Moxa Technologies NPort 5210 User manual

LED Indicators—The top panels of NPort 5200 have four LED
indicators, as described in the following table.
5200 Series
Quick Installation Guide
Second Edition, December 2003
LED
Name
LED
Color LED Function
red
Steady on: Power is on and NPort 5200 is
booting up.
Blinking: Indicates an IP conflict, or DHCP or
BOOTP server did not respond
properly.
green
Steady on: Power is on and NPort 5200 is
functioning normally.
Blinking: The device server has been located
by Administrator’s Location
function
Ready
off Power is off, or power error condition exists.
orange 10 Mbps Ethernet connection.
green 100 Mbps Ethernet connection.
Ethernet
off Ethernet cable is disconnected, or has a short.
orange Serial port is receiving data.
green Serial port is transmitting data.
P1, P2
off No data is being transmitted or received through
the serial port.
1. Overview
Welcome to the NPort 5200 Series, a compact palm-sized data
communication device that allows you to control RS-232 (NPort
5210/5230) or RS-422/485 (NPort 5230/5232/5232I) serial devices over a
TCP/IP-based Ethernet.
2. Package Checklist
Before installing the NPort 5200 Series products, verify that the package
contains the following items:
 1 NPort 5200 2-port Serial Device Server
 Documentation & Software CD
 NPort 5200 Series Quick Installation Guide
Optional Accessories
 DK-35A DIN-Rail Mounting Kit (35 mm)
 CBL-RJ45M9-150
 CBL-RJ45F9-150
 CBL-RJ45M25-150
 CBL-RJ45F25-150
RJ45 (8-pin) to DB9 (M) cable, 150 cm
RJ45 (8-pin) to DB9 (F) cable, 150 cm
RJ45 (8-pin) to DB25 (M) cable, 150 cm
RJ45 (8-pin) to DB25 (F) cable, 150 cm
DIN-Rail Power Supply and Adapter
4. Hardware Installation Procedure
STEP 1: After removing NPort 5200 from the box, the first thing you
should do is connect the power adaptor. Connect the 12-30 VDC power
line with NPort 5200’s terminal block, or connect the DIN-Rail power
supply with NPort 5200’s terminal block.
STEP 2: Connect NPort 5200 to a network. Use a standard
straight-through Ethernet cable to connect to a Hub or Switch. When
setting up or testing NPort 5200, you might find it convenient to connect
directly to your computer’s Ethernet port. In this case, use a cross-over
Ethernet cable.
Notify your sales representative if any of the above items is missing or
damaged.
3. Hardware Introduction
As shown in the following figures, NPort 5210 has two 8-pin RJ45 ports,
both for the RS-232 interface, NPort 5230 has one 10-terminal terminal
block, with 5 pins used for one RS-232 port, and 5 pins used for one
RS-422/485 port, and NPort 5232 /5232I has one 10-terminal terminal
block, with all pins used for RS-422/485 ports.
STEP 3: Connect NPort 5200’s serial port to a serial device.
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button.
—1——2——3—

NPort 5210/5230: 12 to 30 VDC, 305
mA at 12V (max.)
NPort 5232: 12 to 30 VDC, 275
mA at 12V (max.)
Power requirements
NPort 5232I: 12 to 30 VDC, 365
mA at 12 V (max.)
Operating temp. 0 to 55◦C (32 to 131◦F)
Operating humidity 5 to 95% RH
NPort 5210/5230/
5232
(including ears)
90 × 100.4 × 22 mm
3.54 × 3.95 × 0.87 in
Dimensions
(W×D×H)
NPort 5210/5230/
5232
(without ears)
67 × 100.4 × 22 mm
2.64 × 3.95 × 0.87 in
NPort 5232I 90 × 100.4 × 35 mm
(including ears) 3.54 × 3.95 ×1.37 in
NPort 5232I 67 × 100.4 × 35 mm
(without ears) 2.64 × 3.95 × 1.37 in
Surge protection 15 KV ESD for serial port
Magnetic isolation 1.5 KV for Ethernet
4 KV Burst (EFT), EN61000-4-4
Power line
protection 2 KV Surge, EN61000-4-5
Regulatory
approvals
FCC Class A, CE Class A, UL, CUL, TÜV
Note: NPort 5232/5232I has 2 RS-422/485 ports. The pin assignments
are the same as NPort 5230’s port 2. Refer to the “NPort 5200
Series User’s Manual” for more details.
7. Pin Assignments and Cable Wiring—NPort 5230
—6—
Terminal Block Wiring
8. Environmental Specifications
STEP 4: Placement Options
In addition to placing
NPort 5200 on a
desktop or other
horizontal surface, you
may also make use of
the DIN-Rail or Wall
Mount options, as
illustrated here.
Wall Mount
DIN-Rail
5. Software Installation Information
To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort
Installation CD window opens, click on the Installation button, and then
follow the instructions on the screen.
To view detailed information about NPort 5200 Administration Suite,
click on the Documents button, and then select “NPort 5200 Series
User’s Guide” to open the pdf version of this user’s guide.
The PComm Lite program is also included in the Documentation &
Software CD free of charge. Install PComm Lite to use the Serial
Console to configure the initial IP address.
6. Pin Assignments and Cable Wiring—NPort 5210
RJ45 (8-pin) Connector Pinouts
Cable Wiring (RS-232)
Four cables are provided as optional accessories that can be used to
connect NPort 5210 to RS-232 serial devices. For your convenience, we
show precise cable wiring diagrams for each of the four cables.
P/N:18020520001
RJ45 (8-pin) to DB25 Female (Cable Name: CBL-RJ45F25-150)
RJ45 (8-pin) to DB25 Male (Cable Name: CBL-RJ45M25-150)
RJ45 (8-pin) to DB9 Male (Cable Name: CBL-RJ45M9-150)
RJ45 (8-pin) to DB9 Female (Cable Name: CBL-RJ45F9-150)
—5— —4—