
device/system.
• Before installation and before touching
the device ensure that you are free of
electrostatic charge.
• The functional earth (FE) must be
connected to the protective earth (PE) or
to the potential equalisation. The system
installer is responsible for implementing
this connection.
• Connecting cables and signal lines should
be installed so that inductive or capacitive
interference does not impair the
automation functions.
• Install automation devices and related
operating elements in such a way that they
are well protected against unintentional
operation.
• Suitable safety hardware and software
measures should be implemented for the
I/O interface so that a line or wire breakage
on the signal side does not result in
undefined states in the automation
devices.
• Ensure a reliable electrical isolation of the
low voltage for the 24 volt supply. Only
use power supply units complying with
IEC 60364-4-41 (VDE 0100 Part 410) or
HD 384.4.41 S2.
• Deviations of the mains voltage from the
rated value must not exceed the tolerance
limits given in the specifications, otherwise
this may cause malfunction and dangerous
operation.
• Emergency stop devices complying with
IEC/EN 60204-1 must be effective in all
operating modes of the automation
devices. Unlatching the emergency-stop
devices must not cause restart.
• Devices that are designed for mounting in
housings or control cabinets must only be
operated and controlled after they have
been installed with the housing closed.
Desktop or portable units must only be
operated and controlled in enclosed
housings.
Moeller GmbH Safety instructions
Warning!
Dangerous electrical voltage!

II
• Measures should be taken to ensure the
proper restart of programs interrupted
after a voltage dip or failure. This should
not cause dangerous operating states even
for a short time. If necessary, emergency-
stop devices should be implemented.
• herever faults in the automation system
may cause damage to persons or property,
external measures must be implemented to
ensure a safe operating state in the event
of a fault or malfunction (for example, by
means of separate limit switches,
mechanical interlocks etc.).

07/04 AWB2724-1490GB
1
Contents
About this manual 3
List of revisions 3
Structure 3
Abbreviations and symbols 3
Further documentation 3
1 General 5
Range of applications 5
Hardware/Software requirements 5
2 XC100/X200 – PC Connection 7
Physical structure of the connection (overview) 7
Connection PC – modem or modem – XC100/XC200 7
Connection PC – TD32B modem 7
– Cable layout 7
Modem TD32B – XC100/XC200 connection 8
– Cable layout 8
Connection modem – modem 8
– Telecontrol cable connection 8
– Handshake lines 8
– Connection via 2-/4-wire leased line 9
– Connection via dial-up line 9
Modem settings 10
– Dial-up line 10
– Leased line 12
LED status indication 13
3 Programming 15
Modem connection via leased and dial-up lines 15
Connection between PC and control 16
ONLINE modification 16
Index 17

07/04 AWB2724-1490GB
2

07/04 AWB2724-1490GB
3
About this manual
List of revisions
The following are the main changes and amendments which have
been made since the last edition of this manual:
Structure
This manual describes the steps necessary for remote
programming of XC100/XC200. It describes the installation,
device configuration and parameter allocation of communication
components.
This manual does not replace the modem manufacturer's operator
manual. It is essential that you note and adhere to the modem
documentation.
This manual refers to the use of Type TD32B DC analog modem
from Messrs. Westermo. This modem is suitable for leased-line
and dial-up line connection.
Abbreviations and symbols
Symbols used in this manual have the following meanings:
XIndicates actions to be taken.
Select ‹File rNew› means: activate the instruction “New” in the
“File” menu.
For clarity of layout, we adhere to the following conventions in this
manual: at the top of left-hand pages you will find the Chapter
heading, at the top of right-hand pages the current Section
heading; exceptions are the first pages of Chapters and empty
pages at the end of Chapters.
Further documentation
• XSoft, Programming software (h1437g.pdf)
• XI/OC signal modules, Hardware and engineering (h1452g.pdf)
• XC-CPU101-..., Hardware, Engineering and Functional
Description (h1453g.pdf)
• XC-CPU201-..., Hardware, Engineering and Functional
Description (h1491g.pdf)
• Function blocks for XSoft (h1456g.pdf)
• Installation manual TD-32/485; TD32 (Messrs. Westermo)
6178-2303.
These manuals are available as online PDF files, with the exception
of the installation instruction from Messrs. Westermo which is
supplied on a CD.
The most current and up-to-date edition of the manual can also be
found under http://www.moeller.net/support: search term: e.g.
“AWB2725-1452G”.
Edition date Page Description Change
07/04 8 „Handshake lines“ j
10 „Modem settings“ j
15 „Programming“ j
Modem A modem is used for conversion of signals from a
data terminal into electrical signals and vice versa
Note!
Warns of a hazardous situation that could result in
damage to the product or components.
Caution!
Warns of the possibility of a hazardous situation that
could result in major damage and minor injury.
Warning!
Warns of the possibility of a hazardous situation that
could result in major damage and serious or fatal injury/
death.

