Moxa Technologies CSM-G200 Series User manual

P/N: 1802002002021
*1802002002021*
CSM-G200 Series
Quick Installation Guide
Version 1.1, July 2022
Technical Support Contact Information
www.moxa.com/support
2022 Moxa Inc. All rights reserved.

- 2 -
Overview
Introduction
The CSM-G200 Series is a Gigabit Ethernet to optical fiber slide-in
media converter module and is part of the NRack System. It provides
Ethernet media conversion from 10/100/1000 BaseT(X) to 100/1000
BaseFX (SFP slot) and can be installed in every chassis of the NRack
System.
The CSM-G200 Series includes the following models:
•CSM-G200-1221: 10/100/1000BaseT(X)-to-100/1000BaseSFP
slide-in media converter module
Installation
The CSM-G200 media converter slide-in module can be hot-swapped,
which means the chassis does not need to be powered off or removed
during installation. Align the slide-in module with the chassis
installation slot so that the panel fastener screw is at the top of the
module. Carefully slide the slide-in module into the slot while aligning
the module’s circuit board with the installation guide.
Ensure that the slide-in module is firmly seated inside the chassis. Push
in and rotate the attached panel fastener screw clockwise to secure the
module to the chassis.
Why Convert Ethernet to Fiber
Fiber communication not only extends the communication distance but
also provides many helpful features.
•IMMUNITY FROM ELECTRICAL INTERFERENCE:
Electromagnetic interference or radio frequency interference does
not affect fiber. Thus, fiber provides a clean communication path
and is immune to cross-talk.
•INSULATION:
Optical fiber is an insulator; the glass fiber eliminates the need for
using electric currents as the communication medium.
•SECURITY:
Conventional electric means cannot tap fiber. Furthermore, fiber is
very difficult to tap into optically. Radio and satellite communication
signals can be captured easily for decoding.
•RELIABILITY & MAINTENANCE:
Fiber is immune to adverse temperature and moisture conditions,
does not corrode or lose its signal, and is not affected by short
circuits, power surges, or static electricity.

- 3 -
Features
•LFP (Link Fault Pass-through)
•FEF (Far End Fault)
•Two different operation modes
Store-and-forward
Pass-through
•Auto negotiation
•Plug and play
•Hot-swap
•Jumbo frame
Package Checklist
Moxa’s CSM-G200 Series is shipped with the following items.
•CSM-G200 slide-in media converter module
•Quick installation guide (printed)
•Warranty card
NOTE: Please notify your sales representative if any of the above items
are missing or damaged.
Dimensions
CSM-G200-1221

- 4 -
Electrostatic Discharge Warning!
To protect the product from damage due to electrostatic
discharge, we recommend that you wear a grounding device
when handling your CSM-G200 slide-in modules.
Communication Connections
The CSM-G200 Series has one 10/100/1000BaseT(X) Ethernet port and
one 100/1000BaseFX (SFP slot) fiber port.
RJ45 Ethernet Port Connection
The CSM-G200 has a 10/100/1000BaseT(X) Ethernet port located on
the front panel to connect to Ethernet-enabled devices.
When connected to a 10/100 Mbps Ethernet port, the pinouts and cable
wiring diagrams for both the MDI (NIC-type) and MDI-X (HUB/switch-
type) ports for both straight-through and crossover Ethernet cables
are:
MDI Port Pinouts
MDI-X Port Pinouts
8-pin RJ45
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Signal
1
Rx+
2
Rx-
3
Tx+
6
Tx-
RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring
RJ45 (8-pin) to RJ45 (8-pin) Crossover Cable Wiring

