NAPCO RPXP6GT User manual

XP-600 & RPXP6GT keypad
Control Panel/Communicator
Installation Instructions
WI1372 1/05
© NAPCO 2005
®

2
WI1372 XP-600 Installation Instructions
General Information
The NAPCO EXPRESS XP-600 control panel
provides up to 6 hardwired/wireless zones and 2-wire
fire. Up to six 4-digit user codes can be programmed.
Ambush, when selected, uses User 6 code as an
Ambush code.
The XP-600 is wireless ready. When used with a
GEM-RECV-XP8 receiver, the control panel can
support up to 6 wireless zones, 4 wireless smoke
detectors and 4 Keyfobs.
The RPX-6 keypad provides complete control of the
XP-600 control panel. Information on system status,
bypassed zones, system troubles etc. can be viewed
at the keypad.
The control panel can be easily and quickly
programmed from the keypad. The panel can also be
locally or remotely downloaded using PCD3000
software and a PCI 2000/3000 interface or PCL2000A
local Download cable. See Downloading Section
(page 5) for more information.
XP-600 Features
Control Panel
•6 Zones
•2-wire Fire Zone
•3 Keypad Panics
•Wireless Ready
•Bell Supervision
•Line Cut Detection
•Answering Machine Override (Second Call)
•50 Event Log
Communicator
•2 Telephone Numbers
•Backup Reporting
•Pager Format
•Point ID Format
•Individually Report 6 Users
•Opening after Alarm Report (Cancel Code)
•Conditional Closing Report
For Technical Assistance, Contact the NAPCO Toll Free Helpline !
[phone]
NAPCO Security Systems, Inc.
333 Bayview Avenue "Amityville, New York 11701
For Sales and Repairs, call Toll Free: [phone]
Table of Contents
General Information........................................... 2
XP-600 Features ............................................... 2
Specifications .................................................... 3
UL Compatible Smoke Detectors ...................... 4
Listings and Approvals ...................................... 4
Ordering Information ......................................... 4
Optional Accessories......................................... 4
Programming the Panel..................................... 5
Installation......................................................... 6
Wiring................................................................ 6
Keypad Operation ............................................. 7
Panel Operation ................................................ 8
Bypassing ......................................................... 9
User Program Mode.......................................... 10
XP-600 Commands........................................... 10
Dealer Commands ........................................... 11
Wireless Operation (Signal Strength) .............. 12
Zone Features................................................... 13
System Times ................................................... 14
System Features ............................................... 15
Telephone Number 1 Programming .................. 16
Backup Telephone Programming ...................... 17
Pager Programming .......................................... 18
Telephone Number 3 Programming .................. 18
Report Codes .................................................... 19
Enhanced Communicator Features................... 19
Wireless ............................................................ 20
Downloading ..................................................... 21
Dealer Programming ......................................... 22
System Troubles ............................................... 23
Troubleshooting ................................................ 25
XP-600 WIRING DIAGRAM .............................. 27

3
Specifications
Current & Voltage Ratings
Residential Burglary (4 Hour Standby)
Combined Standby Current: -------------- 500 mA
Bell Output: ----------------------------------- 2 A
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
Residential Fire (24 Hour Standby)
Combined Standby Current: -------------- 120 mA
Bell Output: ----------------------------------- 95 mA
(Using Rechargeable 12 VDC 7 AH BATTERY, minimal requirement)
Transformer and Battery
Required Transformer: -------------------- NAPCO TRF12 OR
BASLER 16.5 VAC 20VA
Required Battery: --------------------------- 12V 4 AH Rechargeable
Change Battery every 5 years or as required
Maximum Charging Current: ------------- 165 mA
Maximum Input Current:------------------- 2.58 A
Loop Characteristics
Loop Voltage: -------------------------------- 5 Volts
Loop Current : -------------------------------- Zones 1, 2, 3: 0.9 mA (2.2 K)
Zones 4, 5, 6: 0.5 mA (3.9 K)
Loop Resistance: ---------------------------- 100Ω per zone (max.)
Device Specifications
Max # keypads: ------------------------------ 4, RPXP6GT current = 65 mA
Max # of receivers: -------------------------- 2, GEM-RECV-XP8
current = 65 mA each
Max # of compatible
2-wire smoke detectors:-------------------- 10
Max Keypad wire length:------------------- 1000’ total wire length
Miscellaneous
Housing Dimensions : --------------------- 11" x 121/8"x 3"
(28 x 30.8 x 7.6) HxWxD
Shipping Weight: --------------------------- XP-600/4 15.5 lbs.
Operating Temperature: ------------------- 0-49ºC (32-120°F)

4
WI1372 XP-600 Installation Instructions
Mfg 4-Wire
Smoke Detector
Smoke Detector
Base
Sentrol 449AT
449C
449CRT
449CST
449CSRT
449CSST
449CLT
449CSLT
449CTE
741U
712U
722U
732U
711U
721U
721UT
731U
701U
702U
702RE
702RU
System
Sensor
1112
2112
2112T
2112TSRB
2100
2100T
1100
2-Wire
Smoke Detector
6 zone Control Panel with 2-wire fire
Keypad
Zone Doubling Resistor (2.2K & 3.9K)
Operating Instructions XP-600
Programming Instructions XP-600
XP-600
RPXP6GT
ZDR
OI301
WI1373
Ordering Information
Optional Accessories
*Wireless Receiver
Window/Door Transmitter
Keyfob Transmitter
Wireless Smoke Detector
Wireless PIR
Wireless Dual-Technology Sensor
Wireless Glass-Break Detector
Relay Board
Audio Verification Module
Downloading Software for IBM PC Compatibles
Software with Interface for IBM PC Compatibles
(includes PCL2000A local download cable)
Local Download cable
GEM-RECV-XP8:
GEM-TRANS2:
GEM-KEYF:
GEM-SMK:
GEM-PIR:
GEM-DT:
GEM-GB:
RB1000:
Veriphone:
PCD3000:
PCI2000/3000:
PCL2000A:
Listings and Approvals
UL HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM CONTROL UNIT
STANDARDS # 1023, 985
VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL DEVICE
European E.M.C. Regulations CE Certification
HARMONIZED STANDARDS: EN50081-1 and EN50082-1
EC DIRECTIVES: 89/336/EEC, Electromagnetic Compatibility Directive
UL Compatible Smoke Detectors
XP-600 Compatible Smoke Detectors
*Supports up to 8 zones, 4 Key Fobs, 4 Smoke Detectors

