morse 15 User manual

IMPORTANT:
1. Review the Material Safety Data Sheet(s) for the material(s) in the
can(s) and take all necessary precautions. Safety shoes, work
gloves, hard hat and other personal protective devices are recom-
mended.
2. Please read all instructions thoroughly before attempting to operate
your new MORSE Can Tipper.
3. The model 15 is designed to pour a 5-gallon can weighing up to 75
Lb. DO NOT exceed these ratings. Exceeding these ratings or
handling cans other than those mentioned above is unsafe and
could result in equipment damage or excessive wear.
4. When loading, unloading, operating, or maintaining your MORSE
Can Tipper, always use care and good judgment. Maintain secure
footing and a firm hold. Keep hands and loose clothing away from all
moving parts. Read operating instructions and review the pictures in
the sales brochure before operation.
Receiving Procedures
Every Morse product is inspected prior to shipping. However, damage
may be incurred during transit.
• Check for visible damage. If you choose to accept damaged freight,
always sign noting the damage on the BILL OF LADING.
• Document the damage and have the truck driver sign. We recommend
keeping a digital camera at your receiving dock for this purpose.
• Open packages expeditiously to check the condition of the goods. There
is only a 24 hour window to notify the carrier of any concealed damage.
• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING
COMPANY! Then you may contact Morse for assistance with your
freight claim.
• Morse Manufacturing will not be held responsible for any damaged
freight that is not signed for as damaged.
Delivery to non-business addresses without a loading dock result in
additional freight charges. Residential delivery fees, inside delivery fees,
re-delivery charges, and lift gate services will be added by the truck line,
and are non-negotiable.
Limited 2 Year Warranty
Morse drum handling equipment is guaranteed against defects in
workmanship or materials for TWO YEARS when used properly within
its rated capacity. Warranty does not cover wear from normal use or
damage from accident or abuse. Motors and other purchased parts carry
the warranties of their manufacturers.
MORSE MFG. CO., INC. • 727 West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518
Phone: [phone] • Fax: [phone] • Email: [email protected] • Website: www.MORSEmfgco.com
COPYRIGHT 2006 MORSE MFG. CO., INC. Form PL 15 (0506) (Updated 10/2006) Page 1
MODEL 15
CAN TIPPER
The Specialist In Drum Handling Equipment
Contents
Page
Receiving Procedures. . . . . . . . . . . . . . . . . 1
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2
Parts Lists and Diagrams. . . . . . . . . . . . . . . . . 3
Operator’s Manual
for Morse Can Tipper Model 15
Manufactured 05/2006 to _______
For warranty claims, contact your Morse Dealer to obtain a
return authorization number, and for return freight advice. Return freight
must be prepaid.
In all instances, liability is limited to the purchase price paid or to repairing
or replacing the product. Customer assumes liability for any
modifications, unauthorized repairs or parts substitution.
Safety Information
While Morse Manufacturing Co. equipment is engineered for safety and
efficiency, a high degree of responsibility must be placed upon the machine
operator to follow safe practices, based primarily on common sense,
upon which true safety depends.
Failure to follow the safety precautions in this manual can result in
personal injury or property damage. Observe the same precautions as
with similar machinery where carelessness in operating or maintenance
is hazardous to personnel. Carefully read the safety precautions below
and throughout this manual.

MODEL 15
CAN TIPPER
The Specialist In Drum Handling Equipment
Website: www.MORSEmfgco.com
COPYRIGHT 2006 MORSE MFG. CO., INC. Form PL 15 (0506) (Updated 10/2006) Page 2
ASSEMBLYINSTRUCTIONS:
1. Please unpack and identify the following parts:
1 - Can Holder with Catch
1 - Base Assembly
1 - Center Brace
6 - 1/4-20 x 5/8 Panhead Screws
6 - 1/4-20 Two Way Lock Nuts
2. Spread the base assembly open, hinging at the base riveted
joints (see curved arrow A in parts diagram).
3. Fasten the center brace in place using four screws and nuts
as shown. Tighten securely.
4. Rotate the can holder ring to horizontal position, hinging at the
holder riveted joint, with the catch upright as shown (see
curved arrow B in parts diagram).
5. Place the can holder between the uprights of the base as
shown. Insert screws (from inside of ring) through holes in the
can holder ring and through the base uprights. Thread the
nuts onto the bolts but do not tighten completely. The nuts
should be just loose enough to allow the can holder to pivot
freely.
6. Place a few drops of oil on the pivot bolts before using and
reapply oil periodically to minimize wear.
MAINTENANCE:
1. Periodically inspect all moving parts, framework, and contact
areas for signs of wear, fatigue, or loosening.
for Morse Can Tipper Model 15
Manufactured 05/2006 to _______
Safety Information (continued)
WARNING - Indicates a situation which, if not avoided, could result in serious injury or death.
CAUTION - Indicates a situation which, if not avoided, can result in damage to the machine.
CAUTION - Do Not Modify the Unit - Under no circumstances should any modifications be made to the Morse
machinery without factory authorization. Any modifications may void the warranty. This machine was designed to
perform a specific job and alterations may result in injury to operator or damge to the machine.
WARNING - No Loose Fitting Clothing - Wear close-fitting clothing and safety equipment appropriate to the job.
Loose fitting clothing may become caught on the machinery and cause severe personal injury.
WARNING - Wear Safety Shoes -
Wear safety shoes with non-slip
soles and hard toe protection.
CAUTION: DO NOT exceed
weight capacity of 75 Lb.

Parts List and Diagram
for Morse Can Tipper Model 15
Manufactured 05/2006 to _______
MODEL 15
CAN TIPPER
The Specialist In Drum Handling Equipment
Website: www.MORSEmfgco.com
COPYRIGHT 2006 MORSE MFG. CO., INC. Form PL 15 (0506) (Updated 10/2006) Page 3
ITEM QTY PART # DESCRIPTION
1 1 1687-P CAN HOLDER ASM, 15
2 1 4283-P CATCH ASM, 15 W/ SCREW
3 2 4234-P CAP, PLASTIC, HANDLE, CATCH 15
4 1 1686-P SCREW, THUMB, 5/16-18 X 3/4
5 6 1518-P NUT, LOCK, 1/4-20 NYLON
6 6 1517-P SCREW, PANHEAD, 1/4-20 X 5/8
7 1 4277-P BASE ASM, 15 SERIES
8 1 4281-P CENTER BRACE, 15