NEC NP03Wi User manual

ENG-1
NP03Wi
Installation Manual
Introduction ................................................................................... ENG-2
Read This Before Starting.............................................................. ENG-4
Features ........................................................................................ ENG-5
Packaged Items ............................................................................ ENG-6
Part Names ................................................................................... ENG-7
Setup Procedure ........................................................................... ENG-9
Troubleshooting........................................................................... ENG-15
Specifications .............................................................................. ENG-15
CONTENTS
Interactive White Board Kit

ENG-2
ENG-3
Introduction
Thank you very much for purchasing the NEC Interactive White Board (Model Name: NP03Wi).
By connecting to an NEC projector to this product, the white board or wall can be used as your interac-
tive white board.
The supplied stylus pen has a built-in super-capacitor charge storage. Charge the super-capacitor for
3 minutes before using the stylus pen for the first time.
This manual uses the example of connection with the UM330X.
HDMI is a trademark or registered trademark of HDMI Licensing LLC.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and
electronic products carrying the mark (left) must be disposed of separately from normal
household waste. When you dispose of such products, please follow the guidance of your
local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort
will help us reduce the wastes as well as the negative impact such as mercury contained
in parts to the human health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European
Union Member States.
Cautions
(1) Unauthorized reprinting of the contents of this manual is prohibited.
(2) The contents of this manual are subject to change in the future without notice.
(3) The contents of this manual have been prepared with scrupulous care, but please notify NEC
should you have any doubts or notice any mistakes or omissions.
(4) Please note that NEC will accept no responsibility whatsoever for claims for damages, lost earn-
ings, etc., arising from the use of this product, regardless of article (3) above.
(5) NEC will replace any manuals presenting incorrect collation or missing pages.

ENG-2
ENG-3
DOC Compliance Notice (for Canada only)
This Class B digital apparatus complies with Canadian ICES-003.
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit
EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply
with this government regulation could void your right to operate this equipment. This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveriscon-
nected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
U.S.Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Boulevard, Suite 1100
Itasca, Illinois 60143-1248
Tel. No.: [phone]
Type of Product: Interactive White Board Kit
Equipment Classification: Class B Peripheral
Model No.: NP03Wi
We hereby declare that the equipment specified above conforms to the technical
standards as specified in the FCC Rules.

ENG-4
ENG-5
Read This Before Starting
About the pictograms
To ensure safe and proper use of the product, this installation manual uses a number of pictograms to
prevent injury to you and others as well as damage to property.
The pictograms and their meanings are described below. Be sure to understand them thoroughly before
reading this manual.
WARNING
Failing to heed this pictogram and handling the product
erroneously could result in accidents leading to death or
major injury.
CAUTION
Failing to heed this pictogram and handling the product
erroneously could result in personal injury or damage to
surrounding property.
Examples of pictograms
The symbol indicates instructions urging caution (including warnings).
A concrete indication of the caution is given within the symbol.
The symbol indicates prohibited actions.
A concrete indication of the prohibited action is given within the symbol.
The symbol indicates required actions.
A concrete indication of the required action is given within the symbol.
WARNING
• Whenmountingorremovingthecameraunit,donotremoveanyscrewsotherthan
those specified.
• Donotdissembleorremodelthestyluspen.Donotgiveashocktothestyluspenor
bend it.
Installation environment
• Avoiddrippingorsplashingwaterneartheproduct.Ifwaterhasbeenspilledintothe
camera unit, contact your dealer.

ENG-4
ENG-5
Cautions on using the stylus pen
• Useaatandhardscreenwithascreensizeof100inchesorless.
• Somescreensurfacescanbescratchedbythestyluspentip.Beforeusingthestyluspen,testitin
an inconspicuous part of the screen to be sure the pen tip will not damage the screen surface.
• Donotusethestyluspeninthebelowmentionedareas.
It may cause of malfunction of the stylus pen.
- In the area direct sunlight strikes the screen surface and the camera unit.
- In the area light of halogen or filament lamps directly strikes the screen surface and the camera
unit.
- Inthe case, materials reects light is usedwithinthe stylus pen operationarea.(ex. screen
frame)
• Donotusethestyluspeninthebelowmentionedenvironment.Itmaycauseofmalfunctionofthe
stylus pen.
- When the infrared remote is used.
• Theguaranteedoperationtemperaturerangeforthefunctionofthestyluspenis5°to40°C(41°to
104°F).
• Disposingofthisproduct
When disposing of this product, contact your store of purchase or local government for instruc-
tions.
Features
• Interactiveelectronicwhiteboardfunction
With a drawing software, the white board or wall can be used as your interactive white board, and
you can take handwritten notes or draw pictures on the screen with the supplied stylus pen.
Supported projectors:
- UM330X, UM280X, UM330W, UM280W
- M352WS, M302WS, M332XS
• Oneormorepeoplecantakenotesordrawpictureswithstyluspensatthesametime
Two stylus pens come standard with the product. The stylus pen is also available as an option
(NP02Pi).
Up to 255 stylus pens can be used at the same time on the product.
However, this number will vary depending on drawing software you use.
For using drawing software, refer to the user manual included with the drawing software.
• AutoCalibrationfunction
Position adjustment is easily done thanks to the auto calibration function.

