Motorola MBP846CONNECT User manual

User’s Guide
4.3" Wi-Fi® Video Baby Monitor
Models: MBP846CONNECT, MBP846CONNECT-2,
MBP846CONNECT-3, MBP846CONNECT-4
The features described in this User’s Guide are subject to modifications without prior notice.

Welcome...
to your new Motorola Digital Video Baby Monitor!
Thank you for purchasing the Digital Video Baby Monitor. Now you can see
and hear your baby sleeping in another room or you can monitor your older
children in their play room.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide a copy
of your dated sales receipt to confirm warranty status. Registration is not
required for warranty coverage.
For product-related questions, please call:
This User's Guide provides you with all the information you need to get the
most from your product.
Before you use the Digital Video Baby Monitor, we recommend that you
insert and fully charge the battery in the Parent Unit, so that it continues to
work if you disconnect it from the power supply. Please read the Safety
Instructions on pages 7 - 9 before you install the Units.
Got everything?
• 1 x Parent Unit
• 1 x Baby Unit (Camera)
• 1 x Power adapter for Parent Unit
• 1 x Power adapter for Baby Unit
In multi-camera packs, you will find one or more additional Camera Units
with power adapters.
[phone] (UK only)*
*Calls cost 7p per minute plus your telephone company's access charge
[phone] (ROI)

ENGLISH
Overview of the Parent Unit
1. Display (LCD screen)
2. VIDEO ON/OFF button V
Toggle to turn the LCD
screen ON/OFF
(Note: audio is maintained.)
3. TALK button T
Press and hold to speak to
your baby.
4. RESET button (recessed -
use small pin)
5. UP button +
Move Up menu options.
6. DOWN button -
Move Down menu options.
7. MENU button M
Press to open / close the
Menu options.
8. OK button O
9. Power Socket
10. LEFT button <
Move Left along menu
options.
11. RIGHT button >
Move Right along menu
options.
12. Charging LED:
BLUE when mains power
connected.
13. Parent Unit ON/OFF LED
(Green)
14. Audio Level LEDs (Green,
Amber, Red, Red)
15. Volume buttons
Press -/+ to decrease/
increase Volume level on
Parent Unit
16. Power button 0
Press and Hold to turn the
Parent Unit ON/OFF
17. Microphone
18. Stand
19. Speaker
20. Antenna
DC 5V
2
4
5
6
3
112
7
8
9
10
11
13 14 15 16
18
19
17
20

Parent Unit menu icons
Signal Level Indication (5 Levels)
Night Vision Mode (Video also changes to Black/White)
TTa lk M o d e O n
Volume Level Indication (4 Levels)
Panning Camera Left
Panning Camera Right
Tilting Camera Up
Tilting Camera Down
Zoom Level Control (1X, 2X)
Brightness Level Control (8 Levels)
Lullaby Control (5 Sound Selections)
Alarm Setting (6h, 4h, 2h, OFF)
On status bar, indicates alarm set, and when flashing, that alarm time has
been reached or missed.
Temperature scale select (oC / oF)
Readings display in BLUE, but turn RED if >29ºC / 84ºF, or <14ºC / 57ºF
Displays HH oC / oF if >36oC / 97oF.
Displays LL oC / oF if <1oC / 34oF.
Camera Control (scan , view , add , delete )
Set Screen Off Timer (Off , 5 min, 30 min, 60 min)
Indicates the screen off timer is set
Volume Level Control (8 Levels)
No Baby Unit detected
View multiple cameras on screen. Available when you have more than 1
Baby Unit (Camera).
+
V

