Motorola Finiti HZ800 User manual

MOTOROLA and the Stylized M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings, LLC. All other product or
service names are the property of their respective owners. The Bluetooth
trademark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Motorola Mobility, Inc. is under license. © 2010 Motorola
Mobility, Inc. All rights reserved.
68014301063
motorola.com

MOTOROLA and the Stylized M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings, LLC. All other product or
service names are the property of their respective owners. The Bluetooth
trademark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Motorola Mobility, Inc. is under license. © 2010 Motorola
Mobility, Inc. All rights reserved.
68014301063
MOTOROLA HZ800
Quick Start Guide

1
Figure 1
2
3
4
67
8
9
5
1
Power
Switch
Off
On
Figure 2

2
Figure 3
Figure 4
Left
ear spring
Right
ear spring
Large
ear loop
Medium
ear loop
Small
ear loop

English
3
Welcome
Your MOTOROLA Finiti™ HZ800 headset delivers the best sound in any
condition and without raising your voice.
CrystalTalk™ dual microphones are used for everyday noise cancellation,
and the stealth mode for windy or extreme conditions.
Some other cool features:
• Simultaneous connect with two phones.
• Stream Bluetooth®music from your phone.
• Hear and reply to phone text messages with MotoSpeak™
• Hear the caller’s name and use your voice to answer or ignore calls
• Voice prompts to guide you on connections, battery level, and other
functions

English
4
Your headset
See figure 1 on page 1.
Take a moment to familiarize yourself with your headset.
1Charging port
2Call button
3Status light
4Stealth mode button
5 Volume buttons
6Ear loop
7Power switch
8Ear hook
9Ear piece with stealth mode sensor
Warning: do not apply pressure or squeeze the stealth mode sensor (small
rubber ballon), as it can damage the parts inside and will void the warranty.
Charge your headset
See figure 2 on page 1.
Indicator light
Red/yellow – Charging
Green – Fully charged
Note: Headset is not functional while charging.

English
5
A few basics to get you started
Choose an ear fitting
See figure 3 on page 2.
Your headset comes with multiple ear ttings: Left ear spring • Right ear
spring • Large ear loop • Medium ear loop • Small ear loop.
Choose your ear fitting (loop or spring) so your headset is comfortable.
1Lift the current ear fitting up and slide it off the headset in an upward
direction.
2Slide the new ear loop or spring downward onto the earpiece, then align
and push the bottom onto the groove.
Put your headset on
See figure 4 on page 2.
1Bend spring or loop on your headset.
2Insert headset earpiece into your ear canal.
3Ensure stealth mode sensor is in contact with your ear canal.
4Place spring or loop in bend of your ear.
5Flex the ear hook and loop over your ear. Point the headset microphone
towards your mouth.
Clean your headset
Keep your headset clean and dry. High humidity or perspiration can make the
ear fitting feel slippery. Remove the ear fitting and wipe it with a soft cloth to
remove dirt and moisture.
Note: Be very careful when wiping near the stealth mode sensor.
Turn your headset on & off
See figure 1 on page 1.

English
6
Pairing & connecting your headset
Pair & connect with your phone
1Turn off any Bluetooth devices previously paired with your headset.
2Turn on the Bluetooth feature on your phone.
3Put headset on your ear and turn it on.
The indicator light becomes steadily lit in blue and you hear “ready to pair”.
4Follow voice prompts to connect your phone to your headset.
5When prompted for the passkey, enter 0000.
When your headset successfully pairs with your phone, you hear “pairing
complete”. For daily use, make sure your headset is turned on, and
your phone’s Bluetooth feature is on. Your headset and phone connect
automatically.
Pair & connect a second phone
1Turn off first phone and any other Bluetooth devices previously paired
with your headset.
2Turn your headset off.
3Turn on the Bluetooth feature on your phone.
4Put headset on your ear and turn it on.
The indicator light becomes steadily lit in blue and you hear“ready to pair”.
5Follow voice prompts to connect your phone to your headset.
6When prompted for the passkey, enter 0000.
When your headset successfully pairs with your phone, you hear “pairing
complete”. To connect to both phones, simply turn on the first phone
while the second phone is connected. When you hear “<phone 1 name>
connected”, your headset is connected to both phones.
Test your connection
Place the headset on your ear and make a call from the phone. If your phone
and headset are successfully connected, you hear ringing on the headset.

