Multitech Mtc-leu4 User manual

MultiConnect®Cell 100 Series Cellular Modem

(MTC-LEU4)

MTC-LEU4 Quick Start

MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) MultiTech Systems MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) MultiTech Systems MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) MultiTech Systems

Quick Start Quick Start Quick Start

Installing a SIM Card

If you want to operate the modem on a particular cellular network, install a

mini-SIM card [or mini SIM (2FF) form factor].

To install the mini-SIM card:

1. Locate the mini-SIM card slot on the side of the cellular

modem. The slot is labeled SIM.

2. Push the mini-SIM card into the slot until it snaps into place.

Installing the Cellular Modem

1. Connect the suitable antennas to the antenna connectors

(CELL and AUX).

2. To connect to the serial interface on the cellular modem

(serial version only):

■Connect the DE-9 connector (9-pin) of an RS-

232 cable to the RS-232 connector on the

cellular modem.

■Connect the other end to the serial port on your

computer or other desired device.

■Screw on the power lead from the power supply

module into the power connection on the cellular

modem.

■Plug the power supply into your power source.

3. To connect to the USB interface on the cellular modem

(USB version only):

■Connect the mini-USB connector end of the

cable to the USB connector on the cellular

modem.

■Connect the other end of the USB cable to your

computer, either directly or through a hub.

4. After power is applied:

■The POWER LED lights after the device powers

up.

■When the LS LED begins to blink, the device is

registered.

Mounting Device

1. Locate the groove on the bottom of the cellular modem.

2. Slide the mounting rod through the groove.

3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.

Refer to the user guide for an illustration of the mounting

rod, as well as the dimensions for placement of the screws.

MultiConnect®Cell 100 Series Cellular Modem (MTC-

LEU4)

Document Part Number: 82103650L

This publication may not be reproduced, in whole or in part, without the

specific and express prior written permission signed by an executive

by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,

whether express, implied or by estoppels, with respect to the content,

information, material and recommendations herein and specifically

disclaims any implied warranties of merchantability, fitness for any

particular purpose and non-infringement. Multi-Tech Systems, Inc.

reserves the right to revise this publication without obligation to notify any

person or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registered

trademarks of Multi-Tech Systems, Inc. All other brand and product

names are trademarks or registered trademarks of their respective

companies.

Quick Start Quick Start Quick Start Quick Start

Overview

The MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) provides

secure data communication between many types of devices that use

legacy and the latest communication technologies.

Note: Check for an updated version of this document at

http://www.multitech.com/brands/multiconnect-cell-100-series

Package Contents

Your MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4)

typically includes the following (varies with model):

Power

Supply

1 - 9 VDC power supply with removable blades, 1 -

NAM blade/plug, 1 - EURO blade/plug, 1 - UK

blade/plug, 1-AU/NZ blade/plug (serial units)

Cables 1 - Power cable from power supply (serial units) or

USB cable (USB units)

Antennas 2 - LTE external antennas, CELL and AUX

Documents 1 - Quick Start Guide, 1 - Warranty Plans, 1 -

Activation, Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons or

mounting feet

Device 1- MultiConnect®Cell 100 Series Cellular Modem

(LTE Cat 4)

Additional Information

For more information on your device, refer to the appropriate user guide:

http://www.multitech.com/brands/multiconnect-cell-100-series

LED Descriptions

The top panel contains the following LEDs:

■Power and Terminal Ready LEDs - The Power LED indicates

that DC power is present. The TR LED (serial model only)

when lit indicates that unit is ready to receive data.

■Modem LEDs - Two modem LEDs indicate carrier detection

(CD LED for serial models only) and link status (LS LED).

■Programmable Signal LEDs - Three signal LEDs can be

programmed to display the signal strength level of the wireless

connection.

Side Panel Connectors

Serial Models

USB Models

The device has connectors on both sides of the enclosure.