- 5 -
1000BaseT(X) Ethernet Port Connection
1000BaseT(X) data is transmitted on differential TRD+/- signal pairs
over copper wires. When connected to a 1000 Mbps Ethernet port, the
pinouts and cable wiring diagrams for both the MDI (NIC-type) and
MDI-X (HUB/switch-type) ports for both straight-through and crossover
Ethernet cables are:
MDI/MDI-X Port Pinouts
Pin
Signal
1
TRD (0) +
2
TRD (0) -
3
TRD (1) +
4
TRD (2) +
5
TRD (2) -
6
TRD (1) -
7
TRD (3) +
8
TRD (3) -
1000BaseSFP Fiber Port Connections
The Gigabit Ethernet ports on the CSM-G200 are 1000BaseSFP Fiber
ports, which require using Gigabit mini-GBIC fiber transceivers to work
properly.
The concept behind the LC port and cable is straightforward. Suppose
you are connecting devices I and II. Contrary to electrical signals,
optical signals do not require a circuit to transmit data. One of the
optical lines is used to transmit data from device I to device II, and the
other optical line is used to transmit data from device II to device I for
full-duplex transmission.
Remember to connect the Tx (transmit) port of device I to the Rx
(receive) port of device II, and the Rx (receive) port of device I to the
Tx (transmit) port of device II. If you are making your own cable, we
suggest you label the two sides of the same line with the same letter
(A-to-A and B-to-B, as shown below).
ATTENTION
The CSM
-G200 is only compatible with transceiver modules
from Moxa's SFP
-1G Series and SFP-1FE Series. If you are
using t
he SFP-1FESLC-T, SFP-1FELLC-T, or S FP-1FEMLC-T, use
version V1.3 or above to ensure that the CSM
-G200 media
converter functionality works properly.

- 6 -
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing
serious
damage to your eyes, do not stare directly into the laser beam.
DIP Switch Settings
DIP
Function
ON (Default)
OFF
1
Force Fiber Speed
Auto
1000 Mbps
2
TP Auto Negotiation
Enable
Disable
3
Force TP Speed
1000 Mbps
100 Mbps
4
Force TP Duplex
Full-duplex
Half-duplex
5
Link Fault Pass-through
Enable
Disable
6
Operating Mode
Store-and-forward
Pass-through
7
Jumbo Frame
Disable
Enable
LED Indicators
LED
Color
State
Function
PWR Green
On
Power is being supplied to power
input.
Off Power is not being supplied to power
input.
FAULT Red
On
Communication failed
Blinking
The device is unable to initialize
successfully
Off
Data is transferring normally
G2 Green
On
FX port’s is active.
Blinking
Data is being transmitted
Off
FX port is inactive.
10/100M (TP) Yellow
On
TP port’s 10/100 Mbps is active.
Blinking
Data is being transmitted at 10/100
Mbps.
Off
TP port’s 10/100 Mbps is inactive.
1000M (TP) Green
On
TP port’s 1000 Mbps is active.
Blinking
Data is being transmitted at 100
Mbps.
Off
TP port’s 1000 Mbps is inactive.
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect the Moxa CSM-
G00’s 10/100/1000BaseT(X) ports to any kind of Ethernet device,
regardless of the type of Ethernet cable used for the connection. This
means that you can use either a straight-through or crossover cable to
connect the CSM-G200 to Ethernet devices.

- 7 -
Auto-Negotiation and Speed Sensing
All the CSM-G200’s RJ45 Ethernet ports independently support auto-
negotiation for transmission speeds of 10 Mbps, 100 Mbps, and 1000
Mbps in operations, according to the IEEE 802.3u standard.
This means that some nodes could operate at 10 Mbps, while other
nodes are operating at 100 Mbps or 1000 Mbps. Auto-negotiation takes
place when an RJ45 cable connection is made, and then each time a
LINK is enabled. The CSM-G200 indicates its capability for using 10
Mbps, 100 Mbps, or 1000 Mbps transmission speeds; the device at the
other end of the cable is expected to indicate similarly.
Depending on what type of device is connected, this will cause an
agreement to operate at a speed of 10 Mbps, 100 Mbps, or 1000 Mbps.
If the CSM-G200’s RJ45 Ethernet port is connected to a non-negotiating
device, it will default to a speed of 10 Mbps and half-duplex mode, as
required by the IEEE 802.3u standard.
Specifications
Physical Characteristics
Housing
SPCC
Dimensions
86.8 x 124.3 x 21 mm (3.42 x 4.89 x 0.83 in)
Environment Limits
Operating
Temperature
0 to 55°C (32 to 131°F)
Storage
Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)
Power Requirements
Input Voltage
12 VDC
Power Consumption
2.23 Watts
Regulatory Approvals
EMC
CE, FCC
EMI CISRP 32
CISRP 35
EMS IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m;
Signal: 3 V/m
IEC 61000-4-8 PFMF: 30 A/m
Warranty
Warranty Period
5 years
Details
See www.moxa.com/warr anty
사용자안내문
이
기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은 기기로서
가정용
환경에서 사용하는 경우 전파간섭의 우려가 있습니다.