07/04 AWB2724-1490GB
4

07/04 AWB2724-1490GB
5
1 General
Range of applications
The telecontrol service for XC100/XC200 is intended for use
wherever PC and XC100/XC200 controller are at different
locations, and the connection therefore has to be established via
analog modem and leased or dial-up line.
The telecontrol service enables user program download, ONLINE
modification and status indication in the RUN mode.
Hardware/Software requirements
•Hardware
– Programming PC
– XC-CPU101/201-...-8DI-6DO (-XV)
– Analog modem: TD32B
– Analog leased line or dial-up line.
•Software
– XSoft programming software.

07/04 AWB2724-1490GB
6

07/04 AWB2724-1490GB
7
2 XC100/X200 – PC Connection
Physical structure of the connection (overview)
The following diagram shows how the XC100/XC200 is connected
with the PC. No target telephone number needs to be entered for
leased-line connection. For dial-up line connection it is necessary
to enter the target telephone number in the communication
parameters.
Connection PC – modem or modem – XC100/XC200
Data transfer is asynchronous, handshake signals are not used. For
RS-232 communication you can use either the 9-pole terminal
block at the top edge of the modem or the 25-pole SUB-D plug on
the front of the modem.
In order to exclude as much interference as possible, we
recommend that you do not use ribbon cable. Screened cables
achieve satisfactory results in extremely noisy environments.
Connection PC – TD32B modem
Cable layout
figure 2 shows the necessary connection between the COM1 (2)
interface on the PC and the RS-232 interface on the modem. Since
handshake signals are not being used, a link is required between
terminals 2 and 6 on the terminal block at the top of the modem.
Figure 1: Connection structure for leased line and dial-up line
aPC with XSoft programming system; connect the RS-232
connection cable at the COM1 or COM2 interface.
bConnection via RS 232 C; see figure 2 for the cable layout
cTelephone modem: TD32B, from Messrs. Westermo;
e.g. Tel.-No.: 1471
dAnalog telecontrol connection via leased line or dial-up line.
eTelephone modem: TD32B, from Messrs. Westermo;
e.g. Tel.-No.: 1875
fConnection via RS232C; see figure 3 for cable layout
gXC100/XC200 automation system
g
ca
bd
e
f
Figure 2: Physical link between PC and modem
PC
COM1/2
TD-32B
RS 232
9-pin
SUB-D
plug
connector
Plug
Socket
25-pole
SUB-D
socket
connector
325
7
Terminal
block
SUB-D
socket
4
6
73
2
1
6
2
77
8
or
SG
DSR
Link RTS
RxD
TxD
F3 m
5
2
3
7
6
2
3
4