ENG-6
ENG-7
Packaged Items
Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
• Cameraunitx1
• Adapter(24F5014☐) x 1
(Supported models: M352WS/M302WS/
M332XS)
• Adapter(24F5012☐) x 1
(Supported models: UM330X/UM280X/
UM330W/UM280W)
• Adapter cover (24F5013
☐
) x 1
(Supported models: UM330X/UM280X/
UM330W/UM280W)
The adapter and the adapter cover for
UM330X/UM280X/UM330W/UM280W
are attached together before shipment.
• Styluspenx2
• USBcablex1
For charging the stylus pen
• USBcable(4.5m/14.8feet)x1
For connecting the computer with the
camera unit
• InstallationManual(thisdocument)x1
• Screw(M3)x3
NOTE
• Downloadthedriverandthecalibrationsoftwarefromourwebsitetoinstallthemonthecomputer.
URL: http://www.nec-display.com/dl/en/index.html
• Drawingsoftwareisrequiredtousetheinteractivewhiteboardfunction.
No drawing software is included with the product. Get commercially available drawing software.

ENG-6
ENG-7
Part Names
Camera unit
Stylus pen
USB cable
Computer
Projector
Screen or whiteboard
The drawing shows an example of the optional
wall mount unit (Model name: NP04WK) with the
projector mounted on it.

ENG-8
ENG-9
Part names of the supplied stylus pen
Pen tip
Indicator (LED)
Charging port (USB)
Charging the stylus pen
Use the supplied USB cable for charging the stylus pen to connect the charging port (USB) of the stylus
pen with the USB port of the computer.
The stylus pen will start charging. Charging will complete in about 3 minutes.
• PressingthepentipagainstascreenorwhiteboardwillturntheindicatorLEDtored,whichindicates
that charging is completed and you are ready to use the stylus pen. If the red LED turns off, charge
the stylus pen.
Cautions on using the stylus pen
• Donotdamagethestyluspenbydroppingitontheoorormishandlingit.
• Keepthestyluspenawayfromwaterandotherliquids.Ifthestyluspengetswet,wipethestyluspen
dry immediately.
• Avoidheatandhumidwhenpossible.

ENG-8
ENG-9
Setup Procedure
Setup Flow
1. Mount the camera unit onto the projector.
 •ForUM330X/UM280X/UM330W/UM280W
 •ForM352WS/M302WS/M332XS
2. Connect the projector to the computer.
3. Turn on the projector power and adjust the position and focus of the projected
image.
4. Connect the computer and the camera unit with the included USB cable.
5. Download and install the driver and the calibration software on the computer
to perform the calibration.
1. Mount the camera unit onto the projector.
Two kinds of adapters are included. One is for UM330X/UM280X/UM330W/UM280W and the other for
M352WS/M302WS/M332XS.
• For UM330X/UM280X/UM330W/UM280W:
Use the camera unit, adapter (24F5012☐), adapter cover (24F5013☐), and two screws.
Preparation:
• Prepareaplus-headedscrewdriver.
• Ifthecablecoverisattachedtotheprojector,removeit.
To attach and remove the cable cover, follow the procedure provided in the user’s manual included
with the projector.
• TheadapterandtheadaptercoverforUM330X/UM280X/UM330W/UM280Wareattachedtogether
before shipment.
Before working, push and pull the top of the adapter cover to separate them each other.
1
2

ENG-10
ENG-11
1. Attach the adapter to the cable cover.
Engage the two protrusions of the adapter with the tab holes of cable cover and align the screw
hole of the cable cover with the one of the adapter.
Tighten the screw inside the cable cover.
12
2. Attach the cable cover to the projector.
3. Connect the USB cable to the camera unit.
Insert the L-shaped connector of the included USB cable (4.5 m/ 14.8 feet) into the USB port
(type B) of the camera unit.