The right side includes:

■AUX Cellular auxiliary female SMA connector (for diversity)

■CELL cellular female SMA connector

■SIM card slot

■Power-saving switch (serial models only)

The left side includes:

■7-32 VDC power connector

■RS-232 (DE 9-pin, female-D) connector (serial models only)

■USB connector (USB models only)

Dimensions

The MTC is 4.169 inches x 3.00 inches x 1.163 inches

Regulatory Information

For additional regulatory information, see your device’s user guide or go

to your device’s page on www.multitech.com

RED Compliance (EU)

MultiTech declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU. The

declaration of conformity may be requested at

https://support.multitech.com.

Warning: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

Quick Start Quick Start Quick Start Quick Start

Overview

The MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) provides

secure data communication between many types of devices that use

legacy and the latest communication technologies.

Note: Check for an updated version of this document at

http://www.multitech.com/brands/multiconnect-cell-100-series

Package Contents

Your MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4)

typically includes the following (varies with model):

Power

Supply

1 - 9 VDC power supply with removable blades, 1 -

NAM blade/plug, 1 - EURO blade/plug, 1 - UK

blade/plug, 1-AU/NZ blade/plug (serial units)

Cables 1 - Power cable from power supply (serial units) or

USB cable (USB units)

Antennas 2 - LTE external antennas, CELL and AUX

Documents 1 - Quick Start Guide, 1 - Warranty Plans, 1 -

Activation, Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons or

mounting feet

Device 1- MultiConnect®Cell 100 Series Cellular Modem

(LTE Cat 4)

Additional Information

For more information on your device, refer to the appropriate user guide:

http://www.multitech.com/brands/multiconnect-cell-100-series

LED Descriptions

The top panel contains the following LEDs:

■Power and Terminal Ready LEDs - The Power LED indicates

that DC power is present. The TR LED (serial model only)

when lit indicates that unit is ready to receive data.

■Modem LEDs - Two modem LEDs indicate carrier detection

(CD LED for serial models only) and link status (LS LED).

■Programmable Signal LEDs - Three signal LEDs can be

programmed to display the signal strength level of the wireless

connection.

Side Panel Connectors

Serial Models

USB Models

The device has connectors on both sides of the enclosure.

The right side includes:

■AUX Cellular auxiliary female SMA connector (for diversity)

■CELL cellular female SMA connector

■SIM card slot

■Power-saving switch (serial models only)

The left side includes:

■7-32 VDC power connector

■RS-232 (DE 9-pin, female-D) connector (serial models only)

■USB connector (USB models only)

Dimensions

The MTC is 4.169 inches x 3.00 inches x 1.163 inches

Regulatory Information

For additional regulatory information, see your device’s user guide or go

to your device’s page on www.multitech.com

RED Compliance (EU)

MultiTech declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU. The

declaration of conformity may be requested at

https://support.multitech.com.

Warning: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

Quick Start Quick Start Quick Start Quick Start

Overview

The MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) provides

secure data communication between many types of devices that use

legacy and the latest communication technologies.

Note: Check for an updated version of this document at

http://www.multitech.com/brands/multiconnect-cell-100-series

Package Contents

Your MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4)

typically includes the following (varies with model):

Power

Supply

1 - 9 VDC power supply with removable blades, 1 -

NAM blade/plug, 1 - EURO blade/plug, 1 - UK

blade/plug, 1-AU/NZ blade/plug (serial units)

Cables 1 - Power cable from power supply (serial units) or

USB cable (USB units)

Antennas 2 - LTE external antennas, CELL and AUX

Documents 1 - Quick Start Guide, 1 - Warranty Plans, 1 -

Activation, Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons or

mounting feet

Device 1- MultiConnect®Cell 100 Series Cellular Modem

(LTE Cat 4)

Additional Information

For more information on your device, refer to the appropriate user guide:

http://www.multitech.com/brands/multiconnect-cell-100-series

LED Descriptions

The top panel contains the following LEDs:

■Power and Terminal Ready LEDs - The Power LED indicates

that DC power is present. The TR LED (serial model only)

when lit indicates that unit is ready to receive data.

■Modem LEDs - Two modem LEDs indicate carrier detection

(CD LED for serial models only) and link status (LS LED).

■Programmable Signal LEDs - Three signal LEDs can be

programmed to display the signal strength level of the wireless

connection.

Side Panel Connectors

Serial Models

USB Models

The device has connectors on both sides of the enclosure.