English
7
Using your headset
Some features are phone/network dependent.
Function Action
Answer call Press the Call button or say “answer”
(only for 1st incoming call)
Reject call Press and hold a Volume button until you
hear a tone or say “ignore” (only for 1st
incoming call)
Make a voice dial call Press the Call button and you hear a tone
Redial last call Press and hold the Call button until you
hear a tone
Mute or unmute a call Press and hold both Volume buttons
End a call Press the Call button
Answer second incoming call Press the Call button
Reject second incoming call Press and hold a Volume button until you
hear a tone
Enable or disable stealth mode Press the stealth mode button
Tip: When connected to two phones, follow the voice prompts to perform
functions such as voice dial, redial, and end call on the desired phone.
Hear caller’s name
Note: This feature is phone dependent.
If your phone knows your caller’s name, then you hear “call from <name>”
on an incoming call.

English
8
Enabling stealth mode
Always be heard during calls with the CrystalTalk dual microphones and the
stealth mode sensor:
• CrystalTalk is the default mode and is always active to cancel out everyday
background noise
• Stealth mode can be activated when noise and wind reach extreme levels
to seal off all background noise
Press the stealth mode button and listen for the “stealth mode on” or
“stealth mode off” prompt.
Note: It is normal for the sound of your voice to be less “natural” in stealth
mode.
Listen to music
Note: This feature is phone dependent.
Your headset allows you to stream Bluetooth music from your phone. Music
playback is started and controlled from your phone.
While a call is active, music pauses. When the call ends, music resumes
playing.
Changing some settings
Press and hold the Call button while turning on the headset to turn these
features on/off:
• Reset to factory default
Caution: This action erases all pairing information stored in your headset.
• Caller ID
• Voice prompts
• Multipoint (two phone) connections
Follow the voice prompts to make changes to these settings.

English
9
Status indicators
Battery check
Press and hold both Volume buttons while not on a call.
Indicator light Voice prompt Talk time
Red “battery level is low” Less than 1.5 hours
Yellow “battery level is medium” Between 1.5 to 3.5 hours
Green “battery level is high” More than 3.5 hours
To save battery power, turn off the headset when you don’t use it for a
extended time.
Operating status
Indicator light Status
3 blue flashes Powering on/off
Steady blue Pairing/connect mode
Rapid blue/purple flashes Connection successful
Quick blue flash Incoming/outgoing call on phone 1
Quick purple flash Incoming/outgoing call on phone 2
Slow blue pulse Connected (on a call)
Slow blue flash Standby (connected to one phone)
Slow green flash Standby (connected to two phones)
Slow red flash Idle (not connected to a phone)
Slow purple pulse Connected call muted
Steady red Attempting to connect
Quick red flash Low battery
Note: After 1 minute on a call on a call or 20 minutes of inactivity, the light
stops flashing to conserve power, but the headset remains on.

English
10
Troubleshooting
My headset will not enter pairing mode.
Make sure that any devices previously paired with the headset are turned
off. If the indicator light is not steadily lit in blue, turn off both the other
device and headset, wait for 10 seconds, then turn headset back on. Wait
for the status light to become steadily lit in blue, indicating the headset is
now in pairing mode.
My phone doesn’t find my headset when searching.
Make sure the indicator light on your headset is steadily lit in blue when your
phone is searching for devices. If not, press and hold the Call button and both
Volume buttons until you “ready to pair” and see the indicator light lit in blue.
My headset worked before but now it’s not working
Make sure your phone is on and the Bluetooth feature is turned on in
your phone. If the Bluetooth feature was turned off or was turned on only
temporarily, you may need to restart the Bluetooth feature and pair your
phone and headset again.
The person you are talking to does not hear you
Try rotating the headset in your ear until optional sound is achieved. Also,
you can switch to another ear fitting to provide a better fit and performance.
The person you are talking to does not hear you in stealth mode
Make sure the ear fitting is clean and dry.
If you have any additional questions, please call your hotline number
(0870-9010-555) or visit us at www.hellomoto.com.

