Moxa Technologies TC-6110 Series User manual

P/N: 1802061100014
*1802061100014*
TC-6110 Series Train Computer
Quick Installation Guide
Edition 5.0, March 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Overview
TC-6110 train computers are specifically designed for onboard train
applications. They come with 2 Gigabit LAN ports, 1 RS-232 serial port, 3
USB 2.0 hosts, and 2 expansion slots, offering an ideal solution for any
auxiliary train application.
To guarantee high reliability and availability during train operations,
TC-6110 computers come with M12 connectors for Gigabit LAN ports,
USB ports, and dual power inputs. In addition, the expansion modules
offer high flexibility for system integration. Users can easily expand the
system with additional storage modules for greater storage capacity.
Model Names and Package Checklist
The TC-6110 Series includes the following models:
•TC-6110-W7E: Modular 3U/42HP train computer, Intel Atom D525
1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power, WLAN
module (available on request), Win7 Embedded (32-bit) , -25 to 55°C
operating temperature range, compliant with EN 50155 Class T1
•TC-6110-T-W7E: Modular 3U/42HP train computer, Intel Atom
D525 1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power,
WLAN module (available on request), Win7 Embedded (32-bit), -40
to 70°C operating temperature range, compliant with EN 50155 Class
TX
•TC-6110-CT-W7E: Modular 3U/42HP train computer, Intel Atom
D525 1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power,
conformal coating, WLAN module (available on request), Win7
Embedded (32-bit) , -25 to 55°C operating temperature range,
compliant with EN 50155 Class T1
•TC-6110-CT-T-W7E: Modular 3U/42HP train computer, Intel Atom
D525 1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power,
conformal coating, WLAN module (available on request), Win7
Embedded (32-bit), -40 to 70°C operating temperature range,
compliant with EN 50155 Class TX
•TC-6110-LX: Modular 3U/42HP train computer, Intel Atom D525 1.8
GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power, WLAN
module (available on request), Linux Debian 7, -25 to 55°C operating
temperature range, compliant with EN 50155 Class T1
•TC-6110-T-LX: Modular 3U/42HP train computer, Intel Atom D525
1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power, WLAN
module (available on request), Linux Debian 7, -40 to 70°C operating
temperature range, compliant with EN 50155 Class TX
•TC-6110-CT-LX: Modular 3U/42HP train computer, Intel Atom D525
1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power,
conformal coating, WLAN module (available on request), Linux
Debian 7, -25 to 55°C operating temperature range, compliant with
EN 50155 Class T1
•TC-6110-CT-T-LX: Modular 3U/42HP train computer, Intel Atom
D525 1.8 GHz CPU, 4 expansion slots, 24 to 110 VDC isolated power,
conformal coating, WLAN module (available on request), Linux
Debian 7, -40 to 70°C operating temperature range, compliant with
EN 50155 Class TX

- 3 -
Each basic system model is shipped with following standard items:
•TC-6110 train computer
•Rackmount kit
•Power switch with cable extender
•Power cable
•Documentation CD or DVD
•Quick installation guide (printed)
•Warranty card
Hardware Installation
Front View
Front Panel LEDs
Information about each LED is given in the following table.
LED Name
LED Color
LED Function
Power
Green
Power is on and functioning normally
Off
Power is off or power system error
System
Ready
Yellow
Logged in to OS, functioning normally
Off
Login failure or OS not functioning normally
Tx (P1)
Green
Serial port P1 transmitting data
Off
Serial port P1 not transmitting data
Rx (P1)
Yellow
Serial port P1receving data
Off
Serial port P1 not receiving data
X1-X4
Green
Programmable by users
Off
Programmable by users
LAN (P1-P2)
Green
Working 100 Mbps Ethernet link
Yellow
Working 1000 Mbps Ethernet link
Off
Disconnected or short circuit
Connecting to a Display
The TC-6110 comes with a female D-Sub DE-15 VGA interface on the
front panel. To ensure that the monitor image remains stable, be sure to
tighten the connector’s thumbscrews after connecting the cable.
Reset Button
The reset button on the TC-6110’s front panel initiates a soft system
reboot. Once the system has completed the reboot the System Ready
LED will maintain a steady glow.