The right side includes:

■AUX Cellular auxiliary female SMA connector (for diversity)

■CELL cellular female SMA connector

■SIM card slot

■Power-saving switch (serial models only)

The left side includes:

■7-32 VDC power connector

■RS-232 (DE 9-pin, female-D) connector (serial models only)

■USB connector (USB models only)

Dimensions

The MTC is 4.169 inches x 3.00 inches x 1.163 inches

Regulatory Information

For additional regulatory information, see your device’s user guide or go

to your device’s page on www.multitech.com

RED Compliance (EU)

MultiTech declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU. The

declaration of conformity may be requested at

https://support.multitech.com.

Warning: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

Quick Start Quick Start Quick Start Quick Start

Overview

The MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4) provides

secure data communication between many types of devices that use

legacy and the latest communication technologies.

Note: Check for an updated version of this document at

http://www.multitech.com/brands/multiconnect-cell-100-series

Package Contents

Your MultiConnect®Cell 100 Series Cellular Modem (MTC-LEU4)

typically includes the following (varies with model):

Power

Supply

1 - 9 VDC power supply with removable blades, 1 -

NAM blade/plug, 1 - EURO blade/plug, 1 - UK

blade/plug, 1-AU/NZ blade/plug (serial units)

Cables 1 - Power cable from power supply (serial units) or

USB cable (USB units)

Antennas 2 - LTE external antennas, CELL and AUX

Documents 1 - Quick Start Guide, 1 - Warranty Plans, 1 -

Activation, Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons or

mounting feet

Device 1- MultiConnect®Cell 100 Series Cellular Modem

(LTE Cat 4)

Additional Information

For more information on your device, refer to the appropriate user guide:

http://www.multitech.com/brands/multiconnect-cell-100-series

LED Descriptions

The top panel contains the following LEDs:

■Power and Terminal Ready LEDs - The Power LED indicates

that DC power is present. The TR LED (serial model only)

when lit indicates that unit is ready to receive data.

■Modem LEDs - Two modem LEDs indicate carrier detection

(CD LED for serial models only) and link status (LS LED).

■Programmable Signal LEDs - Three signal LEDs can be

programmed to display the signal strength level of the wireless

connection.

Side Panel Connectors

Serial Models

USB Models

The device has connectors on both sides of the enclosure.

The right side includes:

■AUX Cellular auxiliary female SMA connector (for diversity)

■CELL cellular female SMA connector

■SIM card slot

■Power-saving switch (serial models only)

The left side includes:

■7-32 VDC power connector

■RS-232 (DE 9-pin, female-D) connector (serial models only)

■USB connector (USB models only)

Dimensions

The MTC is 4.169 inches x 3.00 inches x 1.163 inches

Regulatory Information

For additional regulatory information, see your device’s user guide or go

to your device’s page on www.multitech.com

RED Compliance (EU)

MultiTech declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU. The

declaration of conformity may be requested at

https://support.multitech.com.

Warning: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

MultiConnect®Cell 100 Series Cellular Modem

(MTC-LEU4)

MTC-LEU4 Quick Start

Quick Start Quick Start Quick Start

Installing a SIM Card

If you want to operate the modem on a particular cellular network, install a

mini-SIM card [or mini SIM (2FF) form factor].

To install the mini-SIM card:

1. Locate the mini-SIM card slot on the side of the cellular

modem. The slot is labeled SIM.

2. Push the mini-SIM card into the slot until it snaps into place.

Installing the Cellular Modem

1. Connect the suitable antennas to the antenna connectors

(CELL and AUX).

2. To connect to the serial interface on the cellular modem

(serial version only):

■Connect the DE-9 connector (9-pin) of an RS-

232 cable to the RS-232 connector on the

cellular modem.

■Connect the other end to the serial port on your

computer or other desired device.

■Screw on the power lead from the power supply

module into the power connection on the cellular

modem.

■Plug the power supply into your power source.

3. To connect to the USB interface on the cellular modem

(USB version only):

■Connect the mini-USB connector end of the

cable to the USB connector on the cellular

modem.

■Connect the other end of the USB cable to your

computer, either directly or through a hub.