5
Programming the Panel
Refer to XP-600 Programming Instructions (WI1373)
Defaulting the Panel
1. Remove power from the panel.
2. Remove all wiring from terminal 15 (PGM)
and terminal 3.
3. Connect terminal 15 (PGM) to terminal 3.
4. Apply power to the XP-600 control panel.
5. After a few seconds the WARMED, X
READY and HSYSTEM TROUBLE LEDs
will flash.
6. The keypad will beep 3 times indicating the
panel default values have been loaded.
7. Remove wiring between terminal 15 (PGM)
and terminal 3.
8. Re-install original wiring for terminal 15
(PGM) and terminal 3.
Keypad Programming
Refer to WI1373 for information on keypad
programming.
Downloading
The XP-600 panel can be download/uploaded
with PCD3000 software using the Ring Method,
Answering Machine Override (Second Call) or
A6 Method of downloading. The panel can
also be automatically downloaded/uploaded
using PCD2000 Software running PCPreset.
For Site Initiated Downloaded, see Auto
Download ID Number [93].
Local Downloading
Wire as shown in Figure 1. Use the power up or
A6 method of establishing a connection. The
power up method is recommended if the panel is
attempting to report.
Remote Downloading
Wire as shown in Figure 2. The panel can be
remotely download/uploaded using any one of
the following methods:
1. The A6 method
2. Call-in method
3. Answering Machine Override (Second
Call)
4. Site-Initiated (PCPreset & A6 )
5. Automatic Downloading (Using PCPreset)
MODEM
J1
TO COMPUTER
J3
LOCAL
TO
PCI2000
J2
TO EXTERNAL
MODEM
J4
TELCO
J5 LINE
OUT TO
TELCO
FIGURE 2REMOTE DOWNLOAD
PGM
(-)
[phone] 19
+PWR GND GREEN
PHONETELCO
GREEN
RED
XP-600 Panel at the site
RINGTIP RING
RJ31X
TIP
GRY
BRN
PGM
(-)
[phone] 19
GREEN TIP RING
PHONE
PCL2000A
GREEN
RED
MODEM
FIGURE 1LOCAL DOWNLOAD
TIP RING
TELCO
GND+PWR
BLACKRED
NOTE:
Any programming in Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code
Lockout has been programmed the panel will not default
the Dealer Code.

6
WI1372 XP-600 Installation Instructions
Installation
Mounting the Panel
Mount the Panel close to an unswitched AC
source, a cold-water pipe ground, and a
telephone line connection.
Mounting the Keypad
A keypad should be located near an exit/entry
door. To remove the keypad from the backplate,
insert a small screwdriver into the square hole at
the bottom of the keypad. Pull up on the
screwdriver to pop off the cover.
Up to 4 keypads can be connected on individual
wire runs with #22 AWG wire with a maximum
total cable length of 1000 feet. Each keypad
draws approximately 65 mA.
Typical Fire Installation
(Where permitted by local codes)
Install smoke detectors outside each sleeping
area and on each floor, including the basement.
Install the living room and basement smoke
detectors near the stairway of the next upper
level. For increased protection, additional
detectors should be installed in areas other than
those required, such as the dining room,
bedrooms and utility room. Heat detectors,
rather than smoke detectors, are recommended
in kitchens, attics, and garages due to
conditions that may result in false alarms and
improper operation.
Refer to NFPA Standard 74 (National Fire
Protection Association, Batterymarch Park,
Quincy, MA 02269) for additional information,
including proper mounting methods.
Wiring
Grounding the Panel
Connect the control-panel EARTH GROUND
screw through a No. 16 AWG or larger wire to a
metal cold-water pipe. Do not use a gas pipe,
plastic pipe or AC ground connections. Use at
least #16 AWG wire. Connect a wire with a
ground lug crimped or soldered onto one end
and connect it to the EARTH GROUND screw in
the cabinet.
AC Power and Battery Wiring
Complete all wiring before connecting the
battery or AC Power. Do not plug the
transformer into a switched outlet.
Telephone Wiring
Wire as shown in the wiring diagram in the back
of this manual.
WARNING
The FCC restricts the use of this equipment on
certain telephone lines. Read the FCC
statement on the back of this manual to ensure
compliance.
FIGURE 3Typical Fire Installation
Keypad Wire Color Control Panel Terminal
RED 12 (+PWR)
BLACK 13 (GND)
GREEN 14 (GREEN)
TABLE 1 KEYPAD WIRING