English
11
European Union Directives Conformance Statement
Hereby, Motorola Mobility Inc. declares that this product is in compliance with:
• The essential requirements and other relevant provisions of
Directive 1999/5/EC
• All other relevant EU Directives
You can view your product’s Declaration of Conformity (DoC) to Directive
1999/5/EC (the R&TTE Directive) at www.motorola.com/rtte.
Caring for the Environment by Recycling
When you see this symbol on a Motorola product, do not dispose of
the product with household waste.
Recycling Mobile Phones and Accessories
Do not dispose of mobile phones or electrical accessories, such as
chargers or headsets, with your household waste. In some countries or
regions, collection systems are set up to handle electrical and electronic
waste items. Contact your regional authorities for more details. If collection
systems aren’t available, return unwanted mobile phones or electrical
accessories to any Motorola Approved Service Centre in your region.
FCC Notice to Users
FCC Notice The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC logo, and/or an
FCC ID in the format FCC-ID:xxxxxx on the product label.
Motorola has not approved any changes or modifications to this device by
the user. Any changes or modications could void the user’s authority to
operate the equipment. See 47 CFR Sec. 15.21.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. See 47 CFR Sec.
15.19(3).

English
12
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Approved Accessories
Use of accessories not approved by Motorola, including but not limited to
batteries, antennas, and convertible covers, may cause your mobile device
to exceed RF energy exposure guidelines and may void your mobile device’s
warranty.
Motorola recommends that you always use Motorola-branded chargers.
Motorola devices are designed to work with Motorola chargers.
For approved Motorola accessories, visit our Web site at: www.motorola.com
Use & safety for battery-powered accessories
Your battery is designed to last the life of the product. It should only be
removed by a recycling facility. ANY ATTEMPT TO REMOVE OR REPLACE
YOUR BATTERY WILL DAMAGE THE PRODUCT.
• Battery life may temporarily shorten in low-temperature conditions (-10°C
for storage/use below 0°C for recharge) or permanently reduce in high
temperature conditions (above 60°C for storage/use or above 45°C for
recharge).

English
13
• Do not let your mobile device get wet.
• Do not store your accessory in a parked car or direct sunlight.
WARNING: MAY EXPLODE IF DISPOSED OF IN FIRE.
Driving Precautions
Check and obey the laws and regulations on the use of mobile devices in the
area where you drive. The use of wireless devices and their accessories in
your area may be prohibited or restricted. The use of wireless phones while
driving may cause distraction. Discontinue a call if you can’t concentrate on
driving. When using your mobile device while driving, please:
• Give full attention to driving and to the road.
• Use your hands-free solution to perform hands-free calls.
• Pull off the road and park before making or answering a call if driving
conditions so require.
Caution about high volume usage
Warning: Exposure to loud noise from any source for extended periods of
time may temporarily or permanently affect your hearing. The louder the
volume sound level, the less time is required before your hearing could be
affected. Hearing damage from loud noise is sometimes undetectable at first
and can have a cumulative effect. To protect your hearing:
• Start your volume control at a low setting and use as low a volume as
possible.
• Limit the amount of time you use headsets or headphones at high volume.
• Where possible, use your headset in a quiet environment with low
background noise.
• Avoid turning up the volume to block out noisy surrounding.
• Turn the volume down if you can’t hear people speaking near you.
If you experience hearing discomfort, including the sensation of pressure or
fullness in your ears, ringing in your ears, or muffled speech, you should stop
listening to the device through your headset or headphones and have your
hearing checked by your doctor.

Français
14
Bienvenue
Votre oreillette Motorola Finiti™ HZ800 vous permet d’obtenir la meilleure
qualité sonore en toutes circonstances, sans avoir besoin d’élever la voix.
Les deux micros CrystalTalk™ permettent l’annulation du bruit ambiant, et le
mode isolement est très efficace en cas de vent ou dans un environnement
très bruyant.
Quelques fonctions supplémentaires très utiles :
• Écoutez vos SMS et répondez-y grâce à MotoSpeak™.
• Vous pouvez entendre le nom de l’appelant et utiliser la commande vocale
pour accepter ou ignorer les appels.
• Streamer des talkshows, des chansons ou des livres audio stockés sur
votre téléphone Bluetooth®.
• Des commandes vocales vous donneront des informations concernant les
connexions, le niveau de la batterie et les autres fonctions.
• Il est possible de se connecter à deux téléphones en même temps et de
passer d’un téléphone à l’autre même en cours de conversation.

