MyBinding Duplo V-580 User manual

Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Duplo V-580 Sheet
Cutter
Installation Manual

,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
M2-Y1050 1999. 01
Unpack the sheet cutter stand.
Carry out unpacking and installation in
a place that is safe for the work.
1.
Check that the package has the contents
listed below.
2.
Assemble the sheet cutter stand,
according to the drawing below.
Attach the casters with locks in the
positions shown below.
3.
Install the sheet cutter (V-580) to the
stand, as follows:
To lift the sheet cutter, hold it by its
bottom plate, at both sides. Lifting of
the sheet cutter should be performed
by 2 or more persons, not by 1 person
alone.
qMount the sheet cutter onto the stand, so
that the sheet cutter's rubber feet fit into
the holes in the top of the stand.
wScrew in the 2 screws to fasten the sheet
cutter to the stand.
Make sure that the sheet cutter is
securely installed to the stand.
4.
Be sure to lock the stand's casters after the
sheet cutter has been installed to the
stand.
Item
Top plate
Intermediate plate
Bottom plate unit
Side plate units
Casters with locks
Quantity
1
1
1
2
2
Casters 2
Screws (M5 12) 6
Screws (M6 12) 8
Screws with washers (M6 12) 16
Screws (M5 12)
Hole
Stand
Screw
(M6 12)
Screw
(M6 12)
Caster
with lock
Caster
Intermedi
ate plate
Screw with
washer
(M6 12)
Bottom plate unit
Screw
(M5 12)
Top plate Side plate unit Side plate unit
Screw with
washer (M6 12)
Sheet cutter (V-580)
Rubber
foot