Overview of Your Baby Unit
1. Photo Sensor (Night Vision Mode)
2. Camera Lens
3. Infrared LEDs (x 8, for night vision)
4. Power LED
On when linked to Parent Unit
Flashes when searching for Parent
Unit
5.
Microphone
6. Camera Battery LED
On when AC power is connected to
camera.
Flashes when the battery level of the
camera is low.
7. POWER ON/OFF switch
8. Temperature Sensor
9. Power Adapter Outlet
10. PAIR Button
11. Speaker
12. Star Grip or Tripod Mount
13. Antenna
Important guidelines for installing your Baby Monitor
• To use your Video Monitor Baby and Parent Units together, you must be able to
establish a radio link between them, and the range will be affected by environmental
conditions.
• Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or
reinforced concrete between the Baby and Parent Unit may block the radio signal.
• The signal strength may also be reduced by other solid structures, like walls, or by
radio or electrical equipment, such as TVs, computers, cordless or mobile phones,
fluorescent lights or dimmer switches.
• Use of other 2.4 GHz products, such as wireless networks (Wi-Fi
®
routers),
Bluetooth™ systems, or microwave ovens, may cause interference with this product,
so keep the Baby Monitor away at least 1 metre from these types of products, or turn
them off if they appear to be causing interference
• If the signal is weak, try moving the Parent and/or the Baby Unit to different positions
in the room(s).

6Table of contents
Table of contents
1. Safety Instructions..................................................................................... 7
2. Getting Started........................................................................................ 10
2.1 Baby Unit Power Supply............................................................................ 10
2.2 Parent Unit Battery Installation.................................................................. 11
2.3 Parent Unit Power Supply ......................................................................... 12
3. Using the Baby Monitor........................................................................... 13
3.1 Setting Up.................................................................................................. 13
3.2 Remote Pan ............................................................................................. 13
3.3 Night Vision Mode .................................................................................... 13
3.4 Talk Mode................................................................................................. 13
3.5 Video ON/Off ........................................................................................... 13
4. Parent Unit Menu Options ...................................................................... 15
4.1 Volume ..................................................................................................... 15
4.2 Digital Zoom and Tilt ................................................................................ 15
4.3 Brightness ................................................................................................. 15
4.4 Alarm ......................................................................................................... 15
4.5 Temperature ............................................................................................. 15
4.6 Camera Control ........................................................................................ 16
4.7 Power Saving Mode.................................................................................. 17
4.8 Audio Playlist ............................................................................................. 18
4.9 View Multi-Cameras on screen .............................................................. 19
5. Wi-Fi®Internet Viewing.......................................................................... 20
5.1 Minimum System Requirements .............................................................. 20
5.2 Getting Started - Connecting Devices..................................................... 21
5.3 User Account and Camera Setup on Android™ Devices....................... 22
5.4 User Account and Camera Setup on iPhone®/iPad®............................. 26
5.5 Camera Functions: ................................................................................... 32
5.6 Working with PC/Notebook .................................................................... 35
5.7 Procedure for Resetting the Camera ....................................................... 35
6. Disposal of the Device (Environment).................................................... 36
7. Cleaning .................................................................................................. 37
8. Help.......................................................................................................... 38
9. General Information ................................................................................ 45
10. Technical Specifications ......................................................................... 50
3.6 Temperature Display ............................................................................... 14

Safety Instructions 7
ENGLISH
1. Safety Instructions
WARNING :
Strangulation Hazard: Children have
STRANGLED in cords. Keep this cord out
of the reach of children (more than
1 m
away). Never use extension cords with AC
Adapters. Only use the AC Adapters
provided.

8Safety Instructions
WARNING
This Digital Video Baby Monitor is compliant with all relevant standards
regarding electromagnetic fields and is, when handled as described in the
User's Guide, safe to use. Therefore, always read the instructions in this User's
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This Digital Video Baby Monitor is not a substitute for responsible adult
supervision.
• Keep this user's guide for future reference.
• Keep the cords out of reach of children.
• Do not cover the Digital Video Baby Monitor with a towel or blanket.
• Test this monitor and all its functions so that you are familiar with it prior to
actual use.
• Do not use the Digital Video Baby Monitor in damp areas or close to water.
• Do not install the Digital Video Baby Monitor in extreme cold or heat, direct
sunlight, or close to a heat source.
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and battery pack.
• Only insert a battery pack of the same type.
• Do not touch the plug contacts with sharp or metal objects.
• Connect the power adapters to easily accessible mains power sockets.
CAMERA SET UP & USE:
• Choose a location for the Baby Unit that will provide the best view of
your baby in his/her cot.
• Place the Baby Unit on a flat surface, such as a dresser, bureau or
shelf, or mount the Baby Unit on a wall securely using the keyhole
slots in the underside of the stand.
• NEVER place the Baby Unit or cords within the cot.

