Mold-Masters Tempmaster M1 User manual

© 2021 Mold-Masters (2007) Limited. All Rights Reserved.
Quick Guide for Tempmaster™ M1
Plus Controller
Refer to the M1P Controller User Manual for full instructions and safety information.
Create a New Tool
1. Choose [Menu] to open the ToolStore page.
2. Choose a blank tool slot then choose [Detect].
3. Enter system password.
4. Type in a new name for the tool.
5. Choose [Enter].
Congure Control Cards
1. Choose the rst zone to be congured.
2. Choose the last zone to be congured.
3. Choose [Range] to include all zones in between.
4. Choose [Set] to see the Congure Card Slot menu.
5. Choose zone type: manifold, spear, monitor, special or not used.
6. Choose header color.
7. Choose [OK].
8. Repeat steps 1 through 4 until all zones are congured.
Note: zones populate with default values which can be accepted or
changed.
Congure Tool Parameters
1. Choose zones of the same type.
2. Choose parameter.
3. Choose [Set].
4. Set value.
5. Choose [Enter].
Note: see User Manual for full listing and description of tool
parameters.
Congure Controller Parameters
1. Choose [Cong] to view the global parameters.
2. To view the global parameters and their current settings, choose
[List].
3. Choose setting and required option / function.
4. Choose [OK] to keep the changes or choose [Cancel] to leave
without making changes.
Note: see User Manual for full listing and description of global
parameters.
Congure the ControllerMain Screens and Menus
Main Screens and Menus
Congure the Controller
Create a New Tool
Congure Control Cards
Congure Tool Parameters
Congure Controller Parameters
Congure Zone Settings
Set Probe and Manifold Temperatures
Save to the Toolbank
Operate the Controller
Startup Procedure
Change Or Set Zone Temperatures
Change Modes - Individual Zones
Change Modes - Multiple Zones
Check Zone Performance
Shutdown Procedure
Global Support
Main Page Functions:
• Monitor - observe zone
condition
• Control - choose mode
• Navigation - [Menu]
button opens the
Navigation screen
ToolStore Page Description:
List of tools with names and
saved settings
Utilities Page Gives access to:
• Exit
• Cong
• Export
• Quad IO
Setup Page Description:
User can congure and
alter global and specic tool
parameters.
Graph Page Description:
Displays historical record
of the last 30 minutes of
operation

M1P--QG--EN--00--09-1
Global Support
Global Headquarters
CANADA
Mold-Masters (2007) Limited
tel: [phone]
[email protected]
European Headquarters
GERMANY
Mold-Masters Europa GmbH
tel: [phone]
[email protected]
Asian Headquarters
CHINA
Mold-Masters (KunShan) Co, Ltd
tel: [phone]
[email protected]
South American Headquarters
BRAZIL
Mold-Masters do Brasil Ltda.
tel: [phone]
[email protected]
India
Mold-Masters Technologies
Private Limited
tel: [phone]
[email protected]
Japan
Mold-Masters K.K.
tel: [phone]
[email protected]
United Kingdom
Mold-Masters (UK) Ltd
tel: [phone]
[email protected]
U.S.A.
Mold-Masters Injectioneering LLC
tel: [phone] (USA only)
tel: [phone]
[email protected]
Original Instructions
Congure Zone Settings
1. Choose the rst zone to be congured.
2. Choose the last zone to be congured.
3. Choose [Range] to include all zones in between.
4. Choose [Set].
5. Set the required value.
6. Choose [Enter] to keep the new setting or [Esc] to exit the
screen without saving.
Set Probe and Manifold Temperatures
1. Choose [Set] and enter password if prompted.
2. Choose [Auto] and use the keypad to set a new temperature.
3. Choose [Enter] to keep the new temperature or [Esc] to exit the
screen without saving.
Save to the Toolbank
1. Choose the ToolStore page.
2. Choose the required tool.
3. Choose [Save].
Operate the Controller
Startup Procedure
1. Use the main switch to energize the cabinet.
2. After the cabinet is switched on, press the console switch until
the display lights up.
Once the display screen is on, the console has two options:
• If console startup is set to Stop, then the tool remains at
zero power, and it does not heat up.
• If the console startup is set to Startup, Standby or Run,
the controller applies power to the zones so that they heat
up.
Change Or Set Zone Temperatures
1. Choose one zone.
2. Choose another zone.
3. Choose [Range].
4. Choose [Set].
If prompted, enter the System password.
5. Choose one of the options:
• [Set] - set a new temperature
• [Add] - raise the overall temperature
• [Sub] - lower the overall temperature
6. Enter the required value.
The new temperature is shown on the Main page.
Change Modes - Individual Zones
1. Choose one or more zones.
2. Choose [Set] and enter password if prompted
3. Choose one of the following options:
• [Set] - set a new temperature
• [Plus] - raise the overall temperature
• [Minus] - lower the overall temperature
4. Enter the required value.
The new temperature is shown on the Main page.
5. Choose [Enter] to keep the new temperature or [Esc] to exit the
screen without saving.
Change Modes - Multiple Zones
1. From the Main page, choose [Button One] or [Mode], then choose
the required Mode button.
2. Choose [OK] to conrm or choose [Cancel] to leave without
changing settings.
Mode Options
[Run] Switches all zones on
[Stop] Switches all zones o󰀨
[Standby] Reduces temperature in all zones with Standby
temperatures congured
[Startup] Begins startup sequence congured on the Setup page
[Shutdown] Begins switch o󰀨 sequence determined by Startup
mode
[Boost] Temporarily increases temperatures in zone with Boost
temperatures congured
[Purge] Guides user through color change routine
Check Zone Performance
The controller records temperature history and displays a graph of
temperature for the last 30 minute time period.
1. Choose up to six zones.
2. Choose [Graph].
3. Choose [Key] to expand graph size.
4. Choose any of the top four [Zoom] buttons to expand the time of
the temperature scale.
5. Drag either scale to shift the display.
Note: once the Zoom button is used then the graph locks at that moment
in time and does not update.
Shutdown Procedure
1. On the Main page, choose [Stop] mode to reduce the heating to
zero.
2. On the Utils page, choose [Exit] to shut down the console
computer.
3. Use the main power switch to isolate all power to the whole system.