XC100/X200 – PC Connection 07/04 AWB2724-1490GB
8
Modem TD32B – XC100/XC200 connection
Cable layout
figure 3 shows the necessary connection between the RS-232
interface on the XC100/XC200 and the RS-232 interface on the
modem. This connection also does not use handshake signals.
Connection modem – modem
Telecontrol cable connection
The connection between the two modems is made via the public
and/or private telephone network. The TD32B modem is suitable
for use for a leased-line as well as for a dial-up line connection.
Connect the telecontrol cable to the 6-pin RJ-12 plug on the front
of the device or to the terminal block on the left at the bottom of
the modem, to the terminals marked TXD and RXD.
Handshake lines
Since handshake connections are not available on XC100/XC200,
please note the following:
The TD32B modem is set to hardware handshake with RTS – CTS
ex-works. As a handshake signal is not available with the XC100/
XC200, the signal will need to be simulated. The following
possibilities can be applied:
• Physically connect a send and receive modem to the terminals
6 (RTS) and 2 (DSR) (insert wire jumper).
• Deactivate the handshake with the AT&K0 command.
• Set DIP switch SW3-2 with the send and receive modem to ON.
The settings have the effect that the RTS input signal is evaluated
as a “High” signal. It is thus possible to set up a data transfer
circuit with the sole connection of TX, RX and GND.
Figure 3: Physical link between modem and XC100/XC200
TD-32B
RS 232
XC100/
XC200
RS 232
25-pole SUB-D
socket connector
Plug
Socket
8-pin
plug connector
7
6
2
3
4
4
7SG
DSR Link
RTS
RxD
TxD
F3 m
Terminal
block
SUB-D
socket
4
6
73
2
1
6
2
77
8
8
5
or
8
7
6
5
4
3
2
1
Figure 4: Link DSR – RTS
SG
DSR Link
RTS
RxD
TxD
Terminal
1
6
2
77
8

07/04 AWB2724-1490GB Connection modem – modem
9
Connection via 2-/4-wire leased line
The following diagrams show the telecontrol connection via the
terminal block on the left at the bottom of the modem or at the
RJ-12 connector.
If the telecontrol connection is made at the terminal block, then a
bridging plug must be inserted into the RJ-12 connection socket.
The necessary connection to the terminals is only achieved with
the bridging plug inserted.
Connection via 2-wire leased line
Connect the 2-wire connection to the “TX” terminals on the lower
left side of the terminal block.
Connection via 4-wire leased line
4-wire connections are also connected to the lower left of the
terminal block. Connect the send cables to the “TX” terminals and
the receive cables to the “RX” terminals.
Connection via dial-up line
The following diagram shows the telecontrol connection via the
terminal block on the left at the bottom of the modem or at the
RJ-12 connector.
If the telecontrol connection is made at the terminal block, then a
bridging plug must be inserted into the RJ-12 connection socket.
The necessary connection to the terminals is only achieved with
the bridging plug inserted.
2-wire connections must be connected to pins 3 and 4 in the RJ-12
plug or to the “TX” terminals on the terminal block on the left at
the bottom.
Figure 5: Modem connection via 2-wire leased line
Figure 6: Modem connection via 4-wire leased line
TXD RXD
LEASED LINE POWER
NP
3
4TD32B
TXD RXD
LEASED LINE POWER
NP
3
4TD32B
TXD RXD
LEASED LINE POWER
NP
3
4
TD32B
TXD RXD
LEASED LINE POWER
NP
3
4
TD32B
Figure 7: Modem connection via 2-wire leased line
aTelephone exchange
b2-wire dial-up line
1) 1)
a a
b
TXD RXD
LEASED LINE POWER
NP
3
4TD32B
TXD RXD
LEASED LINE POWER
NP
3
4TD32B
1) RJ-12 connection
alternative:
2) Connection via screw terminals
2
2

XC100/X200 – PC Connection 07/04 AWB2724-1490GB
10
Modem settings
The modem settings for leased line or dial-up line connections are
made using the DIP switches.
The DIP switches can be found under the cover at the top of the
modem. The default switch setting is “OFF”.
Please follow the instructions in the modem manufacturer's
operator manual.
Dial-up line
Table 1: DIP switch SW 1: Settings for dial-up line
Table 2: DIP switch SW 2: Settings for dial-up line
hNote!
Switch Off the power supply before adjusting the DIP
switches and make sure that you adhere to the protective
measures against electrostatic charging!
DIP switch SW 1 Modem settings
PC end
Description Modem settings
XC100/200 end
PC end
XC100/XC200 end
12345678 12345678
0 0 xx––––Standard dial-up line 0 0 xx––––
0I xx– – – – Leased lines, answer function 0 I xx––––
IIxx– – – – Leased lines, dial function I I xx––––
xxIx––––Negotiation of the connection is not interrupted by
incoming signals
xxIx––––
xxxI ––––Escape sequence disabled
(commands are ignored during a connection
xxxI ––––
0 0 I 0 – – – – Current settings
0 = OFF ; I = ON ; x= not used
0 0 0 I – – – –
DIP switch SW 2 Modem settings
PC end
Description Modem settings
XC100/200 end
12345678 12345678
0xxxxxxxSwitches SW2-2 to SW2-8 are not used 0 x x x x x x x
IxxxxxxxSwitches SW2-2 to SW2-8 are used I xxxxxxx
I00xxxxxAsynchronous connection I 0 0 xxxxx
II0xxxxxSynchronous, external timing via pin 24 of the SUB-D I I 0 xxxxx
I0IxxxxxSynchronous, internal timing; the modem generates
the clocking signal
I0Ixxxxx
IIIxxxxxSynchronous slave; timing from line I I I xxxxx
IxxIxxxxDTR/DSR disabled I xxIxxxx
00000000Current settings
0 = OFF ; I = ON ; x= not used
0 0 0 0 0 0 0 0
OFF
ON
2341
OFF
ON
2341
OFF
ON
23416785

