NEC NP04Wi User manual

NP04Wi
Installation Manual English
Deutsch
Français
Italiano
Español
Português
Русский
Türkçe
Polski
한글
日本語
Interactive White Board Kit

ENG-1
NP04Wi
Installation Manual
Introduction ................................................................................... ENG-2
Read This Before Starting.............................................................. ENG-4
Notes ............................................................................................ ENG-5
Disposing of this product............................................................... ENG-5
Features ........................................................................................ ENG-5
Packaged Items ............................................................................ ENG-6
Part Names ................................................................................... ENG-7
Setup Procedure ........................................................................... ENG-9
Troubleshooting........................................................................... ENG-15
Specifications .............................................................................. ENG-15
CONTENTS
Interactive White Board Kit

ENG-2
ENG-3
Introduction
Thank you very much for purchasing the NEC Interactive White Board (Model Name: NP04Wi).
By connecting to an NEC projector to this product, the white board or wall can be used as your interac-
tive white board.
The supplied stylus pen has a built-in super-capacitor charge storage. Charge the super-capacitor for
3 minutes before using the stylus pen for the first time.
This manual uses the example of connection with the UM351W.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and
electronic products carrying the mark (left) must be disposed of separately from normal
household waste. When you dispose of such products, please follow the guidance of your
local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort
will help us reduce the wastes as well as the negative impact such as mercury contained
in parts to the human health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European
Union Member States.
Cautions
(1) Unauthorized reprinting of the contents of this manual is prohibited.
(2) The contents of this manual are subject to change in the future without notice.
(3) The contents of this manual have been prepared with scrupulous care, but please notify NEC
should you have any doubts or notice any mistakes or omissions.
(4) Please note that NEC will accept no responsibility whatsoever for claims for damages, lost earn-
ings, etc., arising from the use of this product, regardless of article (3) above.
(5) NEC will replace any manuals presenting incorrect collation or missing pages.

ENG-2
ENG-3
DOC Compliance Notice (for Canada only)
This Class B digital apparatus complies with Canadian ICES-003.
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit
EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply
with this government regulation could void your right to operate this equipment. This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveriscon-
nected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
U.S.Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Boulevard, Suite 1100
Itasca, Illinois 60143-1248
Tel. No.: [phone]
Type of Product: Interactive White Board Kit
Equipment Classification: Class B Peripheral
Model No.: NP04Wi
We hereby declare that the equipment specified above conforms to the technical
standards as specified in the FCC Rules.

ENG-4
ENG-5
Read This Before Starting
About the pictograms
To ensure safe and proper use of the product, this installation manual uses a number of pictograms to
prevent injury to you and others as well as damage to property.
The pictograms and their meanings are described below. Be sure to understand them thoroughly before
reading this manual.
WARNING
Failing to heed this pictogram and handling the product
erroneously could result in accidents leading to death or
major injury.
CAUTION
Failing to heed this pictogram and handling the product
erroneously could result in personal injury or damage to
surrounding property.
Examples of pictograms
The symbol indicates instructions urging caution (including warnings).
A concrete indication of the caution is given within the symbol.
The symbol indicates prohibited actions.
A concrete indication of the prohibited action is given within the symbol.
The symbol indicates required actions.
A concrete indication of the required action is given within the symbol.
WARNING
• Setupthisproductontheprojectorbeforeinstallingtheprojectorontheceilingorwall.
If this product is set up after installing the projector on the ceiling or wall, the camera
unit may not be fix on properly and it may cause of falling down and resulting in injury
At the same time, it may cause of damage on the camera unit.
• Makesuretofastenthescrewsafterxingonthecameraunit.Ifthescrewsarenot
fastened securely, the camera unit may fall down and result in injury. At the same time,
it may cause of damage on the camera unit.
• Donotholdthecameraunitformovingtheprojectoranddonotapplyexcessiveforceto
the camera unit. It may cause of damage on the camera unit and resulting in injury.
• Donotplacethisproductinthefollowingconditions:
- near water, baths, or damp rooms.
- in direct sunlight, near heaters, or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- in high temperature place
• Donotdissembleorremodelthestyluspen.Donotgiveashocktothestyluspenor
bend it. It may cause of damage on the stylus pen and resulting in injury.

ENG-4
ENG-5
Notes
• Useaatandhardscreenwithascreensizeof100inchesorless.
• Somescreensurfacescanbescratchedbythestyluspentip.Beforeusingthestyluspen,testitin
an inconspicuous part of the screen to be sure the pen tip will not damage the screen surface.
• Donotusethestyluspeninthebelowmentionedareas.
It may cause of malfunction of the stylus pen.
- In the area direct sunlight strikes the screen surface and the camera unit.
- In the area light of halogen or filament lamps directly strikes the screen surface and the camera
unit.
- Inthe case, materialsreectslight isusedwithin thestylus penoperation area.(ex. screen
frame)
• Donotusethestyluspeninthebelowmentionedenvironment.Itmaycauseofmalfunctionofthe
stylus pen.
- When the infrared remote is used.
• Theguaranteedoperationtemperaturerangeforthefunctionofthestyluspenis5°to40°C(41°to
104°F).
• Whenmountingorremovingthecameraunit,donotremoveanyscrewsotherthanthosespeci-
fied.
Disposing of this product
• Whendisposingof thisproduct,contactyourstoreofpurchase orlocalgovernment forinstruc-
tions.
Features
• Interactiveelectronicwhiteboardfunction
By combination with drawing software, the white board or wall can be used as your interactive white
board, and you can take handwritten notes or draw pictures on the screen with the supplied stylus
pen.
Moreover, by combination with the Touch Module (NP01TM sold saparately), it enables to draw on
the white board or wall by your finger.
Supported projectors:
- UM330X, UM280X, UM330W, UM280W
- UM351W, UM301W, UM361X, UM301X
- U321H
* Do not fix on this product other than the above listed supported projectors and the exclusive
holder.
• Oneormorepeoplecantakenotesordrawpictureswithstyluspensatthesametime
Two stylus pens come standard with the product. The stylus pen is also available as an option
(NP02Pi).
Up to 10 stylus pens can be used at the same time on the product.
However, this number will vary depending on drawing software you use.
For using drawing software, refer to the user manual included with the drawing software.
• AutoCalibrationfunction
Position adjustment is easily done thanks to the auto calibration function.