Safety Instructions 9
ENGLISH
CAUTION
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
The Unit shall be setup and used so that parts of the user's body other than the
hands are maintained at a distance of approximately 20 cm (8 inches) or more.

10 Getting Started
2. Getting Started
2. Getting Started
2.1 Baby Unit Power Supply
1. Connect the small plug of the power adapter to the Baby Unit (camera) and
the other end to a suitable mains power socket.
NOTE
Only use the enclosed Power Adapter (5V DC / 1000mA).
2. Slide the POWER ON/OFF switch to the ON position to turn the Baby Unit
on.
3. Slide the POWER ON/OFF switch to the OFF position to turn the Baby
Unit off.

Getting Started 11
ENGLISH
2.2 Parent Unit Power Supply
IMPORTANT
The Parent Unit is assembled with a built-in rechargeable battery pack (Lithium
ion battery 2000mAh, to give up to 5 hours monitor operation), please charge it
for 16 hours before initial use. The battery is not a user-accessible item. Please
contact the helpline if you think it needs replacing.
1. Connect the DC plug of the power adapter to the Parent Unit and
the other end to a suitable mains power socket. Only use the enclosed
power adapter (5V DC / 1000mA) .
2. Press and hold the 0POWER ON/OFF button to switch ON the Parent
Unit.
3. Once the Baby and Parent Units are switched on, the display on the Parent
Unit will show the colour video captured by the Baby Unit, but if the baby's
room is dark, the video will display in black and white, with a icon
showing, due to the infra-red illumination by the Baby Unit.
4. If there is no connection or you are out of range, the video display will go
off, a symbol will appear on the screen, and the Parent Unit will beeps
continually. Move the Parent Unit closer to the Baby Unit until the link is re-
established.
5. Press and hold the 0POWER ON/OFF button, until the progress bar
finishes scrolling, to turn OFF the Parent Unit.
NOTE
The battery icon turns RED to indicate that the battery is low, and the
parent unit will beep every 15 seconds. The battery needs to be recharged; it
will take16 hours to charge fully.

12 Getting Started
When charging
1. If the Parent Unit is turned OFF with the adapter plugged in, a 2-pin plug
logo will appear on-screen for about 5 seconds, and then a flashing battery
logo will display for 15 seconds. The Blue LED at the top left will light up;
indicating that the adapter is plugged in and charging is continuing.
2. Whilst the power is ON, and the adapter is plugged in, the battery icon at
the top right corner of the screen will show that the battery is charging. The
Charging LED at the top left will light up to indicate that the adapter is
plugged in.
2.3 Registration (Pairing)
The Baby Unit is pre-registered to your Parent Unit. You do not need to register
it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the procedures
below:
1. Press the Mbutton of the Parent Unit and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted, and
the del/ add/ view/ scan menu will pop up.
3. Press the +UP button or -DOWN button to select
add , and press the
Obutton to confirm.
4. Camera will pop up, press the +UP button or -DOWN
button to select the desired Camera, and press the Obutton to start
searching for a camera unit, with "press PAIR on cam" shown.
Note: If a camera is currently paired with the Parent Unit, its camera
location (with a * against it) cannot be selected for a new registration.
5. Press and hold the PAIR button on the underside of the Baby Unit until the
Parent Unit finds the camera, beeps and PAIR OK appears on the screen.
The video from the camera will then appear.
NOTE
If a particular Baby Unit was registered previously, registering this current Baby
Unit again will cancel its old registration.
+
+
___