- 4 -
Powering the TC-6110
TC-6110 computers come with DC power inputs. When connecting the
TC-6110 to an office AC source (for testing), an adaptor must be used. To
connect the AC adaptor, follow these steps:
Step 1: Connect the ends of the extended power switch cable to the male
portion of the 2-pin Euroblock (provided in the package).
Step 2: Plug the male Euroblock into the matching female terminal on the
front panel.
Step 3: Make sure the power switch is turned off (the Open position as
indicated in the diagram below).
Step 4: Connect the earth/ground cable to the
Phillips
-head ground connector on the lower right
corner of the
front panel.
Step 5: Connect the power cable (CBL-Power Jack to M12) to the M12
(A-coded, 5-pin, male) connector as shown at right. Then connect the
power connector to power input 1 on the front panel.
Step 6: On the other side of the power cable, connect to the
PWR-24250-DT-S1 power adaptor (optional), and a PWC-series power
cord (optional).
Step 7: To check power redundancy, use the same method to connect
the power to the power input 2.
Step 8: Switch on the TC-6110 (Short state). If power supply is
connected properly, both power input and system power LEDs will be on
(green), as well as the yellow Ready LED.

- 5 -
When installing TC-6110 computers at a field site, follow these steps:
Step 1: Connect the ends of the extended power switch cable to the male
portion of the 2-pin Euroblock (provided); you may also choose to not use
the cable extender, and connect the switch to the terminal directly.
Step 2: Plug the male Euroblock into the matching female terminal on the
front panel.
Step 3: Make sure the power switch is turned off (the Open position as
indicated in the diagram below).
Step 4: Connect the earth/ground cable to the
Phillips
-head ground connector on the
lower right corner
of the
front panel.
Step 5: Connect the M12 connector to the power source using the pin
assignment at right.
Step 6: Connect this M12 connector to power input 1 on the front panel of
the computer.
Step 7: Use the same method to provide power to power input 2.
Step 8: Turn on the computer. If the power supply is connected properly,
the Power and System Power LEDs will be on, and the yellow Ready
LED will also be on. If you need to disconnect the power, reverse these
steps.
Please note that the branch circuit over current protection must be rated
maximum 10 A.

- 6 -
USB Ports
The TC-6110 embedded computer
has three USB 2.0 ports: two
come with type A connectors
and one with
an M12 (D-coded,
5
-pin, female) connector. All of
the ports are UHCI, Rev 2.0
compliant and support Plug & Play
Pin
USB
1
D+
2
D-
3
+5V
4
GND
5
N.C.
and hot swapping. These ports can be used to connect USB devices, such
as a keyboard, mouse, USB flash disk, and USB CD
-ROM. In addition,
both USB ports support system boot up, which can be activated by
modifying the BIOS settings.
See the following table and figure for the
pin
assignment of the USB host with M12 connector.
Serial Ports
The TC-6110 comes with one DB-9 (male) RS-232 serial interface. The
pin assignments for the ports are shown in the following table:
Pin
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
Ethernet Ports
The TC-6110 has two 10/100/1000 Mbps LAN ports with M12 (A-coded,
8-pin, female) hardware interfaces. When the cable is properly connected,
the LEDs on the front panel will glow to indicate a successful link.
Pin
10/100 Mbps
1000 Mbps
1
–
DC+
2
–
DD+
3
–
DD-
4
TX-
DA-
5
RX+
DB+
6
TX+
DA+
7
–
DC-
8
RX-
DB-
These LAN ports use DHCP for the IP address.

- 7 -
Audio Input/Output
The TC-6110 Series comes with an audio input/output connector and an
M12 (A-coded, 8-pin, female) connector. Use a cable to connect the audio
input and output. See the following figure and table for pin assignments.
Pin
Audio
1
Line in, right
2
GND
3
–
4
Line in, left
5
Line out, left
6
–
7
Line out, right
8
GND
Installing the SSD/HDD into the Storage Tray
The TC-6110 computers come with two storage trays that can be installed
with SSD or HDD for storage expansion. Refer to the hardware manual for
detailed description for the installation steps.
Configuring the Ethernet Interface
Follow these steps to configure the Ethernet interface for a static network
address:
Step 1:
Go to Start Control Panel Network and Internet 
Network Connections.
Step 2:
Go to the Local Area Connection tab and click Properties,
then
click Internet Protocol (TCP/IP), and lastly select
Properties.
Step 3:
Click OK after inputting the proper IP address and netmask.
Refer to User’s Manual for additional configuration information.