Motorola H520 User manual

Quick Start Guide
MOTOROLA
H520

1
your headset
charge it
pair & connect
put it on
turn on & off
battery check
calls
status indicators
restore headset
troubleshooting
Safety & General Information
FCC Notice to Users
European Union Directives
Conformance Statement
Contents
2
3
4
6
9
10
11
13
16
17
19
23
34

2
Take a moment to familiarize yourself with your new H520 Headset.
your headset
Earhook
Charging
Port
Ear
Speaker
Indicator
Light
Microphone
Power
Switch
Call
Button
Volume
Buttons

3
charge it
The indicator light is red or purple while the battery is charging. When the battery
is fully charged, the indicator light turns blue.
Note: Before rst time use, leave headset charging overnight.
Note: Headset is not functional while charging.
Note: Your battery is designed to last the life of your product. It should only be
removed by a recycling facility. Any attempt to remove or replace your battery will
damage your headphones.
You’ll need to charge your headset overnight before using it. Plug the charger into
the charging port on your headset and a wall outlet.

4
pair & connect
Let’s get your headset paired and connected to your Bluetooth phone.
Turn off any Bluetooth devices previously paired with your headset.
Turn on the Bluetooth feature on your phone.
Turn on your headset (see page 9 for help).
The indicator light becomes steadily lit in blue.
Set your phone to search for Bluetooth devices.
Select Motorola H520 from the search results on your phone.
Select Ok or Yes to pair your headset with your phone.
Note: When prompted for the passkey, enter 0000.
The indicator light rapidly ashes blue and purple to indicate successful pairing
and connecting with your phone.
pair & connect

5
reconnect
After initially pairing and connecting your phone and headset, you don’t need to
do it again.
For daily use, make sure your headset is turned on, and your phone’s Bluetooth
feature is on. Your headset and phone will connect automatically!
test your connection
Place the headset over your ear.
On the phone, dial a number and press Call/Send key.
If your phone and headset are successfully connected, you hear ringing on the
headset.
pair & connect

6
You can wear your headset using either an earhook or ear cushion.
wear with earhook
Remove and install all the supplied earhooks to nd a good t.
Your headset comes ready for your right ear. To change for your left ear:
put it on
1 2
From Right Ear To Left Ear

7
put it on
wear with ear cushion
Remove earhook from headset.
Flex the earhook and loop it over your ear.

8
turn on & off
put it on
Try out all the supplied ear cushions to get a good t.
set volume buttons
Turn the headset power off.
Press and hold the Volume button you want to assign as the "volume up"
button and slide the Power switch on. The indicator light ashes blue three
times. When connected, it will ash blue/purple.
Volume
Buttons
Indicator
Light

9
turn on & off
turn on
Slide the Power switch to the on position (no red is shown under the switch).
The indicator light flashes blue three times, then flashes in blue and purple (if
connected with a device) or is steadily blue (if ready to be paired).
turn off
Slide the Power switch to the off position (red is shown under switch). The
indicator light ashes three times then turns off.

10
indicator light
red
purple
blue
available talk time
less than 1.5 hours
between 1.5 to 3.5 hours
up to 5 hours
battery check
Press and hold both Volume buttons while not on a call.
To save battery power, turn off the headset when you don't use it for an extended
time.

11
battery check
calls
TO…
answer call
mute or unmute a call
reject call
end a call
redial last call
make a voice dial call
answer or reject
second incoming call
Press the Call button.
Press both Volume buttons.
Press and hold a Volume button until you
hear a tone.
Press the Call button.
Press and hold the Call button until you
hear two tones.
Use phone to answer/reject second call
(follow your phone’s instructions)
Press the Call button and wait for voice
prompt.
calls

12
calls
Note: Your H520 supports both Handsfree and Headset Proles. Accessing call
functions depends upon which profile your phone supports. See your phone's
user's guide for more information.
Note: Some features are phone/network dependent.

13
calls
red
purple
blue
charging (battery level less than 50% charge)
charging (battery level more than 50% charge)
charging complete
headset indicator headset status
status indicators
headset indicator headset status
off power off
three blue ashes powering on/off
steady blue pairing/connect mode
indicator light (with charger plugged in)
indicator light (with charger not plugged in)

14
status indicators
headset indicator headset status
rapid blue/purple ashes connection successful
quick blue ash incoming/outgoing call
slow blue pulse connected (on a call)
slow blue ash standby (not on a call)
slow red ash idle (not connected to a phone)
steady red attempting to connect
quick red ash low battery
slow purple pulse connected(call muted)
Note: After 20 minutes on a call or of inactivity, the light stops flashing to
conserve power, but the headset remains on.

15
status indicators status indicators
audio tones
audio tone headset status
ascending tone powering on
two descending tones powering of
ring tone incoming call
two short tones when
pressing Volume button
volume at maximum or minimum
high/low tones repeated
every 60 seconds
low battery
two rapid descending tones mute disabled
low tone every 10 seconds mute reminder
no audio indications;
deteriorating quality
out of range
three ascending tones connected to phone
two rapid ascending tones mute enabled

16
restore headset
Caution: This action erases all pairing information stored in your headset.
To restore your headset to original factory settings, with the headset turned on,
press and hold both Volume buttons and Call button for 10 seconds until the
indicator light is steady blue.

17
restore headset troubleshooting
My headset will not enter pairing mode.
Make sure that any devices previously paired with the headset are turned off.
If the indicator light is not steadily lit in blue, turn off both the other device and
headset, wait 10 seconds, then turn headset back on. Wait for the indicator light
to become steadily lit in blue, indicating the headset is now in pairing mode.
My phone doesn't nd my headset.
Make sure the indicator light on your headset is on (lit in blue) and steady when
your phone is searching for devices.
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is turned on in your phone.
If the Bluetooth feature was turned off or was turned on only temporarily, you may
need to restart the Bluetooth feature and pair your phone and headset again (see
“pair & connect” on page 4).

18
Support.
If you need more help, contact us at 1-877-MOTOBLU or visit us at
www.motorola.com/Bluetoothsupport or www.motorola.com/bluetoothconnect .
troubleshooting

19
Safety & General Information
032374o
Symbol Denition
Important safety information follows.
Do not let your battery, charger, or mobile device get wet.
IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ
THIS INFORMATION BEFORE USING YOUR DEVICE.
Approved Accessories
Use of accessories not approved by Motorola, including but not limited to
batteries, antennas, and convertible covers, may cause your mobile device
to exceed RF energy exposure guidelines and may void your mobile device’s
warranty. For a list of approved Motorola accessories, visit our Web site at:
www.motorola.com.
Batteries & Chargers
Your battery, charger, or mobile device may contain symbols, dened as follows:
troubleshooting