ENG-10
ENG-11
4. Attach the camera unit to the adapter.
Engage the two protrusions of the camera unit in the holes of the adapter to align the screw
hole.
Tighten the screw to ensure safety.
5. Attach the adapter cover to the adapter.
Engage the two tabs of the lower end of the adapter cover in the mounting holes of the adapter
and push them until they click into place. Put the USB cable inside the adapter cover.
1
2

ENG-12
ENG-13
• For M352WS/M302WS/M332XS:
Use the camera unit, adapter (24F5014☐), and two screws
Preparation:
• Prepareaplus-headedscrewdriver.
1. Attach the camera unit to the adapter.
Engage the two protrusions of the camera unit in the holes of the adapter to align the screw
hole.
Tighten the screw to ensure safety.
2. Attach the adapter to the projector.
Engage the two protrusions of the adapter in the holes of the projector to align the screw
hole.
Tighten the screw to ensure the safety.
NOTE
• Donotallowthescrewstobeloosened.Doingsomaycausethecameraunittofall,resulting
in personal injury.
• Donotholdthecameraunittolifttheprojector.Doingsomayresultindamagetothecamera
unit, causing failure or malfunction.

ENG-12
ENG-13
2. Connect the projector to the computer.
The projector can be connected to a computer using the computer cable (supplied with the projec-
tor) or a commercially available HDMI cable.
3. Turn on the projector power and then adjust the position /
focus of the projected image.
For the adjustment procedure, see the projector user’s manual.
4. Connect the computer and the camera unit with the included
USB cable.
Insert the L-shaped connector of the included USB cable (4.5 m/ 14.8 feet) into the USB port (type
B) of the camera unit and insert the other end into a USB port (type A) of the computer.
For UM330X/UM280X/UM330W/UM280W, insert the L-shaped connector of the supplied USB
cable into the USB port of the camera unit in advance according to Step 3 of the section “1. Mount
the camera unit onto the projector.”

ENG-14
ENG-15
UM330X/UM280X/
UM330W/UM280W
M352WS/M302WS/
M332XS
5. Download the driver and the calibration software and install
them on the computer for calibration.
Download the driver and the calibration software from our website and install them on the computer.
URL: http://www.nec-display.com/dl/en/index.html
The operation on installing and calibrating is available in PDF (Portable Document Format).
To view or print the PDF files Adobe Reader™ is required.
If you cannot open a PDF file on your computer, obtain the current version of Adobe Reader for
your OS from the home page of Adobe Systems and install it on your computer.
NOTE
• Drawingsoftwareisrequiredtousetheinteractivewhiteboardfunction.
No drawing software is included with the product. Get commercially available drawing software.

ENG-14
ENG-15
Troubleshooting
Stylus pen does not work.
• IstheUSBcableconnectedbetweenthecomputer(typeAUSBport)andthecameraunit(typeB
USB port)?
• Havethedriverandthecalibrationsoftwarebeeninstalledonyourcomputer?
• Areyouusingthestyluspeninoneofthefollowingenvironment?
- If direct sunlight strikes the screen surface and/or camera unit, change the installation place where
it is not exposed to direct sunlight.
- If light of a halogen and/or a filament lamp strikes the screen surface and/or camera unit, change
the installing direction of the screen and/or camera unit, or block off lamp light.
- Donotuseascreenwhosematerialofframereectslight.
 InuenceofexternallightisdescribedatthetroubleshootingintheNP03Wisoftwareguide.Refer
to the software guide on the support page for our projectors uploaded in our web site and set them
upinanappropriateplacewheredoesnotgetinuenceoflight.
• Isthecameraunitsettothecorrectposition?
• Doesthestyluspenhavepropercharge?
If pressing the pen tip will not turn LED to red, charge the stylus pen.
• Isthescreensizeandusagetemperaturewithinappropriaterange?
Use a screen within the effective range.
Usethestyluspenwithinatemperaturerangeof5°to40°C(41°to104°F).
• Isthelensofthecameraunitsoiled?
 Ifthelensissoiled,wipeitwithasoft,dry,non-uffycloth.
Lines traced with the stylus pen do not match screen.
• Hasthesensorbeenproperlycalibrated?
• Ifperformingthecalibrationautomaticallywillnotresolvetheproblem,trytoperformthecalibration
manually.
Specifications
Camera unit
• Inputterminal:USBTypeB×1
• Powerconsumption:145mA/5V,725mW
• Weight:70g/2.5oz
• Externaldimensions:135(W)x35(H)x36(D)mm/5.3"(W)x1.38"(H)x1.4"(D)(notincludingprotru-
sions)
• Effectiverange:60"to100"
• Operatingtemperatureandhumidity:5°to40°C(41°to104°F)/20%to80%(non-condensing)
• Storagetemperatureandhumidity:−10°to50°C(14°to122°F)/20%to80%(non-condensing)
Stylus pen
• Weight:25g/0.9oz
• Powersupply:Chargingtype(supercapacitor)
• Chargingtime:3minutes
• Estimatednumberofchargingthebattery:100,000
• Operatingtime:about2hours
• Operatingtemperatureandhumidity:5°to40°C(41°to104°F)/20%to80%(non-condensing)
• Storagetemperatureandhumidity:-20°to80°C(-4°to176°F)/20%to80%(non-condensing)

