Morso 3112 B User manual

MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORSMORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS
E-Mail: [e-mail] · Website: www.morsoe.comE-Mail: [e-mail] · Website: www.morsoe.com
Installation and Operating Instructions
3112 B & 3142 B
For use in North America

2
DK ENG
1.0 Installation of your Morsø stove Page no.
1.1 Unpaking the stove 4
1.2 Checking loose parts in the stove 5
1.3 The chimney / ue system 6
1.4 Flue connection 6
1.5 Connection to the existing chimney 8
1.6 Positioning the stove 10
2.0 Operation 11
2.1 Before you start ring 11
2.2 Lighting & loading intervals 12
3.0 Maintenance 15
3.1 Exterior maintenance 15
3.2 Internal maintenance 15
3.3 Cleaning the stove & the ue 17
3.4 Leaving the stove for extended periods 18
3.5 Parts diagram 19
3.6 Parts list 20
Contents
Congratulations on the purchase of your new
Morsø stove!
Morsø, which is the largest supplier for the Dan-
ish market, has manufactured stoves of the highest
quality since1853. By following the instructions over-
leaf, we are sure that you will enjoy the use and the
benets of your stove for many years to come.
Read this entire manual before you install and use your new room heater. If this room
heater is not properly installed, a house re may result. To reduce the risk of re, follow
the installation instructions. Failure to follow instructions may result in property dam-
age, bodily injury, or even death.
Contact local building ocials about restrictions and installation inspectionrequirements
in your area.
Save these instructions

3
Optional Accessories
A wide range of accessories (such as handling gloves, reside tools, glass cleaner and heat-
proof paint) are available for use with your Morsø stove. They help with day-to-day running
and maintenance. Contact your Morsø dealer for more information.
The Morsø 3112 B & 3142 B meets the U.S. Environmental Protection Agency’s
emission limits for wood heaters sold on or after May 15, 2020.
The Morsø 3112 B & 3142 B have been certied by PFS TECO. The test standards are
UL-1482-2011 for the United States and ULC-S627-00 for Canada.
The stove is listed for burning wood only. Do not burn other fuels.
Under specic test conditions this heater has been shown to deliver heat at rates ranging
from 9,199 to 28,000 Btu´s.
This wood heater needs periodic inspection and repair for proper operation. It is
against federal regulations to operate this wood heater in a manner inconsistent with oper-
ating instructions in this manual.
Cast iron
Cast iron is a live material. There are no two ovens that are identical. This is partly due to the
tolerances of the casting process, partly because the ovens are a work of craftsmanship.
Minor unevennesses may also occur in the cast iron surface.
Portland,Oregon
USA
Certied &
Listed By
PFS TECO
Report Number: F20-580

4
DK ENG
Installation of woodburning stoves must be safe and legal.
If your Morsø stove is not installed correctly, it may cause a house re. To reduce the risk
of re, the installation instructions must be followed carefully. Contact the local building
ocials about restrictions and installation inspection in your area.
Before you start installing your stove, make sure that:
- The stove and chimney connection are placed far enough from combustible materials to
meet all clearance requirements.
- The oor protection must be adequate and must be made correctly according to the re-
quirements.
All neccessary approvals are needed from the local building ocials.
The data plate, which is located on the back of the stove, provides information regarding safety
testing information, name of certied testing laboratory, and installation requirements.
Installation requirements vary in dierent districts, and the local building ocials have the nal
authorization to approve your installation. You should discuss the installation with them before
beginning. Please ask your dealer for further information.
Do not connect to any air distribution duct or system.
Important: If the installation instructions are not followed carefully, it may cause dan-
gerous situations like chimney - and house res. Follow the instructions carefully and
do not deviate from them as it may cause injuries to people or property.
1.1 Checking loose parts in the stove
After unpacking, check that the center grate (in the centre of the re bed) and the re bricks
are rmly in position and have not shifted in transit. Check also that the air control works freely.
The stove is heavy and therefore it is strongly recommended that when lifting, it is under-
taken by two people.
Fitting instructions for Legs
Morsø 3112 B: After removing the outer packaging, atten it and lay onto the oor close to
the stove; this can then act as protective work surface during the assembly process.
Next, remove the legs and bolts from inside the stove. Gently lay the stove onto its back and
unscrew it from the wooden pallet. Using the bolts supplied, now screw the legs into position
on the underside of the base. The stove should now be lifted and moved into the upright posi-
tion, avoiding excess load on the back legs.
Morsø 3142 B: After removing the outer packaging, the stove should now be lifted
and moved into the position.
1.0 Installation of your Morsø stove

5
How to position the bae and access bae
Make sure that the upper bae plate (2) is located into its correct
position. It should be placed on top of the rear (xed) bae sec-
tion and secured into position against the 2 upstanding cast lugs.
Note: The access bae (3) must always be tted when the stove
is in use, as it not only assists the combustion process, but also
gives essential protection to the stove’s top plate.
Standard Accessories
Poker, ceramic ue connection gasket and riddling tool are standard
accessories, and can usually be found in the ashpan or rebox area.
1.2 The chimney / ue system
Note that the ue system must be independently secured and must
not rely on the stove for support.
The stove must not be connected to a chimney ue serving any other appliance.
(Several ues may run up a single chimney stack; use one ueway per appliance).
Use a residential type masonry or listed type HT factory-built chimney.
High Temperature (H.T.) Chimney Standard UL-103-1985 (2100º F.) for the USA, and High
Temperature (650ºC) Standard ULC S-629 for Canada.
The internal dimensions of the chimney connector and chimney must not be less than 6 inch-
es diameter (or equivalent cross section), and should not be signicantly larger than this. Too
large a section will tend to allow the ue gases to cool excessively, causing sluggishness or
unpredictability in the stove’s performance.
We recommend the length of the chimney system should be at least 16 feet (not required)
above the stove in normal domestic situations, measured from the ue collar to the top of
the chimney. Local conditions like for example - roof constructions, large trees nearby and
high altitude, may inuence the chimney draft and height. Therefore, contact the local pro-
fessional chimney sweep or your Morsø dealer.
Typical factory-built or masonry chimney installations