NAPCO Gemini GEM-RP3DGTL User manual

1
OPERATING GUIDE for your
GEM-RP3DGTL KEYPAD
© NAPCO 2006
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
GEMINI
A 1 2 3
B 4 5 6
C 7 8 9 0
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
96
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
96
E
F
G
J
NEXT / YES
PRIOR / NO
AREA
OI249C 8/06

2
The GEM-RP3DGTL is a “smart”,
interactive, menu-driven keypad designed
for your Napco control panel. A digital
display is provided to show the status of
your system.
This booklet contains important
information about the operation of your
system with this GEM-RP3DGTL Keypad.
Read it carefully and keep it handy for
future reference. Check the Glossary for
an explanation of terms that may be
unfamiliar to you.
You'll probably find subjects mentioned in
this booklet that do not apply to your
system. Napco control panels have such
a wide variety of features that few security
systems, if any, will ever need them all.
Your alarm professional has chosen
appropriate features for your particular
needs.
Regardless of how your system has been
configured, rest assured that it has been
carefully designed and engineered to the
highest industry standards. To assure
optimum safety and security, familiarize
yourself with this equipment. Periodically
check its condition and state of readiness
by testing it at least once a week in both
the ac/battery and battery-only modes
(ask your alarm professional how to make
these tests).
INTRODUCTION
Test your sounding device and backup battery
1. While disarmed, press A.
2.Answer NO (press F) until “3” (Bell Test) appears in the
window.
3. Press YES (E) to execute the test. The alarm will sound
for about two seconds.
•If the alarm does not sound, call for service.
•If the battery is low, a system trouble E02 will appear in
the display. Allow 24 hours for the battery to recharge. If
the trouble continues, call for service.
Test your central station communicator
1. While disarmed, press A.
2. Answer NO (press F) until “15” (Telephone Test)
appears in the window.
3. Press YES (E) to send a test code to the central
station.
4. If the test is not successful, “E03” will display, indicating a
communication failure. Call for service.
IMPORTANT - TEST YOUR SYSTEM WEEKLY

3
TABLE OF CONTENTS
TABLE OF CONTENTS
Section Page
KEYPAD CONTROLS & INDICATORS............................................... 4
SETTING THE ALARM (ARMING) WHEN LEAVING .......................... 6
PROTECTING YOURSELF WHILE ON THE PREMISES ................... 8
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING...... 10
FIRE PROTECTION............................................................................ 11
KEYPAD FUNCTIONS ........................................................................ 15
CENTRAL-STATION MONITORING ................................................... 20
ADVANCED FEATURES .................................................................... 21
PROGRAMMING USER CODES ........................................................ 22
GLOSSARY ........................................................................................ 24
SYSTEM TROUBLE ERROR CODES ................................................ 27
TROUBLESHOOTING ........................................................................ 31
TO SILENCE AN ALARM, ENTER YOUR
CODE, AND PRESS J.
FOR SERVICE, CALL: __________________
CENTRAL STATION: __________________
EXIT DELAY: _________________________
ENTRY DELAY: ______________________
FIRE ALARM SOUND*:
________________________________
BURGLAR ALARM SOUND*:
________________________________
KEYPAD FIRE ENABLED? YES NO
KEYPAD PANIC ENABLED? YES NO
KEYPAD AUX. ENABLED? YES NO
*FIRE HAS PRIORITY OVER BURGLARY.

4
KEYPAD CONTROLS & INDICATORS
1
2
3
4
5
6
7
12
8
9
10
11
13
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
GEMINI
A 1 2 3
B 4 5 6
C 7 8 9 0
E
F
G
J
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
96
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
96
AREA
PRIOR / NO
NEXT / YES