GER-1
NP03Wi
Installationshandbuch
Einführung..................................................................................... GER-2
Bitte vor Beginn lesen.................................................................... GER-3
Merkmale ...................................................................................... GER-4
Enthaltene Teile.............................................................................. GER-5
Teilebezeichnungen ....................................................................... GER-6
Setup-Verfahren ............................................................................ GER-8
Fehlerbehebung .......................................................................... GER-14
Technische Daten ........................................................................ GER-14
INHALT
InteraktivesWhiteboard-Set

GER-2
GER-3
Einführung
VielenDankfürdenKaufderinteraktivenTafelvonNEC(Modellname:NP03Wi).
Durch Anschluss eines NEC-Projektors an dieses Produkt kann die Tafel oder Wand als Ihre interaktive
Tafel verwendet werden.
Der beiliegende Eingabestift verfügt über einen eingebauten super-Kondensator-Ladespeicher. Laden Sie
den super-Kondensator für 3 Minuten auf, bevor Sie den Eingabestift zum ersten Mal verwenden.
IndiesemHandbuchwirdalsBeispieleineVerbindungmitdemUM330Xverwendet.
HDMI ist ein Warenzeichen oder eingetragenes Warenzeichen von HDMI Licensing LLC.
Entsorgung Ihres benutzten Gerätes
Die EU-weite Gesetzgebung, wie sie in jedem einzelnen Mitgliedstaat gilt, bestimmt, dass
benutzte elektrische und elektronische Geräte mit dieser Markierung (links) getrennt vom
normalen Haushaltsabfall entsorgt werden müssen.
Folgen Sie beim Entsorgen eines solchen Gerätes bitte den Anweisungen Ihrer örtlichen Be-
hörde und/oder konsultieren Sie den Händler, bei dem Sie das Gerät erworben haben.
Nach der Sammlung benutzter Geräte werden diese erneut verwendet und entsprechend
den Umweltbestimmungen recycelt. Das trägt dazu bei, die Abfallmenge zu reduzieren
sowie die negativen Auswirkungen beispielsweise von in Teilen des Geräts enthaltenem
Quecksilber auf die Gesundheit und die Umwelt möglichst gering zu halten.
Die Markierung auf elektrischen und elektronischen Geräten gilt nur für die gegenwärtigen
Mitgliedstaaten der Europäischen Union.
Vorsichtsmaßnahmen
(1) EineunerlaubteVervielfältigungdesInhaltsdiesesHandbuchsistuntersagt.
(2) Der Inhalt dieses Handbuchs kann ohne Ankündigung geändert werden.
(3) Der Inhalt dieses Handbuchs wurde mit großer Sorgfalt zusammengestellt. Informieren Sie jedoch
bitte NEC, sollten Sie Zweifel haben oder Fehler oder Auslassungen bemerken.
(4) BittebeachtenSie,dassNECkeineVerantwortungfürSchäden,Umsatzverlusteusw.übernimmt,
dieaufgrundderVerwendungdiesesProduktsentstehen,unabhängigvonArtikel(3)oben.
(5) NEC wird alle Handbücher ersetzen, die eine fehlerhafte Kollation oder fehlende Seiten aufwei-
sen.