07/04 AWB2724-1490GB Modem settings
11
Table 3: DIP switch SW 3: Settings for dial-up line
Table 4: DIP switch SW 4: Settings for dial-up line
DIP switch SW 3 Modem settings
PC end
Description Modem settings
XC100/200 end
12345678 12345678
0xxxxxxx4-wire connection 0 xxxxxxx
Ixxxxxxx2-wire connection Ixxxxxxx
xIxxxxxxHandshake OFF xIxxxxxx
xxIxxxxxREL mode disabled xxIxxxxx
xxxIxxxxLoudspeaker always OFF xxxIxxxx
xxxxxIxxPLC settings xxxxxIxx
xxxxxxIxDCD follows the carrier on the line xxxxxxIx
xxxxxxxILine monitoring and reset OFF xxxxxxxI
I I 0 0 0 I I I Current settings
0 = OFF ; I = ON ; x= not used
I I 0 0 0 I I I
DIP switch SW 4 Modem settings
PC end
Description Modem settings
XC100/200 end
12345678 12345678
0000xxxxAutomatic speed and format setting 0 0 0 0 xxxx
I 000xxxx300 Bit/s I 0 0 0 xxxx
0I 00xxxx600 Bit/s 0 I 0 0 xxxx
II00xxxx1 200 Bit/s I I 0 0 xxxx
00I 0xxxx2 400 Bit/s 0 0 I 0 xxxx
I0I0xxxx4 800 Bit/s I 0 I 0 xxxx
0II0xxxx9 600 Bit/s 0 I I 0 xxxx
III0xxxx19 200 Bit/s I I I 0 xxxx
0 0 0 I xxxx38 400 Bit/s 0 0 0 I xxxx
I 00I xxxx56 600 Bit/s I 0 0 I xxxx
xxxx000x7 Bits no Parity [7N] xxxx000x
xxxxI00x7 Bits even Parity [7E] xxxxI00x
xxxx0I 0x7 Bits odd Parity [7O] xxxx0I 0x
xxxxII0x8 Bits no Parity [8N] xxxxI I 0 x
xxxx00I x8 Bits even Parity [8E] xxxx00I x
xxxxI0Ix8 Bits odd Parity [8O] xxxxI0Ix
xxxx0I I xDirect mode; [8E] or [8O] [8O] in command mode xxxx0I I x
xxxxIIIxDirect mode; [7E] or [7O] [8O] in command mode xxxxIIIx
xxxxxxxI 2 stop Bits xxxxxxxI
0 0 0 I I I 0 0 Current settings
0 = OFF ; I = ON ; x= not used
0 0 0 I I I 0 0
OFF
ON
23416785
OFF
ON
23416785

