Mylek MYH03-05E User manual

1| Page
LED Programmable Panel Heater
INSTRUCTION MANUAL FOR MODELS
MYH03-05E, MYH03-10E, MYH03-15E
& MYH03-20E
BEFORE USE:
Please read the instructions carefully. You must inspect the appliance including its
cable and plug for any signs of damage. If the product is damaged, DO NOT USE
and contact your supplier immediately for refund or replacement.
This product is only suitable for well insulated spaces or occasional use.

2| Page
General Information:
Thank you for choosing the Mylek LED weekly programmable
Panel heater with Open window function. Please take time to
carefully read and understand the entire instruction manual
before using the product and then save it for future reference. We
reserve the right for any errors in text or images and any
necessary changes made to technical data. If you have any
questions concerning operational or technical problems please
contact our Customer Services on 0800 091 3171.
BEFORE USING THIS HEATER:
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons. This includes but is not limited to the
following:
CAUTION:
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge of the product. The
appliance is to be operated by responsible adults only after
reading and understanding these instructions. Children should be
supervised at all times to ensure that they do not play with the
appliance. Children under 16 years should not operate the unit or
carry out maintenance and/or clean the unit. Any infirmed
persons in the vicinity of the unit should be accompanied by a
responsible and competent able bodied adult. Remove the
packing and make sure that the appliance is intact. If there is any
doubt concerning the integrity of the unit do not use the
appliance and contact our recommended after-sales service.

3| Page
Do not leave any packaging materials within easy reach of
children. Before switching on appliance check if the electrical
voltage and frequency of the circuit correspond to those
indicated on the appliance. Use the appliance only for the stated
purpose, namely as aheater for domestic use. Do not use
it for any other application as it could be dangerous.
Safety Instructions:
•The product is for indoor use only.
•The item should be used only as intended.
•Check item carefully before use. Do not switch on heater with
defects or damaged power cable.
•The appliance should be connected to the same voltage as
shown on the rating label and printed in the manual.
•The heater should only be plugged into grounded sockets.
•Before plugging in the heater, make sure it is switched off.
•Do not use the appliance near flammable liquids or any
flammable materials.
•The appliance must not be located immediately below a
socket outlet.
•If the power cable is damaged in any way, send it to the
nearest after sales service recommended by the manufacturer
for replacement.
•Do not connect the appliance to extension cables or multiple
outlets.
•Do not damage or knot the power cable.
•Before cleaning the appliance or carrying out any
maintenance switch off the heater, unplug from its power
source and leave to cool for 1 hour.

4| Page
•Never expose the appliance to external weather conditions
(rain, sun, etc.)
•The appliance must always be placed on a flat and stable
surface with the feet fitted correctly or fitted correctly to a
wall using the correct fixings.
•If the appliance is not being used switch it off. If any repair is
required please contact the after-sale centers approved by the
manufacturer.
•Do not touch heater with wet hands.
•Always unplug the item, before cleaning or if the item
becomes faulty.
•Never carry the heater by the power cable.
•When you switch off the heater unplug from the power source
by the plug. Do not pull on the cable to unplug from the
power source.
•Do not wrap the cable around the appliance after use.
•Children of less than 3 years should be kept away unless
continuously supervised.
•Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user
maintenance.
•CAUTION — Some parts of this product can become very
hot and cause burns. Particular attention has to be given
where children and vulnerable people are present.
•This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.

5| Page
•The appliance should only be connected to the same voltage
as printed on the rating label and manual.
•If used as a portable heater do not use in the immediate
surroundings of a bath shower or a swimming pool.
•WARNING: In order to avoid overheat i n g , d o n o t c o v e r t h e
heater.
•Never place foreign objects into the air vents.
Installation:
•The heater carries an IP24 waterproof rating, If this unit is to
be fitted in a bathroom then it must be “INSTALLED BY A
QUALIFIED ELECTRICIAN”.
•The LED panel heaters can be wall-mounted or floor standing.
•Mount feet on the base of the unit using the 4 screws provided
in accordance with Figure 1 making sure the screws are
securely tightened.
Figure 1
•Place the hanging bracket level against the wall as aguide
ruler (please make sure the holes are parallel level), use a
marker pen to mark the hole position. Image 1on Figure 2
below.

6| Page
•Drill holes on the wall with ɸ8mm drill bit and insert the
plastic wall plugs. Image 2 on Figure 2 below.
•Securely fasten the hanging bracket to the wall with the
screws provided. Make sure the hanging bracket is in the cor-
rect direction. Image 3 on Figure 2 below.
•Gently insert the bottom of the heater to the hanging bracket
first and then push the top of the heater body onto the hanging
bracket. It is good practice to try attaching the hanging brack-
et to the heater and taking off, so you are familiar with how it
attaches and detaches.
•When the heater is attached to the hanging bracket, secure in-
to place by turning the two plastic securing grips. Image 4 on
Figure 2 below.
Warning:
Be sure to keep a distance around the heater of at least 30cm
(300mm) see image below.
Warning! When drilling holes, always check to ensure there is no
wiring, pipework, water pipes etc in the area to be drilled.
Figure 1.

