Moxa Technologies WAPN008-1 User manual

Moxa 2.4/4.9/5 GHz
WAPN008-1 User’s Manual
www.moxa.com
First Edition, May 2019
2019 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.

WAPN008-1 User’s Manual
The hardware and software described in this manual is furnished under a license agreement and may be used
only in accordance with the terms of that agreement.
Copyright Notice
Copyright 2019 Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of Moxa.
Moxa provides this document “as is,”without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to
the information herein to correct such errors, and these changes are incorporated into new editions of the
publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: [phone]
Fax: [phone]
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: [phone]
Fax: [phone]
Moxa Europe:
Tel: [phone]
Fax: [phone]
Moxa Asia-Pacific:
Tel: [phone]
Fax: [phone]

Table of Contents
Chapter 1 Introduction
Overview
Specification
Chapter 2 Getting Started
Module Layout
Block Diagram
Hardware Installation
Software Installation

WAPN008-1 User’s Manual Introduction
1
Chapter 1 Introduction
The following topics are covered in this chapter:
Overview
Specifications

WAPN008-1 User’s Manual Introduction
Overview
WAPN008-1 PCI module is designed to provide wireless communication for Moxa industrial wireless products.
It communicates via 2.4 GHz/4.9 GHz/5 GHz channels. The WAPN008-1 uses the AR9344 SoC Wireless chipset
from Atheros.
Specification
Features
WAPN008-1
Chipset
Atheros AR9344
security engine
- 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE
802.1X/RADIUS, TKIP and AES)
Connectors
Defined BTB connector is using 2x40 pins header, and Support PCI Express standard.
Power requirement
3.3V +/-10%
Dimension
60mm x 60mm x 1.2mm
Operating
Temperature
-40 to +80 ℃ (installed properly inside the enclosure of the final products)
Storage
Temperature:
-40 to +150℃ (installed properly inside the enclosure of the final products)
Operates in 2.4
and 5 GHz
frequency bands.
(frequency range)
US:
2,400 to 2,483.5 MHz
4,940 to 4,990 MHz
5,725 to 5,850 MHz
EU:
2,400 to 2,483.5 MHz
5,725 to 5,875 MHz

2
Chapter 2 Getting Started
This chapter covers the module layout, and block diagram, hardware installation of the WAPN008-1. Software
installation is covered in the next chapter.
The following topics are covered:
Module Layout
Block Diagram
Hardware Installation
Software Installation

WAPN008-1 User’s Manual Getting Started
Module Layout
Top and Bottom
Block Diagram
Below is a block diagram of the WAPN008-1.

WAPN008-1 User’s Manual Getting Started
Connector Locations

WAPN008-1 User’s Manual Getting Started
PCI Bus Connector PIN Assignments
Function
Connect to
Pin
Pin
Function
Connect to
3.3v
3.3v
1
2
GND
GND
3.3v
3.3v
3
4
GND
GND
3.3v
3.3v
5
6
ERXD3
PHY RGMII
3.3v
3.3v
7
8
ERXD2
PHY RGMII
3.3v
3.3v
9
10
ERXD1
PHY RGMII
3.3v
3.3v
11
12
ERXD0
PHY RGMII
3.3v
3.3v
13
14
GND
GND
GPIO 16
I2C_SCLK
15
16
GND
GND
GPIO 17
I2C_DATA
17
18
ETX_CLK
ETX_CLK
GND
GND
19
20
GND
GND
GPIO 21
POWER 2
21
22
GND
GND
GPIO 1
JP1 Debug
23
24
ETX_EN
ETX_EN
GND
GND
25
26
GND
GND
GPIO 4
S17_INT
27
28
GND
GND
GND
GND
29
30
ETXD3
PHY RGMII
GPIO 0
I2C_INT0
31
32
ETXD2
PHY RGMII
GND
GND
33
34
ETXD1
PHY RGMII
GPIO 3
UR_DSR
35
36
ETXD0
PHY RGMII
GPIO 9
UR_SIN
37
38
GND
GND
GPIO 10
UR_SOUT
39
40
GND
GND
GPIO 13
MDC
41
42
ERX_CLK
ERX_CLK
GPIO 14
MDIO
43
44
GND
GND
GPIO 20
POWER 1
45
46
GND
GND
GND
GND
47
48
ERX_EN
ERX_EN
GPIO 22
POWER 3
49
50
GND
GND
GND
GND
51
52
GND
GND
GPIO 2
UR_DTR
53
54
EMDC
GIGA PHY
GND
GND
55
56
EMDIO
GIGA PHY
GPIO 11
Reset
57
58
GND
GND
GND
GND
59
60
GND
GND
GPIO 12
LAN 10/100
61
62
TXP0
10/100 LAN
GND
GND
63
64
TXN0
10/100 LAN
GPIO 15
Reserved
65
66
GND
GND
GND
GND
67
68
RXP0
10/100 LAN
SYS_RST_L
GIGA PHY Reset
69
70
RXN0
10/100 LAN
AVDD18
Fast Ethernet bios
71
72
GND
GND
AVDD18
Fast Ethernet bios
73
74
GND
GND
AVDD18
Fast Ethernet bios
75
76
USB_DM
USB port
GND
GND
77
78
USB_DP
USB port
GND
GND
79
80
GND
GND