Getting Started 13
ENGLISH
3. Using the Baby Monitor
3.1 Setting Up
• Place the Baby Unit in a convenient location (e.g. on a table) and point the
camera lens towards the area you want to monitor.
• Adjust the angle of the Baby Unit's camera by using the pan and tilt function
from the Parent Unit, to move up, down, left and right until you are satisfied
with the image shown on the Parent Unit.
NOTE
Do not place the Baby Unit within the baby's reach! If there is interference with
the picture or sound, try moving the units to different locations, and ensure they
are not close to other electrical equipment.
3.2 Remote Pan
The camera can be remotely controlled from the Parent Unit when in a camera
viewing mode.
Press the <LEFT button or >RIGHT button to pan left or right.
3.3 Night Vision Mode
The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in
the dark. When the built-in photo sensor on the top of the Unit detects a low level
of ambient light, the LEDs will automatically activate and the screen on the
Parent Unit will display in black and white. The icon will be displayed at the
top of the screen.
3.4 Talk Mode
Press and hold the TALK button Ton the Parent Unit to talk to your baby through
the Baby Unit’s loudspeaker. The Ticon will be displayed at the top of the LCD
screen.
3.5 Video ON/OFF
Press VIDEO On/Off button to turn the LCD screen on or off, whilst still
leaving the audio monitor on.
V

14 Using the Baby Monitor
3.6 Temperature Display (HH °C / °F or LL °C / °F)
The temperature reading from the temperature sensor at the back of the Baby
Unit will be displayed at the top of the LCD screen in °C or °F (see section 4.5
“Temperature” for how to change). The readings will turn RED if the
temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will
change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading
will change to LL °C / °F if the temperature goes below 1°C / 34°F.

ENGLISH
4. Parent Unit Menu Options
4.1 Volume
1. Press the Volume button - or + to adjust the volume level, the icon will
pop up and you can select the desired volume from level 0~8. (The default
volume level setting is level 5, and level 0 is OFF .)
4.2 Digital Zoom and Tilt
1. Press the M button and the menu bar will pop up with highlighted.
2. Press the +UP button or -DOWN button to select 1X or 2X zoom. (The
default setting is
1X .)
4.3 Brightness
1. Press the M button and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted.
3. Press the +UP button or -DOWN button to select the desired brightness
from level 1 ~ 8. (The default brightness is level 4.)
4.4 Alarm
1. Press the M button and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted.
3. Press the +UP button or -DOWN button to select the alarm time (
6h , 4h ,
2h ), and the will turn on. (The default setting is Alarm OFF .)
4. If an alarm time is selected, the Parent Unit will beep for about 1 minute
after every 6, 4 or 2 hour period, and the will flash. Press any button to
stop the alarm.
3. When 2X isselected, pressthe + UPbutton or - DOWN button on the
left side of the Parent Unit to tilt the view up or down.
4.5 Temperature
1. Press the Mbutton and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted.
3. Press the +UP button or -DOWN button to select
°C or °F .
Parent Unit Menu Options 15

4.6 Camera Control
4.6.1 Add (pair) a camera
1. Press the M button and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted, and
the
del/ add/ view/ scan menu will pop up.
3. Press the +UP button or -DOWN button to select
add , and press the
Obutton to confirm.
4. Camera will pop up, press the +UP button or -DOWN
button to select the desired Camera, and press the Obutton to start
searching for a camera unit.
Note: If a camera is currently paired with the Parent Unit, its camera
location (with a * against it) cannot be selected for a new registration.
5. Press and hold the PAIR button on the underside of the Baby Unit until the
Parent Unit finds the camera, beeps and PAIR OK appears on the screen.
The video from the camera will then appear.
NOTE
A camera can only be registered to one Parent Unit at any one time.
4.6.2 View a camera
1. Press the M button and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted, and
the
del/ add/ view/ scan menu will pop up.
3. Press the +UP button or -DOWN button to select
view , and press
the Obutton to confirm.
4. Camera will pop up. Press the +UP button or -DOWN
button to select the desired camera, and press the Obutton to view the
picture from that camera.
Note: Only camera locations with a * can be selected.
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press the Obutton repeatedly to select the available Camera
options from .
+
+
___
+
___
, , , , .
16 Using the Baby Monitor

