Monte Carlo Fan Company 5DI52XXD-L Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
5DI52XXD/5DI52XXD-L Series Fan
Total an weight with light
UL Model No. : 5DI52
8.5 kgs
18.7 lbs

© 2013 Monte Carlo Fan Company 8/13/2013
2
WARNING: T REDUCE THE RISK F FIRE, ELECTRIC SH CK, R INJURY T PERS NS, BSERVE THE F LL WING: READ
AND SAVE THESE INSTRUCTI NS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including
fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the
outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up
into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the
trailing edge of the blade.
WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The utlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-
move Knockouts In The utlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign
object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-
turer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigera-
tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2013 Monte Carlo Fan Company 8/13/2013
3
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley
fastened by at least two points to a structural
ceiling member ( a loose box will cause the fan
to wabble). Use only the screws provided
with the outlet ox.
3
21
Loosen the 2 set screws till you can not
feel them on inside of yoke.
Note: If install fan on vaulted ceiling,
make sure open end of mounting
bracket is installed facing the higher
point of the ceiling and make sure the
ceiling angle is not steeper
than 30º.
4
yoke
Place downrod into fan yoke.
7
Install the keeper to pin.
9
Align the hole in the Downrod with the hole in
the Yoke. Insert the Pin through the Yoke and
Downrod until the point appears on the other
side.
8
Downrod mount installation
Remove Keeper pin and cross pin
from downrod. Place canopy and
caonpy disk cover over downrod.
Canopy
Tread leadwires and safety
cable through downrod.
Downrod
6
5
Canopy
disk
Cross
pin
Keeper
pin
Downrod

© 2013 Monte Carlo Fan Company 8/13/2013
4
Hang assembled fan from the mounting bracket in-
stalled to ceiling in previous step. Make sure the fan
is hanging straight. Rotate fan until the tab on the
Mounting bracket engages the slot on the Downrod
Ball. This must be done to prevent the fan body from
rotating when the blades are in motion.
11
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
15
Make sure the studs protruding from the
bottom of the Mounting bracket are in-
stalled with threads all the way through
the bracket.
13
Tighten the 2 set screws on the yoke
once the downrod is in place.
10
Make wiring connections as indicated
above. Connect black and blue wire from
fan to Black or (Hot) wire from house.
Connect White wire from Fan to White
( eutral) wire from house. Connect
Ground leads from mounting bracket and
downrod to Ground lead from house.
Refer to Safety Tips section of manual.
14
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do ot Remove Knockouts In
The Outlet Box.
12 Safety cable installation
Safety Ca le
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer
Remove every other screw as circled
and save for later use.
Note: Flushmount is not available
with vaulted ceiling.
17
Go to step 26
Flush mount installation
16
Cover
Ring
Lift Conopy allowing the 2 studs to
protrude through the canopy.
ext lift the cover ring and install knurled
nuts as shown. Tighten the knurled nuts
securely. The canopy should adjust for
any irregularity in the ceiling or Outlet
box.

© 2013 Monte Carlo Fan Company 8/13/2013
5
Check the motor for shipping stabiliz-
ers and remove if present. Attach
blades using screws and washers in
hardware pak. Tighten screws se-
curely.
26
Remove side covers from canopy exposing
4 holes. 2 closed holes and 2 open “L”
shape holes and then Pass leadwires and
safety cable through the canopy.
19
“L” shape
slots
Install rubber pad between fan
body and canopy.
18
Remove the all thread studs from the
lower part of the mounting bracket. Hang
fan from mounting bracket by the
hands free hook into a closed hole on
the edge of the Canopy. Note: For
Canadian mounting refer to Step #12.
21
Hands free hook
Place canopy over fan body align-
ing holes.
Replace the 3 screws removed and
tighten securely. Check motor for
shipping stabilizers and remove if
present.
20
Take 4 screws from hardware pack
and install one on each side of
bracket to match the L slot screw
holes in canopy. Keep 2 screws for
later use.
22
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
24
Lift fan to mounting bracket, aligning the “L”
shape holes with the screws on the mounting
bracket. Turn the fan clockwise to lock in
position. Install the other 2 screws included
in hardware bag and tighten all 4 securely.
25
Make wiring connections as indicated
above. Connect black and blue wire from
fan to Black or (Hot) wire from house.
Connect White wire from Fan to White
( eutral) wire from house. Connect
Ground leads from mounting bracket and
downrod to Ground lead from house.
Refer to Safety Tips section of manual.
23

© 2013 Monte Carlo Fan Company 8/13/2013
6
Install 3 screws to install light pan.
32
Connect plug from fan to switch
house plug. Be sure plugs connection
snap together completely.
29
Install by twisting clockwise, add 1
screw removed step 27 to switch
housing plate. Tighten the 3 screws
securely.
28
Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture.
31
Loosen the pre installed screws of
switch housing plate. Save removed
screw for use later.
Install a JD 75 watt halogen bulb, bulb in-
cluded.
Caution: Do not replace bulb until it cools
down.
WARNING: Over lamping the fan will re-
sult in the fan lights shutting down until
the proper wattage of bulbs are installed.
Reset the lights by turning off the wall
switch, breaker,or by remote. Replace bulbs
with the correct wattage bulbs, turn the
power on.
33
30
Attach glass by locating dimples in
light fixture with the groves in glass
and twisting clockwise till tight.
34
Setting the reverse switch in the left hand
side will result in downward airflow and set-
ting the switch in the right hand side will re-
sult in upward airflow.
Note: Reverse switch must be set either
completely LEFT or completely Right for fan
to function. If the reverse switch is set in the
middle position, fan will not operate.
35
Reverse switch
Left hand side
(Forward)
Right hand side
(Reverse)
Loosen 2 screws and remove 1 screw
from motor plate. Save removed
screw for use later.
27

© 2013 Monte Carlo Fan Company 8/13/2013
7
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate
when switch is in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off efore entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-
ware are finger tight. Check to be sure light bulb is tight in socket and not touching glass
shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band
on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT
USE a Solid State varia le speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the
notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-
tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can ad-
just blade levels by the following procedure. To adjust a blade tip down, insert a washer (not
supplied) between the blade and blade holder at the screw closest to the motor. To adjust a
blade tip up, insert washer (not supplied) between the blade and blade holder at the two
screws farthest from the motor. Reverse the position of the washer if blades mount from top
of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can re-
distribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WARNING: Over lamping the fan will result in the fan lights shutting down
until the proper wattage of ul s are installed.
Reset the lights y turning off the wall switch, reaker,or y remote. Replace ul s
with the correct wattage ul s, turn the power on.
CAUTION: Make sure main power is turned off efore entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTI G
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-
tion, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service discon-
necting means to prevent power from eing switched on accidentally. When the service disconnecting
means cannot e locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Trou le Suggested Remedy

Apr.2013
May.2013 CUL requirement
Aug.2013 dual mount