MWf GOLD LINE User manual

GOLD LINE
Gold line user manual
Metal and Water Finder
WWW.MWF-USA.COM
User’s Manual

Gold line user manual
Contents
Page 1
Metal and Water Finder
Contents
Technical specification
Safety information
Device parts
Interfaces and components of Device
Overview
Assembly
Setup wizard
Page 1
Page 2
Page 3
Page 5
Page 7
Page 8
Page 10
Page 11
Start searching Page 13
Notes Page 17

The user must practice before starting the detecting operations and
discoveries
Store in Cool and dry place 15-40 C 5%-75% humidity Read & Understand
The User's manual
before using this device
Page
Safety information
2
The operating in high voltage areas
would limit the results and
performance
Don't operate two devices with
same method of search at the
same place
The operator Must remove any
metals that might affect the
opreatin eg:Rings,watch, belt....
Any attempt to tamper the device
or unapproved maintenance
would void the warranty
Don't store in high temperature or
high humidity
It’s better to turn off mobile while
using the device.
Disconnect the batteries before
long time storage
For devices that work on
replaceable batteries, use good
quality batteries to work longer
hours.

Page
Technical specification
3
Bluetooth NO
Wireless: NO
Search system : Built-in ionic and radar search system
Operating processor: MICROCONTLLER PIC18
Operating frequency: 20 MHz
two celles lithium 3.7v - 3600 mAh / output 12v
Power consumption: Maximum of consumption 50 mA
Battery life: 10 work hours
Charger: 5.1 volt 3A / Charging Time 4 hours
Display Type: NO
Specialized to detects: Gold
Targets Discrimination: NO
Target Selection System: NO
Depth Search: 12 M
Distance Search: 50 M
Search principle: Processing the Signal Received level of ionic radiation
Results feedback: Light,sound and vibration alerts
Power:

Voice alerts:
Vibrating alert:
Operating temperature:
Storage temperature:
Humidity:
Weight:
Dimensions:
Bag dimensions:
Technical specification
Page 4
From -15° C to 60° C
From -15° C to 40° C
Compound: 700 g – disjointed in the bag: 1200 g
35X80X150 mm
130X290X340 mm
No
It can be stored and work in the degree rate of air humidity of
level 90%.
Automatic smart
guidance system:
Yes
Yes

This sensor needs to connect into its own entrance at the
front of the device by using connectivity socket.
Ion and Radar sensor.
The unit is responsible to control of the settings and search
options.
The batteries was built inside it.
Also it’s responsible to issuing the search acoustic ,optical and
vibrations results.
Main Control Unit
An electric charger to recharge the device's battery
Values: Input: 240-100VAC / 60-50Hz / 0.4 amps
Output: 5volts AC / 3amp / 15 Watt.
Charger
Device parts
Page 5
It uses for hold and control the device.
The hand held has laser button on the front section. and the
charging socket at the bottom
Hand held

Page
Needs to contact through the headphones jack, who is to the right
side of the device.
Headphones
Device parts
6

Page 7
1
2
3
4
5
Ionic sensor input
Night light
Visual signal indicator
Battery indicator
6
7
8
Ground calibration button
Volume button
LED button
1
6
8
7
2
3
4
5
Interfaces
ON/OFF key

Interfaces
1
2
1
1
Page 8
laser button
Charge socket

Connect
the Ionic Sensor to
the Main Unit
Headphones socket
2
1
Page 9
Device Aggregation

Starting
Page 10
LED ashlight button: press the button to turn the
ashlight in the front of the unit for ease of use in night.
Keep in mind that working with ashlight increases the
power consumption and therefore less working hours.
Volume button: press the button to select the sound level
Power button: Press and hold to turn on the unit after
switching the power switch ON.
Ground calibration key: With this key, the user can adjust
the unit to adapt to the terrain and environment in which
the device operates. The device gives the normal and
stable adjustment of the search tool for better results.
Note: We may start searching in an area where the device
is issuing a signal in general
We press the calibrate key once and wait for the signal to
stabilize
If this continues to sound in any direction we press the key
again until we get a stable result and then go to the search
area to determine the targets.
There are three levels to adjust the calibration if the device
is not calibrated. You are located in areas where there is
high noise from high voltage, etc.

Starting
Page 11
Soil
Target
Visual Indicator
Level
Audio Indicator
Level
To use the Verication Unit ,First move away from suspected target
location and calibrate the device by pressing the balance button, then
start moving around the target location. The unit will react according to
the target ionic eld indicating sound and visual signals.
The signal will increase when the unit is near the target.
The ionic eld intensity depends on the metal type and the period
that been underground.
Note:
Note:
The approximate depth of the target can be determined by using
this unit. After the target point is determined, direct the target to the
target and walk in any direction until the acoustic indicator is
disconnected. We measure the distance from this point to the target
point, which is the approximate distance to the depth of the target.

Charging
Page 11
LED
Indicator
Description
Battery Status while workingBattery Status while charging
Battery at 100%
Battery at 50%
Battery at 25%
Flashing Red: The battery is low
and the unit will shut-down
automatically
LED
Indicator
Description
Flashing Red: The battery is
starting to charge in rst stage
The red indicator stops ashing and the
yellow start to ash indicating the start
of the second stage of the charging
process
The yellow indicator stops ashing and
the green start to ash indicates the
third and nal stage of the charge
process
All lights on full battery charge
achieved disconnect the charger
Caution
-Charge the battery immediately after use.
-When the battery is full disconnect the charger.
-Only use the charge adapter that is attached with the
product.
-Charge and store the unit away from ammable objects.
-Turn the unit o after use and don’t leave it idle.
Charge Adapter for the Verication Unit :5V DC / 3-A 15W

Notes
Page 12

Metal and Water Finder
www.mwf-usa.com
[email protected]
+1 ( 708 ) 364 9602
United States of America - illinois
www.mwf-metaldetectors.com
[e-mail]
+90 ( 212 ) 222 0946
+90 ( 212 ) 222 0947
Turkey - istanbul