4.6.3 Delete a camera
1. Press the M button and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted, and
the
del/ add/ view/ scan menu will pop up.
3. Press the +UP button or -DOWN button to select
del , and press the
Obutton to confirm.
4. Camera will pop up, press the +UP button or -DOWN
button to select the desired Camera, and press the Obutton.
5. Press the +UP button or -DOWN button to select , then press the
O button to delete that registration.
NOTE
You are not allowed to delete the camera if there is only one registered camera
in the system.
4.6.4 Scan camera
This function is only available when you have more than 1 Baby Unit (Camera).
1. Press the Mbutton and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted, and
the
del/ add/ view/ scan menu will pop up.
3. Press the +UP button or -DOWN button to select
scan , and press the
Obutton to confirm.
4. The screen will then display images from different registered cameras in a
loop of Camera , changing about every 12 seconds.
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press the Obutton repeatedly to select the available Camera
options from .
+
___
+
___
, , , ,
4.7 Power Saving Mode
1. Press the Mbutton and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted.
3. Press the +UP button or -DOWN button to select auto video off after
5 mins, 30 mins or 60 mins if operating on batteries only.
NOTE
The audio will remain and you can press any key to switch the video back on.
V
ENGLISH
Parent Unit Menu Options 17

4.8 Audio Playlist
You can playback audio content - Lullabies, Soothing Sounds and Audio
Book (English only) on the Baby Unit. The audio content can be
downloaded and stored in the Baby Unit via Hubble App. You have 10
preloaded lullabies/soothing sounds and 10 audio books in the Baby
Unit.
4.8.1 Lullaby/Soothing Sounds Playback
• Tap on Mbutton then Scroll Left/Right to select option at the
menu bar.
• Scroll Up or Down to select then confirm with Obutton.
• Press +UP button or -DOWN button to view the desired Lullaby/
Soothing Sounds. The song name appears on the screen.
• Press Obutton to play the selection.
4.8.2 Audio Book (English only) Playback
• Tap on Mbutton then Scroll Left/Right to select option at
the menu bar.
• Scroll Up or Down to select then confirm with Obutton.
• Press +UP button or -DOWN button to view the desired Audio
Book. The book title appears on the screen.
• Press Obutton to play the selection.
4.8.3 Personal Audio Playback
• Tap on Mbutton then Scroll Left/Right to select option at
the menu bar.
• Scroll Up or Down to select then confirm with Obutton.
• Press +UP button or -DOWN button to view your personal
audio, the audio list appears on the screen.
• Press Obutton to play the selection.
NOTE
Before playback your personal audio, you are required to record your audio
following the instructions in Hubble for Motorola Monitors App.
18 Parent Unit Menu Options

4.9 View multiple cameras on screen
This function is only available when you have more than 1 Baby Unit (Camera).
When the Split Screen function is On, you can view multiple cameras on the
screen, although only hear audio from one screen at a time.
1. Press the Mbutton and the menu bar will pop up.
2. Press the <LEFT button or >RIGHT button until is highlighted.
3. Press the +UP button or -DOWN button to select Split Screen On /
Off .
4. When the Split Screen function is On, you can press the <LEFT button or
>RIGHT button/ +UP button or -DOWN button to switch between
cameras to hear the audio from the selected camera, indicated by the red
frame.
Note:
When in multi-screen mode the TALK button operates with the selected camera.
If you want to play a lullaby sound through a camera, you must set this before
selecting the multi-screen mode.
Zoom does not work in multi-screen mode.
ENGLISH
Parent Unit Menu Options 19

5. Wi-Fi®Internet Viewing
5.1 Minimum System Requirements
Web Portal
• Windows®7
• Mac OS®10.7
• Chrome™ 24
• Internet Explorer®9
• Safari®6
• Java™ 7
• Firefox®18.0
• Adobe®Flash®Player 15.0
Android™ System
• Version 5.0 or above
iPhone®/iPad®iOS
• Version 8.0 or above
High Speed (Wi-Fi®) Internet
• At least 0.6 Mbps upload bandwidth per camera (you can test your internet
speed on this site: http://www.speedtest.net)
20 Wi-Fi® Internet Viewing