7
Burglary Zone Wiring
NAPCO’s EZ Zone DoublingTM is simple. Each
terminal has 2 zones, use an E(2.2 K) type
Zone Doubling Resistor for the primary zone and
a Z(3.9 K) type Zone Doubling Resistor for the
secondary zone.
Wire zones as shown in the wiring diagram at
the back of this manual (page 27). All resistors
must be installed, even if the zone is not used. If
required, unsupervised open circuit devices may
be used instead of closed circuit devices.
Program the zone as an Open Circuit Zone [06]
(Zone Doubling Resistor required). If necessary,
use the voltage chart below to verify proper
voltages.
Fire Zone Wiring
Wire the Fire Zone as shown in the Wiring
Diagram in the back of this manual. An EOL
resistor must be installed, even if the Fire Zone
is not used.
PGM Wiring
The PGM is a switched negative output that is
activated depending on the programming option
(s) that have been selected [08], [23] - [25].
Connect the device controlled by the PGM
between +PWR and the PGM terminal
(maximum load of 50 mA).
Keypad Operation
Keypad zone LEDs indicate zone status. W
ARMED, XREADY and HSYSTEM LEDs
provide system status. The keypad sounder
provides feedback beeps for correct and
incorrect entries.
Keypad Sounder
3 QUICK BEEPS
Panel Armed (System ON)
Chime ON
Fault Find Mode ON
Keypad Sounder ON
Zone Bypassed
6 QUICK BEEPS
Panel Disarmed (System OFF)
Chime OFF
Fault Find Mode OFF
Keypad Sounder OFF
Zone Un-Bypassed
1 SECOND - STEADY TONE
Incorrect Code Entered
Invalid key entry
4 LONG BEEPS (PRIORITY CONDITION)
1. Entering an Arm Code with a faulted zone
(Not an Auto-Bypass Reentry Zone).
2. Entering an Arm Code when the Bell or
PGM is ON (Bell and PGM will turn OFF).
3. Arming with the Fire LED ON - reset
required. Press the Bkey.
Fire Zone Normal 13.0 V
Fire Trouble 13.8V
Fire 0.0 V
TABLE 4 VOLTAGE AT FIRE ZONE (Terminals
8&9)
Terminals 2.2 K Primary 3.9 K
3&4 Zone 1 Zone 4
5&4 Zone 2 Zone 5
6&7 Zone 3 Zone 6
TABLE 2 EZ ZONE DOUBLINGTM
Primary (2.2K) and Secondary (3.9K) zones normal 1.9 V
Secondary (3.9K) open 2.5 V
Primary (2.2K) open 3.2 V
Primary (2.2K) and Secondary (3.9K) open 5.0 V
Primary (2.2K) and/or Secondary (3.9K) shorted
(Sys. Trbl 7-Zone Trbl)
0.0 V
TABLE 3 VOLTAGE AT TERMINALS 3&4, 5&4,
6&7

8
WI1372 XP-600 Installation Instructions
Keypad LEDs
WARMED LED DEFINITION
Armed ON
Instant Mode Rapid Flash
Zone in Alarm Flashing
XREADY LED DEFINITION
Ready to be Armed ON
Zone faulted OFF
HSYSTEM LED DEFINITION
AC Failure Flashing
System Trouble(s) ON
FIRE LED DEFINITION
Fire Alarm Flashing
Fire Memory/*Fire Trbl ON
*See Note 1
AC LED DEFINITION
AC Present ON
AC Failure OFF
ZONE LED DEFINITION
Faulted Zone ON
Bypassed Zone Slow Flash
Zone in Alarm Flashing
Panel Operation
Arming (System ON)
Before arming the system close all protected
zones (unless programmed as Auto-Bypass
Reentry Zones). Enter a 4-digit Arm/Disarm
code, the keypad will provide a feedback beep
for each key pressed. If a valid Arm/Disarm
code is entered, the keypad will beep 3 times. If
an incorrect Arm/Disarm code is entered, the
keypad will sound a 1-second tone indicating an
incorrect entry.
Arming without Entry Delay (Instant
Mode)
Enter the A1to eliminate the entry delay.
The WARMED LED will flash rapidly to indicate
the panel is in Instant Mode. If an Exit/Entry
Zone is tripped while the panel is in Instant
Mode the panel will go into alarm immediately.
Arming/Disarming with a Keyfob
The system can be armed by pressing the K
key, and disarmed by pressing the Lkey on
the Keyfob. Zones programmed as Exit/Entry
Follower Zones can be bypassed when the M
or Nkeys on the Keyfob have been
programmed for Interior [81-84]. Zones
programmed as Home/Away with Delay Zones
can be armed regardless of the state of the Exit/
Entry Zones when the Mor Nkeys on the
Keyfob have been programmed for Full Set [81-
84]. To arm the system with all zones protected,
press the Kkey. Press and hold the Mor
Nkey for 1.5s to fully set the system (the LED
on the Keyfob indicates the Keyfob has
transmitted the signal). Program Keyfob/
Keyswitch Chirp [23-4] for an audible indication
of system arming and disarming.
Arming/Disarming with a Keyswitch
The system can be armed/disarmed by using a
momentary Keyswitch wired to Zone 6.
Program Keyfob/Keyswitch Chirp [23-4] for an
audible indication of system arming and
disarming.
Arming Instant with a Keyfob
The panel can be ARMED INSTANT when the
Mor Nkeys on the Keyfob have been
programmed for Instant [81-84]. To arm the
system with Instant protection press the K
key, then press and hold the Mor Nkey for
1.5s to arm the panel with INSTANT protection.
Disarming (System OFF)
After entering the premises through an Exit/
Entry Zone, the keypad will sound the Entry
* If Fire Trouble on Fire LED [96-4] has been enabled, a steady
Fire LED will indicate Fire Trouble.
NOTE:
Faulted Keyswitch or silent 24 hour zone normally do not
display at the keypad. If a silent 24 hour zone or Keyswitch
is faulted at the time of arming the faulted zone will display
only while the priority sound is ON.
NOTE:

9
Delay Tone. Enter a valid Arm/Disarm code. If
a valid Arm/Disarm code is entered, the keypad
will beep 6 times, indicating the panel has been
disarmed. The red Armed LED will go out. If an
incorrect Arm/Disarm Code is entered, the
keypad will sound a 1-second tone, indicating
incorrect entry. Press the Bkey and re-enter
the code.
Disarming after an Alarm (Alarm Memory)
The armed LED and the zone(s) that caused the
alarm will be be flashing. Disarm the panel.
The system is currently not detecting zone faults
or displaying system trouble. The zone(s) that
caused the alarm will continue to flash. The
Ready and HSYSTEM TRBL LEDs are out
indicating:
The system is displaying Alarm Memory.
Press the Bkey to clear Alarm Memory.
Bypassing
Automatic Bypassing
Home/Away with Delay Zones
This zone type has the following operation
depending on whether an Exit/Entry Zone has
been violated during the Exit Delay time.
Home
Exit/Entry Zone is not violated
Zones selected as Home/Away with Delay
Zones will be bypassed automatically.
Away with Delay
Exit/Entry Zone is violated
Zones selected as Home/Away with Delay
Zones will have a fixed 20-second entry
delay when violated before an Exit/Entry
Zone.
Full Setting the System with Automatic
Bypassing - Home/Away with Delay
Zones
From the Keypad
Press CBto return protection to
Home/Away with Delay Zones that have
been automatically bypassed. Three
minutes are allowed to walk through Exit/
Entry and Exit/Entry Follower Zones.
Using A Keyfob (GEM-KF)
All zones in the system can be armed
regardless of the state of the Exit/Entry
Zone when arming with a Keyfob and using
an AUX key programmed as Full Set.
Press Kand press and hold the Mor
Nkeys for 1.5s when leaving the
premises. All zones, including Home/Away
Zones are armed.
Bypassing a zone
Press the Ckey, then the zone number to be
bypassed. While the panel is DISARMED, the
bypassed zone LED will flash slowly; indicating
the zone has been bypassed. While the panel is
WARMED, the bypassed zones will only be
displayed if the Display Bypassed [21-3] option
has been selected.
Unbypassing a zone (Disarmed only)
Press the Ckey then the number of the
zone to be unbypassed.
Group Bypass
Press CCto Bypass all Exit/Entry
Follower Zones [02] or Home/Away Zones
[01] (only if the system is programmed
exclusively for Home/Away with Delay
zones).
.
Using A Keyfob (GEM-KF)
Hold the Mor Nkey on the Keyfob to
Bypass all Exit/Entry Follower Zones [02] or
Home/Away Zones [01] (only if the system is
programmed exclusively for Home/Away
with Delay zones).
User Program Mode
To prevent the loss of the User 1 Code, the
panel default program includes User 1 Code
Lockout [96-2].

10
WI1372 XP-600 Installation Instructions
To change the User 1 Code from its default
value of 1234, program the 4-digit User 1 Code
through Dealer Programming [95]. User 1 Arm/
Disarm code is also used to program User
Codes 2 - 6. By default, the User 1 code cannot
be re-programmed by the user.
If it is necessary to change the User 1 code, it
can be changed through downloading or Dealer
keypad programming. From Dealer Program
Mode, change the User 1 Code Lockout ([96-2]
LED=OFF) to disabled.
Entering User Program Mode
1. Enter A8
2. Enter User 1 Code
(1 2 3 4)
(Default)
While in User Program Mode the Armed,
READY and HSYSTEM Trouble LEDs will
continue to flash, follow the example below to
program User 2’s code to 1923.
User Mode Programming Example:
1.Press 2, Zone 2 LED will Flash
2.Enter 1923, Zone 2 LED will
continue to flash until the 4th digit is
entered. The keypad will beep 4 times
confirming a valid entry (Zone LED steady).
Deleting a User Code
Press the number of the User to be deleted, the
zone LED will be flashing indicating that the user
has been selected. Press A4, the LED
associated with the user will now be OFF.
Exiting User Program Mode
To exit User Program Mode press the bkey.
XP-600 Commands
User Commands
A1Bell Test
Enter this command to turn on the Bell, keypad
sounder and keypad LEDs for 2 seconds. The
battery is tested during a Bell Test, and
automatically every *24 hours to ensure proper
battery operation under load. The Alarm output
requires a battery in order to supply the
specified output. If the battery cannot sustain
the load, a low battery indication will be
displayed. A battery test is also performed on
power-up after a 3 minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
CC Group Bypass
Enter this command to bypass all Exit/Entry
Follower Zones or Home/Away Zones (only if
the system is programmed exclusively for
Home/Away with Delay zones).
A4Instant
Enter this command before or after arming to
remove the entry delay on Entry/Exit Zones.
The keypad ARMED LED will flicker rapidly.
Faulting a Exit/Entry Zone will result in an
immediate alarm.
A5Chime ON/OFF
Enter this command to turn chime ON/OFF.
The Keypad will chime on any zone that has not
been selected as an Exit/Entry Follower Zone,
Home/Away with Delay Zones, or 24 Hour Zone.
Zone LED Meaning
OFF User Arm/Disarm Code not programmed
Flashing User Arm/Code is currently being programmed
Steady User Arm/Disarm Code has been programmed
TABLE 5 ZONE LED DEFINITION-USER PROGRAM
MODE

11
A8+ User 1 Code - User Program
Mode
A9Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds will be silenced except for
keypad feedback beeps and Keypad Sounder
on Alarm.
User Commands - Optional
A 0 Easy Exit/Easy Arm
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones. Enter a0
to arm the panel. To disarm the panel a valid
Arm/Disarm code must be entered. Requires
Easy Exit/Easy Arm [21-2] to be enabled.
A3Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
15) for 5 seconds.
Dealer Commands
A6 Download (Programming
Required)
Establish a connection between the PCD phone
line and the Control Panel phone line. When
ready, tell the installer to arm, then disarm. Then
enter A6in order to establish a connection.
Phone connection to installer will go "dead" as
downloader and panel connect.
A7Fault Find ON/OFF
Hardwired Zone Operation
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored.
Wireless Operation
(Signal Strength)
While in Fault Find mode the keypad will provide
an audible (Table 6) and visual (Figure 5)
indication of each transmitter’s signal strength.
The signal strength metering is based on a scale
of 4 to 10, with 4 being marginal and 10 being
excellent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the
transmitter. See Table 6. Each beep is 1-
second long. The keypad will sound a short
beep for transmitters with signal strengths of 3
or less.
Signal Strength Logging Mode
The Signal Strength Logging Mode is a
troubleshooting tool which allows the collection
of signal strength information for all transmitters
on the system. Normally the Signal Strength of
Supervisory Signals are not logged; during
Signal Strength Logging Mode the signal
strength information for all supervisory signals
received over a two hour period will be saved to
the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour
test period where all supervisory signals will log
signal strength information.
TABLE 6 AUDIBLE SIGNAL STRENGTH INDICATION
FIGURE 5VISUAL SIGNAL STRENGTH INDICATION
5 6-74 8-10
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
SIGNAL STRENGTH KEYPAD SOUNDER
3 or less .25SBEEP
4 BEEP
5 BEEP BEEP
6-7 BEEP BEEP BEEP
8-10 BEEP BEEP BEEP BEEP

