Motorola H390 - Headset - In-ear ear-bud User manual

Quick Start Guide
Motorola H390
/ 快速使用手册

1
BEFORE YOU BEGIN
1CHARGE Your Headset's Battery
2START BLUETOOTH FEATURE Your Phone
3PAIR Your Headset
3PAIR
CONTINUED
Your Phone
4TEST AND USE
USING YOUR H390
TURNING HEADSET ON AND OFF
EARBUDS AND YOUR HEADSET
WEARING THE HEADSET
CHANGING FOR USE ON OTHER EAR
CHANGING VOLUME BUTTON ORIENTATION
QUICK BATTERY CHECK
MAKING CALLS
INDICATOR LIGHT
AUDIO TONES
TROUBLESHOOTING
European Union Directives Conformance Statement
Contents
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
22

2
BEFORE YOU BEGIN
Before using this product, read the Important Safety and Legal Information pamphlet and follow its
instructions.
Take a moment before you get started to familiarize yourself with your new H390
Headset.
Call Button
Indicator Light
Volume
Buttons Earhook
Power Switch
Microphone
Speaker

3
Verify slide switch is in the off position (toward the charging port).
Plug the Motorola charger into the end of the headset.
The indicator light turns red or yellow when the battery is charging. It may take
up to 1 minute for the indicator light to turn on. When the headset’s battery is
fully charged (about 2 hours), the indicator light turns green.
Disconnect the charger.
1 CHARGE Your Headset’s Battery
1
2
3
Note: Headset is not functional while charging.
Note: This product uses a lithium ion, rechargeable, non-replaceable battery. Under normal use, the
expected life of the rechargeable battery is approximately 400 charges.
Charging
Port

4
Press (Menu) > Settings > Connection > Bluetooth Link > Setup.
Scroll to Power.
Select Change.
Scroll to On.
Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones. For other phones, see your phone’s
user’s guide.
2 START BLUETOOTH FEATURE Your Phone
Your phone’s Bluetooth feature is off by default. To use your headset, you must turn
on the Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
1
2
3
4
5

5
3 PAIR Your Headset
Before you can use your headset, you must pair (link) it with your phone.
Step A - ENSURE HEADSET IS IN PAIRING MODE
Power on headset by sliding the Power switch towards the microphone to initiate
easy pairing. After a few moments, the indicator light will be steadily lit in blue to
indicate headset is in pairing mode.
Indicator Light
(steadily blue for
pairing)
If the headset does not enter pairing mode, see TROUBLESHOOTING for help.
Power Switch

6
On your Motorola phone, press (Menu) > Settings > Connection > Bluetooth
Link > Handsfree > Look for Devices.
The phone lists Bluetooth devices it finds.
Select Motorola H390.
Select OK or Yes to pair your headset with your phone.
Enter the passkey: 0000
Select OK.
When your headset successfully pairs and connects with your phone, the
indicator light changes from steadily lit to flashing blue and purple.
Note: These steps are for most Motorola phones. For other phones, see your phone’s user’s
guide.
3 PAIR CONTINUED Your Phone
Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET
For most Motorola phones:
1
2
3
4
5

7
Place the headset over your ear.
On the phone, dial the number you want to call and press SEND key on your
phone.
If your phone and headset are successfully paired, you will hear ringing on the
headset.
After you have successfully paired your phone and headset, you don’t need to
repeat these steps. For daily use, ensure that your headset is turned ON and
that your phone’s Bluetooth feature is ON.
4 TEST AND USE
Your phone and headset are now paired and ready to make and receive calls.
To make a call:
1
2

8
USING YOUR H390
Note: If desired, your headset can be restored to original factory settings. This action will erase
all pairing information stored in your headset. Thus, you will need to pair your phone and headset
again (see step 3).
Note: To restore your headset to original factory settings, press and hold both Volume buttons and
the Call button at the same time for 10 seconds.

9
TURNING HEADSET ON AND OFF
To turn your headset on, slide the switch toward the microphone. The indicator
light flashes blue three times, then flashes in blue and purple (if connected with a
device) or is steadily blue (if ready to be paired).
To turn your headset off, slide the switch toward the charging plug. The indicator
light flashes three times then turns off.
Power Switch
Indicator
Light