Moxa Technologies ioLogik R1210 Series: ioLogik R1212 Series: ioLogik R1214 Series: ioLogik R1240 Series: ioLogik R1241... User manual

P/N: 1802012002014
*1802012002014*
ioLogik R1200 Series
Quick Installation Guide
RS-485 Remote I/O
Version 4.1, January 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
•1 ioLogik R1200 series remote I/O product
•Quick installation guide (printed)
Specifications
Input Current ioLogik R1210 Series: 154 mA @ 24 VDC
ioLogik R1212 Series: 187 mA @ 24 VDC
ioLogik R1214 Series: 207 mA @ 24 VDC
ioLogik R1240 Series: 216 mA @ 24 VDC
ioLogik R1241 Series: 343 mA @ 24 VDC
Input Voltage
12 to 48 VDC
Operating Temperature
Standard Models: -10 to 75°C (14 to 167°F)
Wide Temp. Models: -40 to 85°C (-40 to
185°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Installation
Jumper Settings
The models with DIO or AI channels require configuring the jumpers
inside the enclosure. Remove the screw located on the back panel and
open the cover to configure the jumpers.
DIO mode configuration is shown
to the right (default: DO Mode).
Analog mode configuration is
shown to the right (default:
Voltage Mode).
I/O Wiring
Digital Input/Output (Sink Type)

- 3 -
Analog Input
Relay Output (Form A)
NOTE
A “load” in a circuit schematic is a component or portion of the
circuit that consumes electric power. For the diagrams shown in
this document, “load” refers to the devices or systems connected
to the remote I/O unit.
Mounting
The ioLogik R1200 is designed with a vertical form factor, and can be used
with both DIN-Rail and wall mounting applications. When mounting on a
rail, release the bottom mounting kit, install the ioLogik on the rail, and
then restore the bottom mounting kit to fix the ioLogik to the rail. When
using wall mounting, release both the upper and bottom DIN-Rail kits.
Power and Networking
Connect the +12 to +48 VDC
power line to the ioLogik R1200’s
terminal block
V+ terminal;
connect
the ground from the
power supply to the V
- terminal.
Connect the ground pin (
) if
earth ground is available.
NOTE
For safety reasons, the wires attached to the power should be at
least 2 mm (12 gauge) in diameter.
Switch Settings
The R1200 series provides Dual/Rep and Run/Initial switch settings to set
up the communication mode.
Duel (Default)
Dual RS-485 mode
Rep
Repeater mode
Run
User define communication parameters
Initial (Default)
Initial RS-485 communication parameters

- 4 -
LED Indicators
Type
LED Color
LED Action
PWR Green
On:
Power On
Off:
Power Off
RDY
Green/
Red
Green:
System Ready
Green
Blinking:
Located
Red:
System Boot-up Error
Red
Blinking:
Firmware upgrade / USB upgrade
Green/Red
Blinking:
Safe Mode
Off:
System NOT Ready
P1
Green/
Amber
Green:
Tx
Amber:
Rx
Blinking:
Data Transmitting
Off:
Disconnected
P2 Green/
Amber
Green:
Tx
Amber:
Rx
Blinking:
Data Transmitting
Off:
Disconnected
System Configuration
ioSearch Utility
ioSearch is a search utility that helps users locate an ioLogik R1200 on the
local network. The utility can be downloaded from Moxa’s website.
Load Factory Default Settings
There are three ways to restore the ioLogik R1200 to the factory default
settings.
1. Hold the RESET button for 5 seconds.
2. Right click the specified ioLogik in the ioSearch utility and select
“Reset to Default.”
3. Select “Load Factory Default” from the web console.
Modbus Address Table
Please refer to the user’s manual for details of the ioLogik’s Modbus
address.
How to Download the Software
Step 1: Click on the following link to open the Support & Downloads
search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1

- 5 -
Step 2: Type the model name in the search box or select a product from
the drop down box and then click Search.
Step 3: Click the Software Packages link to download the latest
software for the product.