12
WI1372 XP-600 Installation Instructions
Remote Activation
Using NAPCO’s Quickloader Software
(Version 3.26 or higher), follow the
instructions below:
From the Status Screen
Press F6
Select Miscellaneous Control
Select Enable Signal Strength Logging
Uploading Signal Strength Information
from the Log
After approximately (2) two hours, re-establish
a connection with the panel. Signal strength
log information ranges from 1 to 10. The
logging of signal strength should appear
similar to the sample LOG below:
Zone Features
[00]Exit/Entry Zones
Delay allows exit and entry through an Exit/
Entry Zone after the system is armed
without setting off an immediate alarm. Exit
Delay allows the user to leave the premises
after arming. Entry Delay allows the user
time to enter and disarm. The entry delay
may be canceled by pressing a4.
[01]Home/Away with Delay Zones
Zones that automatically bypass at the
expiration of the exit delay if the EXIT/
ENTRY zone(s) are not violated. Zones of
this type have a three (3) minute power-up
delay, and do not display or cause an alarm
if faulted when the system powers up.
Pressing the bkey cancels the 3 minute
timer.
If Exit/Entry zone(s) are violated during the
exit delay, zones programmed as Home/
Away with Delay Zone(s) will have a fixed
20-second entry delay, if violated before the
Exit/Entry zone.
To eliminate this fixed 20-second entry
delay, also program zones as Exit/Entry
Follower Zones [02].
To return protection to zones of this type,
press cb from the keypad or Mor
Nfrom a Keyfob. Program the Keyfob
AUX 1 or AUX 2 button for Full Set [81-7].
[02]Exit/Entry Follower Zones
Entry Delay allows the user time to enter
and disarm. Allows exit after the panel is
armed without setting off an immediate
alarm and allows entry only if an Exit/Entry
Zone [00] has been violated first. Zones of
this type have a three (3) minute power-up
delay, and do not display or cause an alarm
if faulted when the system powers up.
Pressing the bkey cancels the 3 minute
timer.
Group Bypassing - Zones programmed as
Exit/Entry Follower Zones will be Group
bypassed if the ccis pressed while
disarmed or within the Exit Delay.
Auto Interior Bypassing - Also program
zones as Home/Away with Delay Zone(s)
[01] to automatically bypass at the expiration
of the exit delay if the EXIT/ENTRY Zone(s)
are not violated during the exit delay.
[03]Auto-Bypass Reentry Zones
Zones programmed as this zone type are
permitted to be faulted at the time of arming.
Once the zone is restored, while the control
panel is still armed, the zone will
automatically be unbypassed and any
subsequent violations of the zone will cause
If A0 is Entered during Exit Time, Home/Away with
Delay Zones will be automatically bypassed, even if the
Exit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] must
be enabled.
NOTE:
07/24/97 17:44 QL: Full Program Uploaded
07/24/97 17:42 QL: Technical Connection
(callback) Technician 2
07/24/97 15:23 Transmitter Status: GEM_SMK 1
(7A0DB5): SS=7
07/24/97 15:13 Transmitter Status: GEM_SMK 2
(768447): SS=8
07/24/97 15:13 Transmitter Status: Zone 2, SS=6
07/24/97 14:27 Trouble: RF Link, GEM_RECV 1
07/24/97 14:25 Panic: Keypad
07/24/97 14:25 Panic: Keyfob 1(933780) SS=8
07/24/97 14:25 Dealer Program Mode Entered
07/24/97 14:24 Instant: Keyfob 1(933780) SS=8
07/24/97 14:24 QL: Connection Terminated (10
MIN T/O)
07/24/97 13:13 QL: Full Program Downloaded
06/24/97 12:06 Open: User 2
06/24/97 12:06 Close: EasyArm
06/24/97 11:55 Trouble Restore: Low Battery,
GEM_SMK 2(768447) SS=8
06/24/97 10:21 Transmitter Status: GEM_SMK
(7A0DB5): SS=6

13
an alarm condition.
[04]24-Hour Protection
A zone that provides protection at all times,
whether or not the system is armed.
[05]40 ms Loop Response
Normally loop response is 750 ms, select
this option to change the loop response to
40 ms. The slower the loop response, the
less sensitive the system will be to
intermittents (swingers). The programming
option is not permitted for UL installations.
[06]Open Circuit Zones
Program this zone type if unsupervised
normally open circuit devices are required
The programming option is not permitted for
UL installations.
[07]Burg (Steady) Output
Enables the Bell Output on a zone trip for
each zone selected. The Bell Output will
remain ON for the length of time
programmed for Burg (Steady) Output [07]
or it will remain ON until turned off by
entering a valid Arm/Disarm Code; 0 means
output will stay ON until reset.
[08]PGM Output
Enables the PGM Output on a zone trip for
each zone selected. The PGM Output will
remain ON until reset.
[09]Selective Bypass
If programmed, selected zones will be able
to be bypassed by the User. By default, all
zones are permitted to be bypassed.
System Times
[10]Exit Delay
The delay time which permits exit through
an Exit/Entry Zone [00] after the system is
armed, allows a user to leave the premises
without setting off an immediate alarm. Exit
Delay may be programmed for up to 255
seconds (4¼ minutes); a value of 0 defaults
to 60 seconds.
[11]Entry Delay
Delay time permits entry through Exit/Entry
Zone(s) after the system is armed without
setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the
system. Upon entering, the keypad sounder
will sound a steady tone (Entry Sound) to
remind the user to disarm the system. Entry
Delay Time [11] may be programmed for up
to 255 seconds (4¼ minutes); a value of 0
defaults to 30 seconds. Entry Delay may be
canceled by pressing a4before or
after arming.
[12]Burg (Steady) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[13]Fire (Pulsed) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[14]Test Timer Interval
Program the interval, in days, between Test
Timer reports. Test Timer Interval may be
programmed from 1 to 255 days.
Normally Open Zone Wiring
Wire the normally
open contact
as shown (Zone 4).
EZ Zone DoublingTM
resistor
is required.
Program the
zone for
Open Circuit [06].
3.9K
(Z)
ZONE 1
(E)
2.2K
ZONE 4
FIGURE 6OPEN CIRCUIT WIRIING