4. After power is applied:

■The POWER LED lights after the device powers

up.

■When the LS LED begins to blink, the device is

registered.

Mounting Device

1. Locate the groove on the bottom of the cellular modem.

2. Slide the mounting rod through the groove.

3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.

Refer to the user guide for an illustration of the mounting

rod, as well as the dimensions for placement of the screws.

MultiConnect®Cell 100 Series Cellular Modem (MTC-

LEU4)

Document Part Number: 82103650L

This publication may not be reproduced, in whole or in part, without the

specific and express prior written permission signed by an executive

by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,

whether express, implied or by estoppels, with respect to the content,

information, material and recommendations herein and specifically

disclaims any implied warranties of merchantability, fitness for any

particular purpose and non-infringement. Multi-Tech Systems, Inc.

reserves the right to revise this publication without obligation to notify any

person or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registered

trademarks of Multi-Tech Systems, Inc. All other brand and product

names are trademarks or registered trademarks of their respective

companies.

MultiConnect®Cell 100 Series Cellular Modem

(MTC-LEU4)

MTC-LEU4 Quick Start

Quick Start Quick Start Quick Start

Installing a SIM Card

If you want to operate the modem on a particular cellular network, install a

mini-SIM card [or mini SIM (2FF) form factor].

To install the mini-SIM card:

1. Locate the mini-SIM card slot on the side of the cellular

modem. The slot is labeled SIM.

2. Push the mini-SIM card into the slot until it snaps into place.

Installing the Cellular Modem

1. Connect the suitable antennas to the antenna connectors

(CELL and AUX).

2. To connect to the serial interface on the cellular modem

(serial version only):

■Connect the DE-9 connector (9-pin) of an RS-

232 cable to the RS-232 connector on the

cellular modem.

■Connect the other end to the serial port on your

computer or other desired device.

■Screw on the power lead from the power supply

module into the power connection on the cellular

modem.

■Plug the power supply into your power source.

3. To connect to the USB interface on the cellular modem

(USB version only):

■Connect the mini-USB connector end of the

cable to the USB connector on the cellular

modem.

■Connect the other end of the USB cable to your

computer, either directly or through a hub.

4. After power is applied:

■The POWER LED lights after the device powers

up.

■When the LS LED begins to blink, the device is

registered.

Mounting Device

1. Locate the groove on the bottom of the cellular modem.

2. Slide the mounting rod through the groove.

3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.

Refer to the user guide for an illustration of the mounting

rod, as well as the dimensions for placement of the screws.

MultiConnect®Cell 100 Series Cellular Modem (MTC-

LEU4)

Document Part Number: 82103650L

This publication may not be reproduced, in whole or in part, without the

specific and express prior written permission signed by an executive

by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,

whether express, implied or by estoppels, with respect to the content,

information, material and recommendations herein and specifically

disclaims any implied warranties of merchantability, fitness for any

particular purpose and non-infringement. Multi-Tech Systems, Inc.

reserves the right to revise this publication without obligation to notify any

person or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registered

trademarks of Multi-Tech Systems, Inc. All other brand and product

names are trademarks or registered trademarks of their respective

companies.

MultiConnect®Cell 100 Series Cellular Modem

(MTC-LEU4)

MTC-LEU4 Quick Start

Quick Start Quick Start Quick Start

Installing a SIM Card

If you want to operate the modem on a particular cellular network, install a

mini-SIM card [or mini SIM (2FF) form factor].

To install the mini-SIM card:

1. Locate the mini-SIM card slot on the side of the cellular

modem. The slot is labeled SIM.

2. Push the mini-SIM card into the slot until it snaps into place.

Installing the Cellular Modem

1. Connect the suitable antennas to the antenna connectors

(CELL and AUX).

2. To connect to the serial interface on the cellular modem

(serial version only):

■Connect the DE-9 connector (9-pin) of an RS-

232 cable to the RS-232 connector on the

cellular modem.

■Connect the other end to the serial port on your

computer or other desired device.

■Screw on the power lead from the power supply

module into the power connection on the cellular

modem.

■Plug the power supply into your power source.