5
KEYPAD CONTROLS & INDICATORS
Window. Lights indicate system
status messages; digit display
indicates related zone, function or
error message numbers.
STATUS Light. Lights (green) to
indicate that the system is ready
for arming. If a zone is not
secured, the light will be off and
the zone will display in the
window. If a zone has been
bypassed, the STATUS light will
blink while armed.
ARMED Light. Lights (red) to
indicate that the system is armed.
If an alarm has occurred, the
ARMED LED will be flashing.
FUNCTION Button. Selects
available system functions as
displayed in the window. The
selected function is executed by
pressing J, or YES (E).
BYPASS Button. (1) Deactivates
selected zones from the system.
(2) Unbypasses a bypassed zone.
(GEM-P3200/9600 panels only).
RESET Button. (1) Resets
various system troubles, displays,
etc. (See text.) (2) Resets
residential smoke detectors.
Numerical Keys (1-9, 0). Used to
enter codes, zone numbers, etc.
ON/OFF Button. Entry key.
Causes the entered code or
selected function to be executed.
INTERIOR Button. (1) Bypasses
all Interior Zones simultaneously
to allow free movement within the
premises. (2) Scrolls the window
display forward (NEXT). (3)
Answers “YES” to questions in
the window display.
INSTANT Button. (1) Cancels
entry delay on Exit/Entry Zones,
causing an instant alarm upon
violation. (2) Scrolls window
display backward (PRIOR). (3)
Answers “NO” to questions in the
window display.
AREA Button (G). Selects
other areas.
•Emergency Buttons. (Optional)
Used with the Gbutton to
signal an emergency, as follows:
•Press the 7and the G
buttons for Fire Emergency.
•Press the 8and the G
buttons for Auxiliary Emergency.
•Press the 9and the G
buttons for Police Emergency.
AC Light. Indicates AC Power is
present.
1
2
3
4
5
6
7
8
9
10
11
12
13

6
SETTING THE ALARM (ARMING) WHEN LEAVING
Arming the System
1. Check the keypad. The green STATUS light must be on in order to arm.
If the green light is off, the number(s) of any unsecured zone(s) will display in
the window. Refer to the pull-up zone list for the location of each problem
zone and secure by closing windows, doors, etc. When all zones are secure,
the green STATUS light will come on.
2. Arm the system. Enter your User Code followed by D. The green STATUS
light will go off, the red ARMED light will come on. Note: If you enter an
invalid code, the keypad will beep 4 times, indicating an error. Re-enter your
code.
3. Leave the premises. Leave through the exit door before the exit time expires.
Priority Arming
If you attempt to arm the system with a faulted Zone, a 3-second tone will sound
at the keypad and “P” will display in the window, indicating that the zones must be
secured before the panel can be armed.
Selectively Bypassing Zones
If you cannot locate or repair a faulted zone, it can be removed from the system,
or bypassed. Bypass the zone(s) from the system by pressing B, followed
by the zone number (or vice versa). The yellow BYPASS light will turn on to
indicate that the zone has been bypassed.
Note: Bypassed zones are unprotected. If a faulted zone cannot be secured,
have the system checked as soon as possible.
12 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
P INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

7
SETTING THE ALARM (ARMING) WHEN LEAVING
System Trouble If you attempt to arm with the SYS TBL light on, a 3-second tone will
sound and a “P” will display in the window. This indicates that the system has detected
a problem which may prevent it from operating properly. A number corresponding to the
trouble will then appear in the display. Refer to SYSTEM TROUBLE ERROR CODES
for descriptions of these troubles. If you cannot correct the problem immediately, press
Cand you will then be able to arm the system in this condition. Note: If you
cannot clear the trouble, have the system checked as soon as possible.
Area Arming (Optional)
In a system that has been partitioned into multiple areas, one or more areas may be armed while others remain disarmed.
Manager's Mode.
The Manager's Mode allows the user to arm / disarm other areas in a partitioned system. To arm a different area:
1. Press the numerical key representing the other area number.
2. Press Gfollowed by J. The keypad will now provide status and control of that area.
3. Enter your code followed by Jto arm.
4. Press Gfollowed by Jto return to the home area.
Global Arming (Optional) (Available only with the GEM-P9600/3200 panels)
To arm all areas simultaneously (including the area you are in), press 9, Gand enter your code followed by D.
To disarm all areas simultaneously, press 0, Gand enter your code followed by J.
•The User Code must be valid in all area(s).
•If any zone is not secured, the keypad will display “P”. All faulted zones in the respective area(s) must be secured or
bypassed. Note: If a system trouble is indicated, the system cannot be armed using this method.
P INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