14
WI1372 XP-600 Installation Instructions
[15]Line Cut Time-to-Fail
Enable this feature by programming the
delay time required to declare a line cut
failure. Programming 000 will disable line
cut detection.
[16]Wireless Supervisory Timer
A transmitter will send a transmission every
time it is tripped; when there is no activity,
the transmitter sends a supervisory
transmission about once an hour. If the
receiver does not receive any signal (either
a trip or a status) from a transmitter in the
time specified, a system trouble ‘RF
Supervisory Failure' will be indicated at the
keypad. Timer is programmable from 1-26
hours; 0 means NO supervision.
[17]Wireless Smoke Supervisory Timer
A smoke detector will send a transmission
every time it is tripped; when there is NO
activity, the smoke detector sends a
supervisory transmission about once an
hour. If the receiver does not receive a
signal (either a trip or a status) from a
transmitter in the time specified, a system
trouble ‘RF Supervisory Failure' will be
indicated at the keypad. The Supervisory
timer is programmable from 1-8 hours; 0
means NO supervision.
[18]Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the test
timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using NAPCO PCD3000 Downloading
Software. On power up the test timer is sent
immediately. Follow the commands below
to offset the test timer using Quickloader
Software:
From the Status Screen
•Press F6
•Select Miscellaneous Control
•Select Test Timer Offset
•Enter New Test Timer Offset: 12
hours
•Enter uto advance the test timer
due in time by 12 hours.
System Features
[20]Keypad Features 1
(1) Enable Keypad Fire (ee)
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
(2) Enable Keypad AUX (ff)
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
(3) Enable Keypad Panic (gG)
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 6th
User Code will send an Ambush report
when entered to disarm the system.
Additional Programming required:
Program User 6 Arm/Disarm Code.
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
[21]Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is
programmed.
(2) Exit/Entry with Urgency - select to give
an audible indication of Exit and Entry times.
During the last 10 seconds of entry and exit
time, the keypad sounds a distinct sound to
indicate the premises must be left or the
panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Program
to disable keypad beeping on valid code and
function entries.

15
[22]Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except 24 Hour Zones) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent
reporting.
(2) Easy Exit/Easy Arm - Enables A0
command. While the system is armed,
entering this command allows 3 minutes to
Exit through Exit/Entry and Exit/Entry
Follower Zones. Enabling this option also
enables Easy Arm, enter a0to arm
the system.
(3) Swinger Shutdown - Automatically
disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour
Protection zones: allows only 3 alarms and
2 restores per zone per arming before the
zone is disabled.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23]Programmable Output Features 1
(1) Audio Verification - Program to activate
the PGM during reporting. Select specific
zones for audio verification by programming
the required zones in PGM Output [08],
PGM Features 2 [24] and PGM Features 3
[25]. Connect the PGM to the VeriphoneTM
trigger low input.
(2) Access Output - Activates the PGM
output for 5 seconds using the A3
command.
(3) Follow Keypad Sounder - The following
keypad sounds will activate the PGM output:
Entry Sounder, Keypad Pulsing Sounder,
Keypad Output on Alarm, Chime, Fault Find.
(4) Keyfob/Keyswitch Chirp - Program to
chirp the PGM Output (1) one time when the
panel is armed or (2) two times when the panel
is disarmed. Wire as shown in Figure 7.
[24]Programmable Output Features 2
(1) IFire - Program to activate the PGM
on a Fire alarm.
(2) AUX - Program to activate the PGM on a
AUX alarm.
(3) Panic - Program to activate the PGM on
a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[25]Programmable Output Features 3
(1) YAC Fail - Program to activate the
PGM on the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the PGM
on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper,
Receiver JAM, Wireless Smoke Low
Battery, Wireless Smoke Supervisory Fail.
[26]Miscellaneous Features 2
(1) Momentary Keyswitch Arming -
Typically, connect a normally-open
Keyswitch across the zone AND its 3.3K
zone-doubling resistor.
(2) Reserved.
(3) Inhibit Fail-to-Communicate Display -
This option prevents the keypad from either
indicating or sounding when a Fail to
Communicate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the
keypad. Low Battery Reporting is not
inhibited. The programming option is not
permitted for UL installations.
Telephone Number 1 Programming
[30]Subscriber ID Number
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
N/ON/CCOM
BLK
RED
+AUX
Siren Driver
Steady Input
PGM
+AUX
K1
FIGURE 7KEYFOB/KEYSWITCH

