Mold-Masters TempMaster M2 Plus Series User manual

© 2021 Mold-Masters. All Rights Reserved.
M2P Quick Guide
GLOBAL SUPPORT
GLOBAL HEADQUARTERS
CANADA
Mold-Masters (2007) Limited
tel: [phone]
[email protected]
EUROPEAN HEADQUARTERS
GERMANY
Mold-Masters Europa GmbH
tel: [phone]
[email protected]
ASIAN HEADQUARTERS
CHINA
Mold-Masters (KunShan) Co, Ltd
tel: [phone]
[email protected]
SOUTH AMERICAN HEADQUARTERS
BRAZIL
Mold-Masters do Brasil Ltda.
tel: [phone]
[email protected]
INDIA
Mold-Masters Technologies
Private Limited
tel: [phone]
[email protected]
JAPAN
Mold-Masters K.K.
tel: [phone]
[email protected]
UNITED KINGDOM
Mold-Masters (UK) Ltd
tel: [phone]
[email protected]
U.S.A.
Mold-Masters Injectioneering LLC
tel: [phone] (USA only)
tel: [phone]
[email protected]
Original Instructions
SAVE A TOOL / SETTINGS TO THE TOOLSTORE
1. Choose the ToolStore page.
2. Choose the required tool.
3. Choose [Save].
SET ZONE TEMPERATURE
1. Choose the required zone or zones.
2. Choose [Set].
3. Choose one of the options:
• Enter a new value for the temperature
• Choose [Add] - raise the overall temperature
• Choose [Subtract] - lower the overall temperature
4. Choose [Enter] to set required temperature or choose [Esc] to
leave without making changes.
SETUP THE EASYVIEW SCREEN
STEP ONE: IMPORT A PICTURE
1. Save one or more pictures onto the USB memory stick.
2. Insert the USB memory stick into the console and wait 10
seconds.
3. Choose [Pictures].
4. Choose [Import] and enter password if required.
5. Choose the required picture or choose [Cancel] to exit without
importing.
STEP TWO: LINK A PICTURE
1. Choose the required picture.
2. Choose [Link] and enter password if required.
3. Choose an empty slot and press [OK] to make the link or
[Cancel] to return to the Easyview screen.
STEP THREE: ADD MINI PANEL TO TOOL PICTURE
1. Choose the required picture.
2. Choose [Show] and enter password if required.
3. Choose [Place] to open the zone selection box.
4. Choose [Auto] or [Alias Name].
• [Auto]: the zones will be placed sequentially where the
user touches the screen. There is no need for the user to
press [Place] before every zone.
• [Zone number or alias]: the user chooses a specic zone
to place and must press the [Place] button each time a
new zone is to be located.
5. Choose [Cancel] to return to the Easyview screen without
adding a mini panel.
OPERATE THE CONTROLLER
STARTUP PROCEDURE
1. Use the main switch to energize the cabinet.
2. After the cabinet is switched on, press the console switch until
the display lights up.
Once the display screen is on, the console has two options:
• If console startup is set to Stop, then the tool remains at
zero power, and it does not heat up.
• If the console startup is set to Startup, Standby or Run,
the controller applies power to the zones so that they heat
up.
LOAD TOOL SETTINGS
1. Choose the required tool and choose [Load].
2. Choose [OK] or choose [Cancel] to exit.
NOTE: if the controller is in Run mode and a tool with a di󰀨erent
temperature setting is loaded, then the tool will immediately change
to run at the new incoming temperature setting.
CHANGE MODES - INDIVIDUAL ZONES
1. Choose the required zone.
2. Choose [Set] and enter password if required.
3. Then choose one of the two following options:
• [Boost]: to raise the temperature of that zone until Boost time
expires.
• [OFF]: to switch o󰀨 the zone.
CHANGE MODES - MULTIPLE ZONES
1. Choose the required zones.
2. Choose [Set] to display the keyboard.
3. Choose one of the following options:
• To change to Manual mode: choose [Manual] and set
percentage power.
• To Slave a zone: choose [Slave] and choose a similar Master
zone from the zone list.