3. To connect to the USB interface on the cellular modem

(USB version only):

■Connect the mini-USB connector end of the

cable to the USB connector on the cellular

modem.

■Connect the other end of the USB cable to your

computer, either directly or through a hub.

4. After power is applied:

■The POWER LED lights after the device powers

up.

■When the LS LED begins to blink, the device is

registered.

Mounting Device

1. Locate the groove on the bottom of the cellular modem.

2. Slide the mounting rod through the groove.

3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.

Refer to the user guide for an illustration of the mounting

rod, as well as the dimensions for placement of the screws.

MultiConnect®Cell 100 Series Cellular Modem (MTC-

LEU4)

Document Part Number: 82103650L

This publication may not be reproduced, in whole or in part, without the

specific and express prior written permission signed by an executive

by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,

whether express, implied or by estoppels, with respect to the content,

information, material and recommendations herein and specifically

disclaims any implied warranties of merchantability, fitness for any

particular purpose and non-infringement. Multi-Tech Systems, Inc.

reserves the right to revise this publication without obligation to notify any

person or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registered

trademarks of Multi-Tech Systems, Inc. All other brand and product

names are trademarks or registered trademarks of their respective

companies.

Table of contents

Other Multitech Modem manuals

Multitech

Multitech MultiModem ZPX MT5634ZPX-PCI Series User manual

Multitech

Multitech Dragonfly Nano MTQN-MNG1-B02 Application guide

Multitech

Multitech MultiConnect microCell User manual

Multitech

Multitech MultiModem MT5600ZDX User manual

Multitech

Multitech MultiModem ZBA USB MT5634ZBA-USB User manual

Multitech

Multitech MTCBA-E-U User manual

Multitech

Multitech MultiConnect Cell 100 series User manual

Multitech

Multitech MultiModem MT5634ZBA-V-V92 User manual

Multitech

Multitech MT2834BA User manual

Multitech

Multitech MT128NTZLX Operator's manual

Multitech

Multitech RJModem MT5656RJ Instruction Manual

Multitech

Multitech MultiConnect Adapter User manual

Multitech

Multitech MultiModem MTCBA-E-GP User manual

Multitech

Multitech MultiModem GPRS with Ethernet Interface User manual

Multitech

Multitech MultiModemISDN MTA128ST-USB User manual

Multitech

Multitech SocketModem Application guide

Multitech

Multitech MultiModem GPRS with Ethernet Interface User manual

Multitech

Multitech V.92 Desktop Modems MultiModem ZDX User manual

Multitech

Multitech MultiMobile MT5634ZLX/FE User manual

Multitech

Multitech Multimodem MTCBA-G-F1 User manual

Multitech

Multitech MultiConnect Cell MTC-H5 User manual

Multitech

Multitech MultiModemDSVD User manual

Multitech

Multitech MultiModem CMDA MTCBA-C1X User manual

Multitech

Multitech SocketModem MT5600SMI User manual

Popular Modem manuals by other brands

RACOM

RACOM RipEX2-HS user manual

Digi

Digi XBee-PRO XSC RF Modem quick start guide

Intelbras

Intelbras WiFiber 1200R user manual

D-Link

D-Link DSL-24MF - POTS Filter Specifications

Encore

Encore ENDSL-A2+4R2 Specifications

Campbell

Campbell Redwing 100 instruction manual

Comtech EF Data

Comtech EF Data CDM-625A Installation and operation manual

Novatel

Novatel iPass MiFi 2200 quick start guide

GINEERS

GINEERS M-BUS Series instruction manual

Atlantis Land

Atlantis Land I-Storm USB ADSL modem A01-AU2 Multilanguage manual

KaiDeng

KaiDeng WVC Modem manual

Comtac

Comtac LP-3014PW Installation guide and user's manual

NETGEAR

NETGEAR A7000 quick start

Campbell

Campbell Sierra Wireless AirLink RV50 Quick Deploy Guide

Garnet

Garnet GAN-1021 install guide

BT Mini Wi-Fi Home Hotspot 500 user guide

CNET

CNET CN5614XR user manual

Patton electronics

Patton electronics 1180/35 user manual

Multitech MTC-LEU4 User manual

Popular Modem manuals by other brands