MS Schippers MS Pigsleeper Flexy User manual

Assembly instructions MS Pigsleeper
Flexy

2
Introduction
This document describes how to correctly assemble the Pigsleeper Flexy. Everything
is explained with pictures.

3
Content
Introduction............................................................................................................................................. 2
Mounting the crossbar............................................................................................................................ 4
Mounting the upper section.................................................................................................................. 10
Mounting the Cup holder and bucket holder (OPTIONAL) ................................................................... 12
Mounting the cup holder on top........................................................................................................... 15
Installing the anaesthesia unit .............................................................................................................. 16
Isoflurane filter holder .......................................................................................................................... 17
Installing the compressor...................................................................................................................... 18
USB flash drive....................................................................................................................................... 19
Purple bottle top ................................................................................................................................... 19
Required tools
Ring/socket wrench 10 + 13
Allen key for M5, M6 and M8

4
Mounting the crossbar
1. Take the crossbar (traverse) and remove the foil.
2. The crossbar is delivered with all necessary nuts and bolts.
Now remove the side plate, which is attached with nuts and bolts (see drawing
and picture).
You will need a size 13 wrench and a M8 Allen key.

5
3. Loosen the two Allen screws on the other side of the crossbar slightly so that
they are flush with the plate.
4. Now remove the support mounted on top of the crossbar. This can be done
manually, as it is equipped with a rotary knob.

6
5. Place the crossbar on the middle beam of the trolley frame.
6. Then slide the side plate that you removed in step 2 back onto the frame.
Push it between the bar of the frame and the side of the crossbar.
Tip: First place the lock nut on the inside of the metal plate. Then screw the
M8 bolt in from the outside and fasten it.
7. Now that the crossbar is in place, it can be tightened on both sides at the
bottom with all 4 Allen screws.
Tighten the screws until the crossbar is firmly clamped to the frame.
See image at point 8 for a complete set-up.

7
8. Now take the 2 green boxes and the 2 toolboxes. Place them into the frame as
shown below.
9. Now insert the support back into the holder and tighten it to the desired
working height. The rotary knob is located on the rear.

8
Mounting the cable drum
10.The cable drum is mounted with the provided holder as follows.
Take the bracket and remove the bolts and nuts with a size 10 wrench and a
M5 Allen key.
.
11.The support can be mounted in 2 ways. Mount it according to the working
height. The 2 ways are shown below.
Caution! Do not tighten the screws yet. On the next page you’ll see the
complete set-up.
Option 1: High Option 2: Low

9
12.Make sure that the screw heads protrude, not the nuts. Then hook the black
bracket of the cable drum onto the two support bolts.
13.Then tighten the support bolts and nuts so that the cable drum is firmly
attached. The assembled frame now looks like this:
a. There are 2 variants of the power strip. The image shows a black one,
but it may also be that a red variant is supplied. Quality remains the
same

10
Mounting the upper section
14.Now remove the 4 bolts and the 2 black buttons from the crossbar. You will
need a M8 Allen key.
15.Then place the upper part on the crossbar as follows.

11
16.Screw the bolts and star-shaped rotary knobs back into the crossbar so that
the upper section is firmly attached. You will need a M8 Allen key.
17. The Pigsleeper now looks like this:

12
Mounting the Cup holder and bucket holder (OPTIONAL)
18.If you have the optional cup holder for the side, then this must be mounted
first. Take the cup holder and remove the bolts. You will need the size 10
wrench and a M5 Allen key.
19.Place the holder in the location with predrilled holes. This can be on the left or
right side, depending on your own wishes.

13
20.Take the bucket holder and unscrew 1 nut.
21.Fasten the support in the hole of the holder. Then place the bucket in the
bucket holder.

14
22.The PigSleeper now looks like this.

15
Mounting the cup holder on top
Green cups: Item No. 8802770
Take the cup holder. Remove the two M6 bolts in the upper part.
23.Fasten the support to the upper part with the holes provided. Then tighten it
with a M6 Allen key.
24.The Pigsleeper now looks like this:

16
Installing the anaesthesia unit
1. Take the anaesthesia unit and hang it on the free, short side of the trolley.
2. Take the two plugs (Blue: Electric/Sensors, Black: Air) of the piglet bowls
(“upper part”) and plug them into the anaesthesia unit. (See picture.) Lock
them by tightening it.

17
3. Attach one side of the blue “vacuum” hose to the piglet bowl unit. Attach the
other side to the supplied Y-Piece. Also montage the other two blue “vacuum”
hoses on to the Y-Piece.
Isoflurane filter holder
1. Take 2 isoflurane filters and place them in the intended holder.
2. Attach the holder on top of the anaesthesia unit. (See picture.)
3. Now attach the two outlets of the blue hose to the two filters.

18
Installing the compressor
1. Take the thin blue hose and 2 couplings (1 in bags in the compressor box
and 1 in bags with the USB stick and purple hose).
2. Attach both couplings to the hose. (See picture.)
3. Place the compressor on the
lower shelf of the cart.
4. You can now attach the hose with
both couplings to the compressor
and the trolley (See picture).
Connection, side of
the compressor
Connection, side of
the anesthesia unit

19
5. Put the plug of the compressor in the cable reel. And put the cable reel
power plug in the socket. (230V)
6. Switch on the compressor and check that it is set to 4 bar. A lower
pressure to a minimum of 1.7 bar is possible. This results in a lower
consumption of anesthetic gas, but possibly also a less deep anesthetic. At
1.7 bar the consumption is the minimum as determined during DLG
certification.
USB flash drive
1. The USB flash drive can be used to download the log as Excel file. More
information can be found in the general manual of the PigSleeper.
Purple bottle top
1. This is used to fill the evaporator with isoflurane. (See Pigsleeper
operating instructions.)

20