XC100/X200 – PC Connection 07/04 AWB2724-1490GB
12
Table 5: DIP switch SW 5: Settings for dial-up line
Leased line
Table 6: DIP switch SW 1: Settings for dial-up line
DIP switch SW 5 Modem settings
PC end
Description Modem settings
XC100/200 end
12345678 12345678
0000xxxxUse saved parameters 0 0 0 0 xxxx
I000xxxxV.21, 300 Bit/s I 0 0 0 xxxx
00I 0xxxxV.22, 1 200 Bit/s 0 0 I 0 xxxx
I0I0xxxxV.22, up to 2 400 Bit/s I 0 I 0 xxxx
0I I 0xxxxV.32, up to 4 800 Bit/s 0 I I 0 xxxx
III0xxxxV.32, up to 7 200 Bit/s I I I 0 xxxx
000I xxxxV.32, up to 9 600 Bit/s 0 0 0 I xxxx
I00IxxxxV.32, up to 12 000 Bit/s I 0 0 I xxxx
0I 0I xxxxV.32, up to 14 400 Bit/s 0 I 0 I xxxx
IIIIx x x x Auto detect mode I I I I x x x x
I I I I 0 0 0 0 Current settings
0 = OFF ; I = ON ; x= not used
I I I I 0 0 0 0
OFF
ON
23416785
Modem settings
PC end
Description Modem settings
XC100/200 end
PC end
XC100/XC200 end
12345678 12345678
00xx– – – – Standard dial-up line 0 0 xx––––
0I xx––––Leased lines, answer function 0 I xx––––
I I xx––––Leased lines, dial function I I xx––––
xxIx––––Negotiation of the connection is not interrupted
by incoming signals
xxIx––––
xxxI ––––Escape sequence disabled
(commands are ignored during a connection
xxxI ––––
I I I I – – – – Current settings
0 = OFF ; I = ON ; x= not used
0 I I I – – – –
OFF
ON
2341
OFF
ON
2341

07/04 AWB2724-1490GB LED status indication
13
LED status indication
PWR Full intensity The modem is in normal
operation
Half intensity The modem is in test mode
Flashing, with click in
the loudspeaker
Voltage supply problems
Flashing with 1 : 6
(ON : OFF)
RAM defective
ON/OFF, with click in
the loudspeaker
Modem unable to start
LINE LED is On when the modem has a line
ANS LED flashes when an incoming call is recognised.
ANS is On continuously while an incoming call is being
answered and subsequently dims once the call has been
answered.
REL The LED flashes when the modem is in fault correction
mode or in compressed mode. It is On continuously
when the modem is only in the fault correction mode.
During direct or normal operation, the LED is Off.
TD Transmitted data. Indicates that data are being received
at the local RS-232 port.
RD Received data. Indicates that data are being sent from
the local RS-232 port.
RTS Request To Send from the DTE
DCD Data Carrier Detect modem signal
DSR Data Set Ready modem signal

07/04 AWB2724-1490GB
14

07/04 AWB2724-1490GB
15
3Programming
A simple user program (counter function with LED display) serves
as an example.
Modem connection via leased and dial-up lines
The communication connection between the two modems is
established via a leased or dial-up line. The following illustration
takes consideration of both of these connection types.
Perform the following steps for this purpose:
XOpen a new project in XSoft with the fundamental, user
relevant project parameters.
XCreate the user program.
XDefine the communication parameters.
Communication parameters
XAccess the menu with ‹Online lCommunication parameters l
New›.
After you have defined the communication connection type and
name, confirm with OK.
A new window opens after confirmation. Enter the communication
specific connection parameters. Complete the default parameters
as described in Table 7.
Table 7: Default parameter expansion and their meaning
Figure 8: Communication connection via dial-up line
Figure 9: Communication connection via leased line
Figure 10: Communication parameters with dial-up line
Figure 11: Communication parameters with leased line
Name Default
value
Default value
with
amendment
Note
Init AT&F0 AT&F0X3 If you add “X3” (without
space and/or special
characters), this
deactivates the
monitoring for engaged
tone during a dialling
attempt
Dial ATDT ATDT1875 Add the target telephone
number (without space
and/or special
characters)

Programming 07/04 AWB2724-1490GB
16
Connection between PC and control
Once the compiled program is present and the communication
parameters are set, establish the connection between the
programming PC and the PLC via ‹Online – Log-in›.
XLoad the user program into the PLC with the “Log-in”
command.
XStart the PLC with the “START” command.
The status display is activated.
ONLINE modification
For a connection via a leased line and dial-up line, you can use the
ONLINE modification function as described in the ONLINE
documentation of XSoft.
Figure 12: Status display via modem connection with a leased line or dial-up connection