Motorola RSVP User manual

1
User’s Guide
THE UNION OF
PAGING AND CELLULAR
TECHNOLOGIES
A
TM

2
INTRODUCTION
Your RSVP Numeric Display Pager turns any Motorola Micro-
TAC™ or retail pocket personal cellular telephone into the
ultimate personal communicator. RSVP also features a
removable and rechargeable, ultra-thin, Nickel-Metal-
Hydride cellular battery.
RSVP slides onto the back of your phone in place of the
existing battery unit, providing the control and convenience of
a pager and a phone in a single unit.
RSVP allows you to manage your cellular phone traffic, return
calls at your convenience, screen calls, extend phone battery
life, and even remain accessible while your phone is turned
off.
Paging Features Summary:
● Eight numeric message slots ● 12-digit numeric display
● Displays time of day ● Backlit display
● Message time stamping ● Musical alert
● Programmable alarm ● Vibrate or audible mode
● Retains messages while with reminder alert
turned off and when
replacing battery
Battery Features Summary:
●
Fits any Motorola
●
Battery is detachable
MicroTAC or retail pocket from pager unit
personal cellular telephone
●
Spare batteries are
●
Powerful and small enough to carry in
environmentally friendly a shirt pocket
Nickel-Metal-Hydride
●
One hour talk time,
battery eight hours standby
USINGTHIS GUIDE
This user’s guide describes the following:
● How to remove your ● Maintain your RSVP
cellular phone’s existing pager in top operating
battery condition
● Set up and operate your ● Use the RSVP cellular
pager battery and optional
charger adapter

3
PROCEDURE FOR CONNECTINGYOUR NEW
RSVP PAGERTOYOUR CELLULAR PHONE
Remove battery from any Motorola MicroTAC or retail pocket
personal cellular telephone in the following manner:
t
t
Press and
hold down
battery
release
Slide
battery
downward
against
stop
①
②
t
Lift battery
off cellular
phone
③

4
Note: Ensure the Nickel-Metal-Hydride battery is fully
charged and installed in the RSVP pager before performing
this procedure.
Install your RSVP pager in place of the cellular phone battery
in the following manner:
PAGING SERVICE ACTIVATION
Paging service providers require certain procedures for acti-
vating your RSVP pager. Contact your service provider to
activate paging service.
③
Slide RSVP
up until pager
into placesnaps
①②
Position RSVP
with display
end toward
phone
antenna
Set RSVP
onto mounting
slide approximately
one inch below
battery release

5
CONTROLS AND DISPLAY INDICATORS
The locations and descriptions of the RSVP pager controls
and display indicators are shown below:
Backlight/Reset
Button (●)
On/Read/
Select
Button
Alert/Backlight
Indicator
Battery Charger
/
Programmer
Contacts
(X)
(W)Menu/Lock
Button
Display
10:47a
[
\=
B
12:48p
1:
Message
Lock
Indicator
Alarm
Indicator
Alert
Mode
Indicator Continuing
Message
Indicator
Message
Slot
Number
Message
Time
Stamp
Time
of Day
Pager Display:

6
TURNINGYOUR PAGER ON
Press W to turn your pager on.Your pager will alert indicating
that it is on.
The time of day and the “Alert Mode” indicator, silent ( [ ) or
audible ( D ), is displayed.
READING MESSAGES
The RSVP pager can receive up to eight 20-character mes-
sages.When a message is received, the pager alerts with an
audible or a vibrate alert, and a flashing alert indication.
Press any button to stop the alert. Display your message as
follows:
1. Press the W button to display your message.
Messages that contain more than 12 characters are contin-
ued on a second screen.The ( B ) indicator means a second
screen exists.
2. Press W to advance to the second screen.If not selected,
the second screen is automatically displayed after one
minute.
The last screen of your message displays the message slot
number and the time the message was received.
If a message is left unread, the pager emits a reminder alert
every two minutes, and the number of unread messages is
displayed.
3. The pager automatically returns to the main status display
after approximately eight seconds.
TURNING ONTHE BACKLIGHT
In low light conditions, press ● on the display backlight.
Press ● again to turn off backlight or allow it to turn off auto-
matically.
RESET
Pressing the ● button twice always resets the pager back to
the main display menu.

7
CHANGING ALERT MODES
1. Press X . Either “Silent?” or “Audio?” is displayed,
depending on the current mode.
2 . To change the alert mode, press W .
For your pager to vibrate, it must be in the “silent” mode.
TURNINGYOUR PAGER OFF
1. Press X until the “PAGER OFF?” prompt is displayed.
2. Press W to turn the pager off.
With the pager off, the clock is shown on the display, but not
the “Alert Mode” indicator.
SETTINGTHE ALARM
Your pager’s alarm can be set to alert you to a certain time of
day. Set the alarm as follows:
1. Press X until “SET ALARM?”appears on your display.
2. Press W to select alarm on/off sequence.
3. To move to the next digit, press W .To advance through
each digit, press X . Repeat this process for each field
(On/Off, hours, minutes, AM/PM).
4. Press W to turn the alarm on or off.
5. Press the ● button twice to return to the main display
menu.
The \ indicator appears on the display when the alarm is
turned on. At the selected time, the alarm vibrates or emits a
unique 20-second alert and “ALARM” is displayed.
1. Press any button to stop the alarm alert.
SETTINGTHE TIME
Set the displayed time as follows:
1. Press X until “SETTIME?” is displayed.Then press W
once.
2. Press X until desired hour appears.
3. Press W to move to the next digit.
4. Repeat process for each field (hours, minutes, AM/PM).
5. Press the ● button twice to return to the main display
menu.

8
LOCKING AND UNLOCKING MESSAGES
Locked messages cannot be erased or overwritten by new
messages when memory is full. Also, they are not lost while
replacing the battery. Up to four messages may be locked at
one time.Lock your messages as follows:
1. Press X while reading your message. A lock
( L )
appears
on the display to indicate your message is protected.
2. To unlock your message, press X while reading the
locked message.
ERASING MESSAGES FROM MEMORY
1. Press X until “ERASE ALL?”appears on the display.
2. Press W .This erases all of your read-unlocked
messages.
The “ERASE ALL?”prompt is displayed if there are read-
unlocked messages in memory.
BATTERY FEATURES
The RSVP pager features a removable and rechargeable
Nickel-Metal-Hydride cellular battery unit. RSVP replaces
your cellular phone’s battery and provides charging contacts
in an identical location.Your existing cellular charger may be
used to charge your cellular/pager unit, or with the optional
adaptor, you may also charge a spare battery in your cellular
charger.

9
BATTERY REPLACEMENT
Remove RSVP from your cellular telephone and replace the
RSVP battery as shown below:
Install your new battery in the reverse order of removal.
P
ress release
t
hen slide pager
d
ownward away
f
rom antenna
①②Lift pager
away from
cellular
③
Release
Turn pager over,
insert tip of ball
pen under release
and pry up on
release, then lift
battery out of
pager

10
CHARGINGYOUR BATTERY
Your battery may be charged while attached to your cellular
phone or separately using the optional adapter shown in the
following illustration:
Refer to the charger manufacturer’s instructions for specific
use of your charger.
PROPER CARE
The RSVP pager is durable, reliable, and can provide many
years of dependable service, but it is a precision electronic
product.Water and moisture, excessive heat, and extreme
shock may cause damage to the pager. Avoid exposing your
pager to these conditions.
or
Charger has
two charging
locations
RSVP
battery Adapter
Cellular phone
with RSVP and
battery
Place battery
into adapter
and insert into
chargerRSVP
with
battery