WAPN008-1 User’s Manual Getting Started
Hardware Installation
The WAPN008-1 can be installed into all Moxa wireless system board series.
Step for Installation
1. Install the WAPN008-1 PCI card on the system board. Apply pressure to both bus
connectors and gently press the board onto the stack. The board should slide into the matching
bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins.
2. Screw on the WAPN008-1 PCI card.
3. Screw on the all the necessary chassis.
Software Installation
After physically installing the WAPN008-1, your operating system must be configured to recognize
the new system board.
Step for Installation
1. Apply power to the system board.
2. Connect system board and PC with Ethernet cable.
3. Open a browser and type: 192.168.127.253 to open the system login webpage.
4. Login the webpage with default password: root in order to verify that all of the hardware is
install properly.

WAPN008-1 User’s Manual Getting Started
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, (example - use only shielded interface cables when connecting to computer or
peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the
antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This
transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that
20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area
with the following: "Contains FCC ID: SLE-WAPN008-1 ”

WAPN008-1 User’s Manual Getting Started
Information for the OEMs and Integrators
Any party of the installer who likes to use the module of 4.9GHz band shall fulfill licensing requirement (§90.1207).
The installation to Aeronautical mobile operations are prohibited (§90.1205).
The end product with an embedded WAPN008-1 module may also need to pass the FCC Part 15 unintentional
emission testing requirements and be properly authorized per FCC Part 15.
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
This radio transmitter FCCID: SLE-WAPN008-1 has been approved by FCC to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
Maximum Permissible Exposure (MPE): Ensure that at least 50 cm separation distance is maintained between
the wireless module and the body of the user, when Panel antennas, ANT-WSB5-PNF-18 or ANT-WDB-PNF-1518,
are used.
Antenna List
No.
Manufacturer
Part No.
Antenna Type
Peak Gain
1
MOXA
ANT-WDB-ANM-0306
Dipole
3.8dBi For 2.4 GHz
6.3dBi For 4.9 GHz
6.3dBi For 5 GHz
2
MOXA
ANT-WDB-ARM-0202
Dipole
1.8dBi For 2.4GHz
1.8dBi For 4.9 GHz
1.8dBi For 5 GHz
3
MOXA
ANT-WDB-ARM-02
Dipole
2.04dBi For 2.4GHz
0.81dBi For 4.9 GHz
0.81dBi For 5 GHz
4
MOXA
ANT-WDB-ANM-0502
Dipole
4.62dBi For 2.4GHz
2dBi For 4.9 GHz
2dBi For 5GHz
5
MOXA
ANT-WSB5-ANF-12
Dipole
12dBi For 5 GHz
6
MOXA
ANT-WSB5-PNF-18
Panel
18dBi For 5 GHz
7
MOXA
ANT-WDB-PNF-1518
Panel
15dBi For 2.4GHz
18dBi For 5GHz
8
Huber+Suhner
1356.17.0042
Railway
13dBi For 5GHz
9
Huber+Suhner
1356.17.0077
Dipole
14dBi For 5GHz

WAPN008-1 User’s Manual Getting Started