16
WI1372 XP-600 Installation Instructions
then press the ikey to blank the last
digit.
[31]Telephone Number 1
Program the phone number to be dialed for
Telephone Number 1. Program the number
directly, just as it is entered on a TouchTone
phone. A fixed Dial Tone Detection (E) is
included prior to the Dialing Prefix (Block
Number 44). Programming an E is not
required for Telco 1, Telco 2 and Telco 3. If
dial tone detection is not desired select No
Dial Tone Detection in Communicator
Features [46-1]. Use the ikey to blank
out remaining digits in the phone number.
[32]Receiver Format
Select the receiver format to be used to
report for Telephone Number 1: Program a
0 to disable reporting to Telco 1.
[0] Disabled [4] Universal High Speed
[1] Ademco Slow [5] Reserved
[2] Radionics Slow [6] Point ID
[3] Silent Knight Fast [7] Pager
[33]Receiver Options
(1) 2300 Hz HS/Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the following
Receiver Formats: Ademco Slow, Radionics
Fast, Silent Knight Fast and Universal High
Speed. This is a sophisticated data format
used to enhance the speed and check the
accuracy of the received transmission. This
format should be used whenever the central
station has this capability. Instead of
sending a second round to verify correct
data, the panel sends a Sumcheck digit after
sending the Subscriber ID and Alarm Code.
(3) Single Digit - 3/1 Format. 3-digit
Subscriber ID number and a 1-digit Alarm
Code will be transmitted.
(4) No Handshake - (All receiver formats
except Pager Format). If programmed no
Handshake/Kissoff is required by the panel.
[34]Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35]Zone Restore Report, Telco 1
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless
programmed as silent zones.
[36]System Reporting, Telco 1
(1) Keypad Fire - Program to activate a
Keypad Fire report (ee).
(2) AUX/AMBUSH - Program to activate an
AUX or AMBUSH report (ff).
(3) Panic - Program to activate a Panic
report (gG).
(4) Test Timer - Program to activate a Test
Timer report.
[37]System Reporting, Telco 1
(1) YAC Fail Report - Program to activate
an AC Fail report (15 minute fixed report delay).
(2) Low Battery Report - Program to
activate a Low Battery report.
(3) *Trouble Report - Program to activate a
Trouble report.
(4) IFire Report - Program to activate a
Fire report.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper,
Receiver JAM, Wireless Smoke Low
Battery, Wireless Smoke Supervisory Fail.
Point ID format will report trouble(s) by
device and ID number.
[38]System Restore Report, Telco 1
(1) AC Restore - Program to activate an AC
Restore report.
(2) Battery Restore - Program to activate a

17
Battery Restore report.
(3) Trouble Restore - Program to activate a
Trouble Restore report.
(4) Fire Restore - Program to activate a Fire
Restore report.
[39]Opening/Closing Report, Telco 1
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send an Opening After Alarm (Cancel
Code) or Conditional Closing reports.
Backup Telephone Programming
[40]Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number
then press the ikey.
[41]Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. A fixed dial tone
detection (E) is included prior to the Dialing
Prefix [44]. Dial tone detection can be
disabled by programming No Dial Tone
Detection [46-1]. To program any additional
delay enter a "D" where required in the
phone number.
[42]Receiver Format (Telco 2)
Select the format that will be used to report
for Telco 2 (Backup reporting). Refer to
section [32].
[43]Receiver Options (Telco 2)
Refer to section [33] Receiver Options.
[44]Dialing Prefix
Dialing prefix for Telco 1, Telco 2, and Telco
3. Program if using an Outside access
number.
[45]Communicator Features 1
(1) Communicator Enabled - Program to
enable the communicator.
(2) DTMF with Rotary Backup - The first
attempt to communicate is dialed using the
TouchTone method of dialing, subsequent
attempts are dialed using the pulse method
of dialing. Disable this feature to dial using
only rotary dialing.
(3) DTMF only - All attempts to
communicate dial using the TouchTone
method of dialing.
(4) Backup Reporting to Telco 2 - After 2
attempts are made to communicate to Telco 1
the backup phone number is dialed (Telco 2).
[46]Communicator Features 2
(1) No Dial Tone Detection - Program to
disable dial tone detection for Telco 1, Telco
2 and Telco 3.
(2) 2:1 Rotary Dialing - Changes the make
break ratio when rotary dialing from 1.5:1 to
2:1.
(3) Backup if < 4 attemps - If Backup
Reporting [45-4] has been enabled, the
communicator will use Telephone Number 2
[41] for the remaining retries when there are
less than 4 retries remaining.
(4) Reserved
Pager Programming
If Pager Format ([32]and/or[42]and/or[52] =
7) is selected, pager data will be displayed
as shown in Figure 8. If Pager Format is
selected 4/2 format must be programmed
and Sumcheck is not permitted. If a PIN
number is required refer to Leading Digits
[47].
Pager Alarm data is the same as 4/2 format
with the exception that the 2 digit Report
Code is transmitted before the 4 digit
Subscriber ID.
000 033-1234
Leading Digits
Report Code
Subscriber ID Number
FIGURE 8DEFAULT PAGER DISPLAY

18
WI1372 XP-600 Installation Instructions
[47]Leading Digits
Pager PIN Number - If a PIN number is
required by the paging system, program the
PIN number in the Leading Digits location.
See sample program below.
If a 7-digit PIN number is required, program
the panel as follows:
[31]/[41]/[51] - Pager Telephone number
[32]/[42]/[52] - Select Pager Format
[47] - X X X X X X X C
Leading and Trailing digits can be letters B,
C or D. B = the * button on a telephone, C =
the # button on a telephone, D = 2 second
delay.
[48]Trailing Digits
Transmitted after alarm data. Refer to
section [47] for programming information.
[49]Pager Options
(1) Skip Alarm Data - Once pager format is
selected, program this option to skip alarm
data. If this option is selected, all the
programmed Leading and Trailing digits are
sent, but the event code and subscriber ID
are not transmitted. With this option
selected, a telephone number programmed
in Leading Digits or Trailing Digits would
send the telephone number to the pager
each time a report is sent.
(2) Reserved
(3) Reserved
(4) Reserved
Telephone Number 3 Programming
[50] - [59]
Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].
Report Codes
[60]Zone Report Codes
Report Code for Zones 1 through 6.
4/2 format - The Zone Report Code is the
1st digit of the report code sent, the second
digit is the zone number of the reporting
zone. For example, if zone 2 has a report
code of 3, the report code would be 32.
3/1 format - Sends only the report Code
and does not append it with the zone
number.
[61]Point ID Report Codes
Point ID Report Codes are defaulted to
Burglary for zones 1 through 8. Optionally,
Point ID codes for zones 1 through 8 can be
programmed as follows:
[1] Fire [7] Gas Alarm
[2] Panic [8] Heat Alarm
[3] Burglary [9] Reserved
[4] Holdup [A] Auxiliary
[5] General Alarm [B] 24 Hour
[6] Reserved
[62]Zone Codes
[62-1] Restore code - Zones 1 through 8.
The second digit of the restore code is the
zone number of the restored zone. For
example, if the Zone Restore Code [62] is
programmed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code - Conditional Closing
Reports. Zones that are bypassed at the
time of arming send this code along with the
zone number of the bypassed zone(s). For
example a conditional closing by User 2,
with zones 2 and 3 bypassed would be as
follows: 1234 C2
F2
F3
[63]System Report Codes
Program a 2-digit report code for Keypad Fire,
Keypad AUX, Keypad Panic, Test Timer, AC Fail,
Low Battery, Trouble and Fire.
[64]System Restore Code
The code sent when a system condition
restores. The second digit of the 2-digit
restore code is the second digit of the
7-digit PIN Number Terminating Digit (#)
Digits in Report Codes and subscriber IDs that are
programmed with "B" through "F" will be converted to "0"s.
NOTE:

19
System Report Code [63]. For example, if a
Low Battery System Report Code is F8 the
Battery Restore would be E8 (4/2 format).
[65]Opening and Closing Codes
Program Opening and Closing Codes for
Users 1 through 6. The second digit of the
report code is the number of the user that
armed or disarmed the system. For
example, if the Closing Code [65] is
programmed
with a C, the closing code for User 2 would
be C2 (4/2 format).
[66]Ambush Report Code
Program a 2-digit report code for Ambush.
To send an ambush report, program a User
Code for User 6, Program report User 6 as
Ambush [20-4] and Select reporting for
Telco 1 [36-2] and/or Telco 3 [56-2].
Enhanced Communicator Features
[67]Telephone Number 1
(1) Opening After Alarm (Cancel Code) -
When enabled, all users that are not
selected to report on Opening/Closing [39]
will report an Opening only when opening
after an alarm has occurred.
(2) Conditional Closing Telephone 1 -
When enabled, all users that are not
selected to report an Opening/Closing ([39],
[59]) will report a Closing only when zones
have been bypassed. The Zone Trouble
Code [62-2] is used to report zones that
have been bypassed at the time of the
closing report.
(3) Reserved
(4) Reserved
[68]Telephone Number 3
(1) Opening after Alarm (Cancel Code) -
see [67-1].
(2) Conditional Closing Telco 3 - see [67-1].
(3) Reserved
(4) Reserved
Wireless
Up to two receivers can be wired to the XP-
600. Each wireless transmitter can be
mapped to a zone. Only 1 wireless device
is permitted per zone, however, the use of
both hardwired and wireless on a zone is
permitted.
To Map a transmitter to a zone:
1. Enter the Programming Block Number
that the transmitter is to be mapped to.
2. Enter the 7-digit RF ID number directly,
just as it is shown on the device label.
After the 7th digit is entered the keypad
will beep.
A transmitter will send a transmission every
time it is tripped. The transmitter also sends
a supervisory transmission about once
every hour. If the receiver does not receive
a signal from a transmitter in the time
programmed in Wireless Supervisory Timer,
a system trouble ’RF Supervisory Failure'
will be indicated at the keypad.
Program Wireless Supervisory Timer [16] to
change the supervisory time from the default
of 12 hours.
The Signal strength of a transmitter can be
checked at the keypad (see A7Fault
Find Mode) or saved to the LOG (see Signal

20
WI1372 XP-600 Installation Instructions
Strength Logging Mode - pg. 11).
[71-76] Wireless Transmitters
Enter the RF ID# and the point number that
is to be mapped to the zone.
Programming Example
Map point 1 of a window door transmitter
with an RF ID# of 0012B0:0 to Zone 3.
1. Enter Dealer Mode.
2. Enter C(beeps) 73 (beeps)
3. Enter
012G20
0
4. Enter 1(beeps)
Note: If the RF ID# in step 3 is not entered
correctly the keypad will emit a 1 second
tone indicating incorrect entry. Repeat
steps 2 - 4 above.
[81] - [84] Wireless Keyfobs
The GEM-KF is a hand held wireless
transmitter capable of Arming and
Disarming the control panel and/or
activating 2 Auxiliary Functions. To activate
the auxiliary functions, press and hold the
Mor Nkey for 1.5 seconds (see WI752
for more information).
Enter the RF ID# and AUX 1 and AUX 2
options for each Keyfob.
AUX 1 & AUX 2
Programming Options:
1 Panic
Program a 1 in the AUX 1 and/or AUX 2
option to initiate a panic alarm when the
Mor Nbuttons on the Keyfob are
pressed.
Additional programming required:
Keypad Panic (GG) [20-3]
Panic Report to Telco 1[36-2] and/or Telco 3
[56-3].
Audible Panic (Optional) [21-1]
2 AUX
Program a 2 in the AUX 1 and/or AUX 2
option to initiate a AUX alarm when the M
or Nbuttons on the Keyfob are pressed.
Additional programming required:
Keypad AUX (FF) [20-2]
AUX Report to Telco 1[36-2] and/or Telco 3
[56-2].
3 Bell ON
Program a 3 in the AUX 1 and/or AUX 2
option to turn the Bell ON when the Mor
Nbuttons on the Keyfob are pressed.
Press the Lbutton to turn the Bell OFF.
4 PGM
Program a 4 in the AUX 1 and/or AUX 2
option to activate the PGM Output when the
Mor Nbuttons on the Keyfob are
pressed. Press the Lbutton to turn the
PGM Output OFF.
5 Instant
Program a 5 in the AUX 1 and/or AUX 2
option to activate Instant Mode when the
Mor Nbuttons on the Keyfob are
pressed.
6 Access on PGM
Program a 6 in the AUX 1 and/or AUX 2
option to activate the PGM Output for 5
seconds when the Mor Nbuttons on
the Keyfob are pressed.
Additional programming required:
Enable Access Output [23-2]
7 Full Set System
Program a 7 in the AUX 1 and/or AUX 2
option to Fully Set the System when the K
and the Mor Nbuttons on the Keyfob
are pressed, or when the Mor N
buttons are pressed when the system is
armed with Exit/Entry Follower Zones or
Home/Away with Delay Zones that have
been bypassed.