• To return to Auto mode: choose [Auto] and enter the required
zone temperature.
CHECK ZONE PERFORMANCE
The Graph screen showns graphs of temperature versus time or power
versus time for up to 20 zones.
1. Choose [Graph] to open the Graph screen.
2. Choose [Timeline] to show history of operation for the tool.
3. Choose [Power] to show power on the bottom axis of the graph.
4. Choose [Temp] to show temperature on the bottom axis of the
graph.
5. Choose [Scale] to choose the required time interval. Options
include: 5 minutes, 30 minutes or 24 hours.
6. Choose [] or [] to move up or down through the zones.
SHUTDOWN PROCEDURE
1. Choose [Mode] from the Display screen and enter password if
required.
2. Choose [Stop] to reduce the heating load to zero.
3. Choose [Shutdown] from either the Mode box or from the upper
menu buttons and then accept the conrmation on the screen.
4. Choose [ ].
5. From the Information screen choose [Exit].
6. Choose [OK] to turn the console o󰀨 or choose [Cancel] to return to
the Information screen.

2021 Mold-Masters. All Rights Reserved.
M2P--QG--EN--00--03-1
QUICK GUIDE FOR TEMPMASTER™
M2 PLUS CONTROLLER
Refer to the M2P Controller User Manual for full instructions and safety information.
CREATE A NEW TOOL
1. Choose [ToolStore].
2. Choose an empty tool slot then choose [Detect].
3. Enter password if required.
4. Enter tool name.
CONFIGURE CONTROL CARDS
1. Choose [Settings].
2. Choose a zone from the Type column.
3. Choose [Set].
4. Choose zone type.
5. Change header color if required.
6. Choose [OK] to accept the changes or [Cancel] to return to the
Settings screen without saving any changes.
NOTE: all temperature control cards initally default to probe zones and
use probe default values.
CONFIGURE TOOL PARAMETERS ZONE BY ZONE
1. Choose [Settings].
2. Choose the zone or zones to be congured and choose the
column of the required parameter.
3. Choose [Set] and enter password if required.
4. Set the required value.
5. Repeat steps 2 through 5 for each parameter that requires
adjustment.
NOTE: see user manual for a list and descriptions of tool parameters.
CONFIGURE TOOL / SYSTEM SETTINGS
1. Choose [Settings] and then choose [Cong].
2. Enter password if required.
3. Choose [Tool Cong] from Tool Settings or [System Cong] from
System Settings.
4. Choose the required setting and enter the required value or
option.
5. Choose [OK] to accept the value or choose [Back] to return to the
Tool or System Cong screen without saving.
IMPORTANT: to save any setting change permanently, the user must
save it to the ToolStore.
CONFIGURE THE CONTROLLERMAIN SCREENS AND MENUS
MAIN SCREENS AND MENUS
CONFIGURE THE CONTROLLER
CREATE A NEW TOOL
CONFIGURE CONTROL CARDS
CONFIGURE TOOL PARAMETERS ZONE BY ZONE
CONFIGURE TOOL AND SYSTEM SETTINGS
SAVE A TOOL / SETTINGS TO THE TOOLSTORE
SET ZONE TEMPERATURE
SETUP EASYVIEW SCREEN
OPERATE THE CONTROLLER
STARTUP PROCEDURE
LOAD TOOL SETTINGS
CHANGE MODES - INDIVIDUAL ZONES
CHANGE MODES - MULTIPLE ZONES
CHECK ZONE PERFORMANCE
SHUTDOWN PROCEDURE
GLOBAL SUPPORT
Display Screen Functions:
Monitor and Information:
observe zone condition
Control: side command buttons
change from page to page
Navigation: tabs allow the user to
switch between the di󰀨erent pages
ToolStore Screen Description:
List of tools with names and saved
settings.
Apps Screen Gives access to other pages:
• Testing
• Export
• Pictures
• Actions
• Alarms
• Remote
• Energy
• Purge Wizard
• Smart Mold
Settings Screen Description:
Gives access to tool and system
settings.
Graph Screen Description:
Displays graphs of temperature
or power versus time for up to 20
zones.