8
Bypassing Interior Zones
Interior Zones, when bypassed, allow free movement within the home while the
protection of armed perimeter zones is maintained. To bypass Interior Zones, press
Eand enter your User Code followed by D. The red ARMED light will light and
the green STATUS light will blink, indicating zones bypassed. The INTERIOR and BYPASS lights will display in the window.
Your system may have provisions for two groups of Interior Zones. (Optional--Interior Groups programmed? YES NO)
•Press E, followed by Jto Bypass Interior Group 1: [ ____________________________________ ]
•Press Etwice followed by Jto Bypass Interior Group 2: [ ______________________________________ ]
•Press Ethree times followed by Jto Bypass both Interior Groups 1 & 2.
Automatic Interior Bypass (Optional - Automatic Interior Bypass programmed? YES NO)
Your system may have been programmed for Automatic Interior Bypass, which allows it to recognize that you have armed the
system and remained in the house, prompting it to automatically adjust the interior protection accordingly.
•If you arm the system and remain in the house, all Interior Zones are automatically bypassed. The INTERIOR and/or
BYPASS lights which will remain lit, indicating that it is safe to move about.
•If the system is armed and you leave, the Interior Zones will unbypass, providing complete interior protection.
Instant Protection
When retiring for the evening, after all family members are home, you can cancel the entry delay on the Entry Zone(s).
To arm with instant protection, press Fjust prior to arming, or at any time after the system is armed. When armed with
Instant Protection opening the entry door will cause an immediate alarm.
•When arming with Instant Protection, the exit delay will remain in effect, allowing exit of the house just after arming.
While armed, the red ARMED light will flicker rapidly to indicate instant protection.
PROTECTING YOURSELF WHILE ON THE PREMISES
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

9
PROTECTING YOURSELF WHILE ON THE PREMISES
Emergency Buttons (Only available if programmed)
The Blue Emergency Buttons (7, 8& 9), if programmed, are always
active, whether the system is armed or disarmed. The emergency signal will only be
transmitted when an Emergency Button and Gare pressed at the same time.
•Fire Emergency Simultaneously press 7and Gto alert the central
station of a fire emergency.* (Fire Emergency programmed? YES NO)
•Auxiliary Emergency Simultaneously press 8and Gto alert the central
station of an Auxiliary emergency.* (Auxiliary Emergency programmed? YES NO)
•Police Emergency Simultaneously press 9and Gto alert the central
station of a police emergency.* (Police Emergency programmed? YES NO)
Easy Exit (Optional - Easy Exit programmed? YES NO)
Your system may have been programmed for Easy Exit, which allows a user to exit the premises while the system is
armed. By activating Easy Exit while the system is armed, the Exit Delay countdown will take place, during which time
you are permitted to leave through the exit door. The Easy Exit Delay time will be identical to the Exit Delay time the
system gives you each time it is armed. This will allow, for example, an early morning commuter to exit the house,
without having to disarm and rearm the system, awaking the family.
Press Eto activate Easy Exit on your system. (GEM-P3200/GEM-P9600 V11D or less, GEM-P1632 V8G or less)
Press Dto activate Easy Exit on your system. (GEM-P3200/GEM-P9600 V20 or greater, GEM-P816/P1632 V9A or greater)
*Note: Discuss your Emergency
Features with your Installation
Company.

10
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING
Disarming the System
1. Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system
before your Entry Delay time expires.
2. Enter your User Code and press D. The red ARMED light will go out, indicating that the system has been disarmed.
•If you enter an invalid code, the keypad will beep 4 times, signifying an error. Re-enter your code immediately. 10 seconds
before Entry Delay expires, the keypad will emit a pulsing warning tone.
Alarm Indication / Silencing an Alarm
If the red ARMED light is flashing upon entry, an alarm occurred while you were out. (The display will scroll the number(s) of the
violated zone(s). Proceed with caution! If you suspect that an intruder may still be in the premises, leave immediately and call
authorities from a neighbor's phone.
To silence an audible alarm:
1. Enter your code and press J. After the system is disarmed, the window will continue to display the number(s) of the zone(s)
violated.
2. To reset the display, note the zones violated, then press C.
Ambush (Optional) Your Ambush Code Type is: TYPE 1 (Prefix) TYPE 2 (Unique) My Ambush Code is ___________________
If an intruder forces you to disarm your system, enter your Ambush Code and press J. There are two types of Ambush Codes: (1) A 2-
digit code (prefix) entered just prior to your normal User Code and (2) A separate and unique User Code.
Example Type 1 (Prefix): If your User Code is 1234 and your Ambush Code is 99, press 991234J.
Example Type 2 (Unique): If your User Code is 1234 and your Ambush Code is 8899, press 8899J
Using your Ambush Code will send a silent alarm to the central station. The red ARMED light will go out and the window will display
“SYSTEM READY” as if the system were normally disarmed. There will be no indication that a silent alarm has been sent.