GER-2
GER-3
Bitte vor Beginn lesen
Über die Piktogramme
Um einen sicheren und ordnungsgemäßen Betrieb des Produkts zu gewährleisten, werden in diesem
HandbuchverschiedenePiktogrammeverwendet,diebeiderVermeidungvonVerletzungenfürSieoder
Dritte sowie von Sachschäden helfen sollen.
Die Piktogramme und ihre Bedeutungen werden unten beschrieben. Stellen Sie sicher, dass Sie sie
vollständig verstehen, bevor Sie dieses Handbuch lesen.
WARNUNG
Die Nichtbeachtung dieses Piktogramms und eine unsach-
gemäßeHandhabungdesProduktskönnenzuUnfällen
undschwerenVerletzungenoderzumTodführen.
VORSICHT
Die Nichtbeachtung dieses Piktogramms und eine unsach-
gemäße Handhabung des Produkts können zu Verletzun-
genoderSachschädeninderUmgebungführen.
Beispiele für Piktogramme
Das -SymbolzeigtAnweisungenan,diezuerhöhterVorsichtmahnen(einschließ-
lich Warnungen).
EinkonkreterHinweis auf die nötige Vorsichtsmaßnahme wirdin dem Symbol
gegeben.
Das -SymbolweistaufuntersagteVorgehensweisenhin.
Ein konkreter Hinweis auf die untersagte Handlung wird in dem Symbol gegeben.
Das -Symbol weist auf notwendige Tätigkeiten hin.
Ein konkreter Hinweis auf die notwendige Tätigkeit wird in dem Symbol gegeben.
WARNUNG
• WennsiedieKameraeinheitmontierenoderentfernen,entfernenSiekeineanderen
Schrauben als die angegebenen.
• ZerlegenodermodizierenSiedenEingabestiftnicht.SetzenSiedenEingabestiftkeinen
Stößen aus und biegen Sie ihn nicht.
Installationsumgebung
• VermeidenSietropfenoderverspritzenvonWasserinderNähedesProdukts.Wenn
Wasser in die Kameraeinheit verschüttet wurde, wenden Sie sich an Ihren Händler.

GER-4
GER-5
Vorsichtsmaßnahmen bei der Verwendung
des Eingabestifts
• VerwendenSieeineebeneundfesteProjektionsächemiteinerBildschirmgrößevon100Zolloder
weniger.
• MancheBildschirmoberächenkönnenvonderSpitzedesEingabestiftsverkratztwerden.Bevor
Sie den Eingabestift verwenden, testen Sie ihn an einer unauffälligen Stelle des Bildschirms, um
sicherzustellen,dassdieSpitzenichtdieBildschirmoberächebeschädigt.
• VerwendenSiedenEingabestiftnichtindenuntengenanntenBereichen.
Dies könnte zu Fehlfunktionen des Eingabestifts führen.
- IneinemBereich,indemdirektesSonnenlichtaufdieBildschirmoberächeunddieKameraeinheit
trifft.
- In einem Bereich, in dem das Licht von Halogen- oder Glühlampen direkt auf die Bildschirmober-
ächeunddieKameraeinheittrifft.
- IndemFall,dasslichtreektierendeMaterialienimAnwendungsbereichdesEingabestiftsverwendet
werden. (z. B. Bildschirmrahmen)
• VerwendenSiedenEingabestiftnichtinderuntengenanntenUmgebung.DieskönntezuFehlfunk-
tionen des Eingabestifts führen.
- Bei Benutzung der Infrarot-Fernbedienung.
• DergarantierteBetriebstemperaturbereichfürdieFunktiondesEingabestiftsliegtzwischen5°Cund
40°C.
• EntsorgungdiesesProdukts
Für Anweisungen zur Entsorgung dieses Produkts wenden Sie sich an Ihren Händler oder die örtlichen
Behörden.
Merkmale
• InteraktiveelektronischeTafelfunktion
Mit einer Zeichen-Software kann die Tafel oder Wand als Ihre interaktive Tafel verwendet werden, und
Sie können mit dem mitgelieferten Eingabestift auf dem Bildschirm Notizen von Hand schreiben oder
Bilder zeichnen.
Unterstützte Projektoren:
- UM330X, UM280X, UM330W, UM280W
- M352WS, M302WS, M332XS
• Eineoder mehrerePersonen können mit Eingabestiften gleichzeitig Notizen machen oder Bilder
zeichnen
Zwei Eingabestifte werden standardgemäß mit dem Produkt geliefert. Der Eingabestift ist ebenfalls
optional erhältlich (NP02Pi).
Bis zu 255 Eingabestifte können gleichzeitig mit dem Produkt verwendet werden.
Diese Anzahl kann jedoch abhängig von der von Ihnen verwendeten Zeichen-Software variieren.
 FürdieVerwendungderZeichen-Software,lesenSiebittedasBenutzerhandbuch,dasderZeichen-
Software beiliegt.
• AutomatischeKalibrierungsfunktion
Die Positionsanpassung ist dank der automatischen Kalibrierungsfunktion einfach durchführbar.