Français
15
Votre oreillette
Voir figure 1, page 1.
Prenez le temps de vous familiariser avec votre oreillette.
1Port de charge
2 Touche d’appel
3 Diode
4Touche mode isolement
5Touches de volume
6Support oreille
7 Bouton marche/arrêt
8 Tour d’oreille
9 Écouteur et capteur du mode isolement
Avertissement : veillez à ne pas exercer de pression sur le capteur de mode
isolement (petit capuchon en caoutchouc), car cela pourrait endommager
les pièces qu’il renferme et annuler la garantie.
Charge de votre oreillette
Voir figure 2, page 1.
Diode :
Rouge/jaune – Charge en cours
Vert – Charge terminée
Remarque : il est impossible d’utiliser l’oreillette pendant la charge.

Français
16
Quelques bases pour commencer
Choix du type de support
Voir figure 3, page 2.
Plusieurs types de supports sont fournis avec votre oreillette : Coussinet
« tige » pour oreille gauche • Coussinet « tige » pour oreille droite • Coussinet
« anneau », taille large • Coussinet « anneau », taille moyenne • Coussinet
« anneau », petite taille.
Choisissez le support (coussinet « tige » ou « anneau ») qui vous apporte le
plus grand confort.
1 Soulevez le support en place sur l’oreillette et tirez-le vers le haut pour
le détacher.
2Insérez le nouveau support en le poussant vers le bas et fixez-le en
exerçant une pression.
Mise en place de l’oreillette
Voir figure 4, page 2.
1 Recourbez le coussinet « tige » ou «anneau » sur l’oreillette.
2 Placez le haut-parleur (écouteur) à l’extérieur de votre conduit auditif.
3Assurez-vous que le capteur du mode isolement soit en contact avec le
conduit auditif.
4 Placez la tige ou l’anneau du coussinet dans le creux de l’oreille.
5 Pliez le tour d’oreille et accrochez-le à votre oreille. Orientez le microphone
de l’oreillette vers votre bouche.
Nettoyage de l’oreillette
Veillez à ce que votre oreillette reste propre et sèche. L’humidité ou la
transpiration peuvent rendre le support glissant. Enlevez le support et
nettoyez-le avec un tissu léger pour enlever la saleté et l’humidité.
Remarque : Faites très attention lorsque vous nettoyez le capteur du mode
isolement.
Mise en marche / arrêt de l’oreillette
Voir figure 1, page 1.

Français
17
Couplage et connexion de votre oreillette
Couplage et connexion de votre téléphone
1 Éteignez tous les périphériques Bluetooth précédemment couplés avec
votre oreillette.
2 Activez l’option Bluetooth de votre téléphone.
3 Placez l’oreillette sur votre oreille, puis mettez-la en marche.
La diode reste allumée en bleu et vous entendez « prêt pour le couplage»
4 Suivez les commandes vocales pour connecter votre téléphone à votre
oreillette.
5 Lorsque vous êtes invité à saisir le code, saisissez 0000
Une fois le couplage réussi, vous entendez le message « couplage terminé »
Pour une utilisation régulière, assurez-vous que votre oreillette est
allumée et que l’option Bluetooth de votre téléphone est activée. Votre
oreillette et votre téléphone se connectent alors automatiquement.
Couplage et connexion d’un second téléphone
1 Éteignez d’abord votre téléphone et tous les périphériques Bluetooth
précédemment couplés avec votre oreillette.
2 Éteignez votre oreillette.
3 Activez l’option Bluetooth de votre téléphone.
4 Répétez les étapes 3 à 5 telles qu’expliquées dans la section précédente.
Test de votre connexion
Placez l’oreillette sur votre oreille et passez un appel depuis votre téléphone.
Si votre téléphone et votre oreillette sont correctement connectés, une
sonnerie retentit dans l’oreillette.