Moxa Technologies ioLogik 2500 Series User manual

P/N: 1802025000034
*1802025000034*
ioLogik 2500 Series
Quick Installation Guide
Smart Remote I/O
Version 6.1, January 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
•ioLogik 2500 series device
•3-pin screw terminal block (for power input)
•2 12-pin screw terminal blocks (for I/O)
•2 8-pin RJ45-to-DB9 cables (CBL-RJ45M9-150)
•1 antenna (only for wireless modules)
•Quick installation guide (printed)
Appearance
Top View
Front View

- 3 -
Physical Dimensions (unit = mm/inch)
Specifications
Input Current
ioLogik 2512 Series:
ioLogik 2512-GPRS Series:
ioLogik 2512-HSPA Series:
ioLogik 2512-WL1 Series:
ioLogik 2542 Series:
ioLogik 2542-GPRS Series:
ioLogik 2542-HSPA Series:
ioLogik 2542-WL1 Series:
254 mA @ 24 VDC,
529 mA @ 12 VDC,
133 mA @ 48 VDC
416 mA @ 24 VDC
352 mA @ 24 VDC,
728 mA @ 12 VDC,
187 mA @ 48 VDC
354 mA @ 24 VDC,
735 mA @ 12 VDC,
189 mA @ 48 VDC
281 mA @ 24 VDC,
589 mA @ 12 VDC,
144 mA @ 48 VDC
494 mA @ 24 VDC
311 mA @ 24 VDC,
649 mA @ 12 VDC,
166 mA @ 48 VDC
380 mA @ 24 VDC,
797 mA @ 12 VDC,
203 mA @ 48 VDC
Input Voltage
12 to 48 VDC
Operating Temperature Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models:
Ethernet: -40 to 75°C (-40 to 167°F)
Wireless: -30 to 70°C (-22 to 158°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)

- 4 -
Hardware Installation
I/O Wiring
Digital Inputs/Outputs
Analog Inputs
Mounting
There are two sliders on the back of the unit for DIN rail and wall
mounting.
•Mounting on a DIN rail
Step 1: If the spring-loaded bracket is locked in place, push the
recessed button to release it.
Step 2: Insert the top of the rail into the upper lip of the attachment
plate’s slot.
Step 3: The attachment unit should now snap into place along the
rail.
•Mounting on a wall (optional)
Step 1: Remove the DIN rail attachment plate.
Step 2: Install the wall mounting kit to the back of the unit with M3
screws.
Step 3:
Install the unit to the wall. The heads of the
screws should be less than 6.0 mm in diameter, and
the shafts should be less than 3.5 mm in diameter, as
shown in the figure
at the right.

- 5 -
Connecting the Power
The ioLogik 2500 can receive power from a 12 to 48 VDC power source.
Input power is applied to the positive (V+) and negative (V-) terminals on
the connector.
For most applications, it is
desirable to ground the system by
connecting the system's power
supply function ground (FG) to the
power
terminal's ground and the
chassis ground (indicated with red
markings in the image at the
right).
NOTE
For safety reasons, wires connecting the power supply should be
at least 2 mm in diameter (e.g., 12 gauge wires).
Connecting to a Network
The ioLogik 2500 has four built-in RJ45 Ethernet ports for connecting
standard direct or crossover Ethernet cables.
LED Indicators
Type
Color
Description
Power
(PWR)
Green
System power is ON
Off
System power is OFF
Ready
(RDY)
Green
System ready
Red
System error
Off
System is not ready
Ethernet Port
(L1/L2/L3/L4)
Green
Ethernet connection enabled in 100 Mbps
Amber
Ethernet connection enabled in 10 Mbps
Flashing
Data transmitting
Off
Disconnected
Serial Port
(P1/P2)
Green
Tx
Amber
Rx
Flashing
Data transmitting
Off
Disconnected
SD Green SD card inserted
Flashing
SD card being accessed
I/O Channel
Status*
Green
Channel ON
Off
Channel OFF or No Counter/Pulse Signal
W.Link**
Green
Cellular connection established
Off
Off
Signal Status**
Off
No signal, or No SIM card
1 LED
Weak or insufficient (SMS only)
2 LEDs
Average (good for cellular connections)
3 LEDs
Excellent signal
*Use the rotary switch to select which module's I/O channel status is
displayed.
**Wireless Modules Only.

- 6 -
System Configuration
Configuration via IOxpress Utility
The configuration of the ioLogik 2500 is mainly done with the IOxpress
utility. IOxpress is a search utility that helps users locate an ioLogik 2500
device on the local network. The latest version of the utility can be
downloaded from Moxa's website.
•Default IP Address: 192.168.127.253
•Default Subnet Mask: 255.255.0.0
NOTE
Be sure to configure the host PC’s IP address to the same subnet
as the ioLogik 2500. For example, 192.168.127.250
Load Factory Default Settings
There are three ways to restore the ioLogik 2500 to factory default
settings.
1. Hold the RESET button for 5 seconds.
2. In the IOxpress utility, right-click on the ioLogik device to be reset
and select Reset to Default.
3. Select Load Factory Default from the web console.
WARNING
This equipment is intended to be used in Restricted Access
Locations. External metal parts are hot! Before touching it,
special attention or protection is necessary.
How to Download the Software
Step 1: Click on the following link to open the Support & Downloads
search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1
Step 2: Type the model name in the search box or select a product from
the drop down box and then click Search.

- 7 -
Step 3: Click the Software Packages link to download the latest
software for the product.
ATEX Information
1. Certificate number: DEMKO 15 ATEX 1603X
2. Certification string: Ex nA IIC T4 Gc
3. Standards covered:
EN 60079-0:2012+A11:2013, EN 60079-15:2010
4. The equipment shall be installed in an enclosure that provides a
degree of protection not less than IP54 in accordance with EN
60079-15 and accessible only by the use of a tool.
5. These products are for use in an area of not more than pollution
degree 2 in accordance with EN 60664-1.