The Specialist In Drum Handling Equipment
Model 185i/E
Kontrol-Karrier with Fiber Drum Strap,
Accepts Diameter Adaptors
Operator’s Manual for Morse Model 185i/E Kontrol-Karrier with Fiber Drum Strap, Accepts Diameter Adaptors
Serial number 0403 to 0309 (MMYY)
www.MORSEmfgco.com
Copyright 2009 - Morse Mfg. Co., Inc. Form PL185iE (0403-0309) (Updated March 16, 2018 9:47 AM) 3
Machine Description
Model 185i/E Kontrol-Karrier is designed to lift, transport and dispense a standard
55-gallon steel drum 22.5” in diameter. The maximum capacity is 800 Lb.
Options
A smallerdiameterdrum canbehandled withthecorrectsize55/30SeriesDiameter
Adaptorinstalled(seeDiameterAdaptorliterature).
Important
Review the Material Safety Data Sheet(s) for the material(s) in the drum(s) and take all necessary precautions. Safety shoes, work1.
gloves, hard hat and other personal protective devices are recommended.
Please read all instructions thoroughly before attempting to operate your new Morse drum handler.2.
The185SeriesKontrol-Karriershaveamaximumcapacityratingof800Lb.foraFULLdrumand500Lb.foraHALF-FULLdrum,and3.
are designed to lift and move a drum of the size and type noted above. DO NOT exceed this rating. Exceeding this rating or handling
drums other than those mentioned above is unsafe and could result in equipment damage, excessive wear, awkward or dangerous
handling.
When loading, unloading, operating, or maintaining your MORSE drum handler, always use care and good judgment. Maintain secure4.
footingandarmhold.Keephandsandlooseclothingawayfromallmovingparts.Neverallowanyonetobebelowanypartofaraised
drum handler or drum. Read operating instructions and review the pictures in the sales brochure before operation.
The185Seriesarea“Group1structuralandmechanical”below-the-hookliftingdevicewhicharecoveredbytheAmericanNational5.
StandardASMEB30.20.Theusershouldcomplywithallaspectsofthisstandard.
Operating Instructions
StartwithKontrol-Karrierontheoor.LowerhoistandengagehoisthooktoliftKontrol-Karrier.1.
RaisehoisttoliftKontrol-Karrierclearofoorandtransportittothedrum.2.
Suspend Kontrol-Karrier at a height which aligns drum saddle with center of drum. Swing ratchet hinge plate (item 37) to open3.
position.
With binder strap (item 26) hanging freely, push Kontrol-Karrier against drum so that saddle will encircle drum.4.
Secure the drum: drape the binder strap (item 26) across the face of the drum and5.
engage a link into the slot in the ratchet (item 32). Turn the ratchet clockwise to
tighten strap. If the strap doesn’t cinch tightly on the drum, lift the pawl (item 30) to
loosen and release the strap and try again with a different link in the notch. Firm
hand pressure on the ratchet handle should tighten the strap sufciently to hold
the drum. DO NOT use mechanical aids such as a pipe to extend handle for extra
leverage.
Raise hoist and position drum at pouring station.6.
Pour the drum by pulling on the pull chain (item 3) and rotating the drum to a7.
suitable pouring angle. For best control of drum pouring angle, pay out one side of
the chain loop while pulling in the other side, thus being able to hold back the drum
rotation. The chain lock on the bottom of the power arm can be used to prevent drum
rotation. To do so, criss cross the chain and insert in each slot of the chain lock. If
thedrumhandlerisequippedwiththeMORStopTilt-Brake,thereisnoneedtohold
tensionon bothsidesof thechainloop. Brakingisimmediate andselfactuating,
without additional steps by the operator.To add the MORStop Tilt-Brake to your
drumhandler,orderpart#3900-Pforaeldinstallationkit.
Afterpouringiscompleted,rotatedrumbacktoverticalpositionandlowerhoisttoreturndrumtooor.8.
To remove drum: Pull ratchet handle clockwise to relieve pressure on ratchet teeth. Lift pawl handle (item 30) to release teeth9.
engagement and rotate ratchet to loosen strap and allow its removal from notch.
Maintenance
Lubricate gear teeth and roller chain.1.
Clean and oil ratchet, pawl and other moving parts periodically to maintain free action and reduce wear. Clean and lubricate more often2.
in environment where dust, dirt or other foreign particals will effect the performance of moving parts.
Periodically inspect all moving parts, framework and contact areas for signs of wear, fatigue or loosening. Tighten, adjust or replace3.
parts as necessary to prevent failure and maintain proper function.
The inner drum gripping surface of the Fiber Drum Strap (item 26) should be kept clean to maintain its ability to grip the drum.4.