7| Page
Image 1 Image 2 Image 3 Image 4
Figure 2
Control Panel:
①Standby: on/off.
②Heating function
③Open window function
④Comfort mode
⑤ECO mode
⑥Timer
How to Operate:
•Plug the appliance into a AC 220-240V 50-60Hz socket, the unit will “beep”
once. The indicator light illuminates for standby mode.
•Press to turn on the heater. For the first use the heater is in factory default
settings as shown below: (If default settings are different, it will simply be be-
cause the unit has been quality tested after production).
Standby
Mode selection
Open window function
Increase function
Decrease function
Timer

8| Page
Heating mode: Comfort mode
Target temperature setting: 22 ℃
Day: 1(Monday), Time: 00:00 (Off)
Window open function: Off
Timer: Off
•Press to turn off the heater and put into standby mode when not in use.
•Unplug the product from the power source when not in use.
Setting the Clock and Current Day:
•Press for 3-4 seconds, the screen will flash “d”, press and to
choose the current day, 1 for Monday, 2 for Tuesday etc. When the current day is
reached press to confirm the current day setting.
1
Monday
2
Tuesday
3
Wednesday
4
Thursday
5
Friday
6
Saturday
7
Sunday
•After pressing to confirm the day setting the screen will display “H”. Press
and to set the current hour. When current hour is set press to con-
firm.
•After pressing to confirm the current hour setting the screen will display .
•Press and to set the current minute.
•Press to confirm all settings.
Please note: If the unit is in standby mode the unit will keep the clock and day
settings. Depending how long the unit is switched off at the mains or unplugged, the
clock and day may need to be reset when powered back up.

9| Page
Standard Heating Mode:
This mode can be used without the use of the weekly timer by choosing
Comfort mode or ECO mode. Press to select mode selection Comfort or
ECO. By pressing , heating mode runs in a continuous cycle as below:
•Comfort mode: Press and to set the temperature from 5-35℃.
• ECO mode: Press and to set the temperature from 1-31℃.
Note: ECO mode=Comfort mode - 4℃.
•Use of countdown timer: In standard heating ECO or Comfort mode you can
leave the model on permanent or programme the countdown timer so the unit
turns off after your set hours have elapsed, press the button once and the
“0H” will flash, using the or key choose your set hour from 1-24 hours,
once chosen press the and the display will revert back to your set
temperature, the will illuminate to show you have set the countdown timer.
The clock will countdown 1 hour at a time from your set hours and turn off when
your set hours have counted down. You can check the set countdown hours left
by simply pressing the once and once again to revert back to set
temperature.
•Anti-frost mode: Press the button until the screen displays . In this
mode you cannot set the countdown timer or adjust the temperature or set the
window open function. The target temperature is 7℃, if the room falls to 7℃or
below, the unit will operate. This is a preferred mode for garages, caravans etc.
Using the Preset programmes 1 and 2:
Note: Clock and day setting must be set for correct usage of P1/P2 programs. It is
advised to set day and clock in advance for the programmes to work correctly.
Programmes P1 and P2 are not adjustable and are pre-set.
To choose programme P1 or P2 below press the
button until P1 or P2 is chosen.

10 | Page
Set your preferred room temperature by pressing the or button. Once
temperature is chosen, the display will revert back to thechosen programme P1 or
P2. The unit will now operate in P1orP2programme.
See below for pre-set settings over a7 day period for programmes P1 and P2.
•P1 (Figure 1) is a preset programme Monday-Sunday. See image below for P1
preset programme which shows the unit settings in a 24hr period which will re-
peat over a 7 day period. (The image below (Figure 1) is just for illustration pur-
poses only and not shown on the LED display.)
P1: (Monday-Sunday) preset program.
00:00am – 01:00am comfort mode, 01:00am – 07:00am ECO mode and
07:00am – 00:00am comfort mode.
Figure 1
•P2 (Figure 2) is a preset programme Monday-Friday and Saturday -Sunday. See
image below for P2 preset programme which shows the unit settings in a 24hr
period which will repeat over a 7 day period. (The images (Figure 2 and 3) be-
low are just for illustration purposes only and not shown on the LED display.)
P2:(Monday-Friday) preset program
00:00am – 01:00am comfort mode, 01:00am – 05:00am ECO mode,
05:00am – 09:00am comfort mode, 09:00am – 19:00pm ECO mode,
19:00pm – 00:00am .
Figure 2
P2:(Saturday-Sunday) preset program
00:00am – 01:00am comfort mode, 01:00am – 08:00am ECO mode,
08:00am – 11:00am comfort mode, 11:00am – 13:00pm ECO mode,