ENG-6
ENG-7
Packaged Items
Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
• Cameraunitx1
• Attachmentx1
(Application model: U321H)
• Gasketx1
(Application model : U321H)
• Holderx1
• Coverx1
The holder and the cover are assembled.
• Styluspenx2
• USBcablex1
For charging the stylus pen
• USBcable(4.5m/14.8feet)x1
For connecting the computer with the
camera unit
• InstallationManual(thisdocument)x1
• Screw(M3)x4
NOTE
• Downloadthedriverandthecalibrationsoftwarefromourwebsitetoinstallthemonthecomputer.
URL: http://www.nec-display.com/dl/en/index.html
• Drawingsoftwareisrequiredtousetheinteractivewhiteboardfunction.
No drawing software is included with the product. Get commercially available drawing software.

ENG-6
ENG-7
Part Names
Camera unit
Stylus pen
USB cable
Computer
Projector
Screen or whiteboard
The drawing shows an example of the optional
wall mount unit (Model name: NP04WK) with the
projector mounted on it.

ENG-8
ENG-9
Part names of the supplied stylus pen
Pen tip
Indicator (LED)
Charging port (USB)
Charging the stylus pen
Use the supplied USB cable for charging the stylus pen to connect the charging port (USB) of the stylus
pen with the USB port of the computer.
The stylus pen will start charging. Charging will complete in about 3 minutes.
• PressingthepentipagainstascreenorwhiteboardwillturntheindicatorLEDtored,whichindicates
that charging is completed and you are ready to use the stylus pen. If the red LED turns off, charge
the stylus pen.
Cautions on using the stylus pen
• Donotdamagethestyluspenbydroppingitontheoorormishandlingit.
• Keepthestyluspenawayfromwaterandotherliquids.Ifthestyluspengetswet,wipethestyluspen
dry immediately.
• Avoidheatandhumidwhenpossible.

ENG-8
ENG-9
Setup Procedure
Setup Flow
1. Connect the USB cable and the holder to the camera unit.
2. Fix the camera unit onto the projector.
* Fixing procedure for U321H is differed from for other models.
3. Mount the cover on the holder.
4. Connect the projector with the computer.
5. Power on the projector and adjust the position and focus for projected im-
age.
6. Connect the USB cable on which terminal has connected with the camera unit
with the computer.
7. Install the driver and the calibration software on the computer and perform the
calibration.
Warning
- Set up this product on the projector before installing the projector on the ceiling or wall. If
this product is set up after installing the projector on the ceiling or wall, the camera unit may
not be fixed properly and it may cause of falling down and resulting in injury. At the same
time, it may cause of damage on the camera unit.
- Make sure to fasten the screws after fixing on the camera unit. If the screws are not fastened
securely, the camera unit may fall down and result in injury. At the same time, it may cause
of damage on the camera unit.
- Do not hold the camera unit for moving the projector and do not apply excessive force to
the camera unit. It may cause of damage on the camera unit and resulting in injury.
Preparation:
- Prepare a plus headed screw driver
- However the holder and the cover has been in engaged condition for shipment, remove the holder
by pressing the button on the cover.
1
2
For fixing on U321H, you need to seal the gasket on
the holder. Peel off the release paper on the rear face
of the gasket, attach it to the arrow pointed position on
the illustration.
align corners

ENG-10
ENG-11
1. Connect the USB cable and the holder to the camera unit.
Connect the USB cable and the holder to the camera unit.
Connect the L-shaped terminal of the supplied USB cable (4.5m/14.8ft) to the USB port (type
B) on the camera unit.
Fix the camera unit on the holder.
Engage two protrusions on the camera unit into the fixing holes on the holder and align the
position of screw holes. Fix the camera unit by one screw.
2. Fix the camera unit onto the projector.
* Fixing procedure for U321H is differed from for other models, UM351W, UM301W, UM361X, UM301X,
UM330X, UM280X, UM330W and UM280W
For UM351W/UM301W/UM361X/UM301X/UM330X/UM280X/UM330W/UM280W
- Remove the cable cover if it is mounted on the projector. Please follow the instructions on the
projector User’s Manual for mounting/demounting the cable cover.
- Require one screw.
Fix the camera unit on the cable cover.
From the external side of the cable cover, engage two protrusions on the holder into the fixing
holes on the cable cover, then align the position of fixing holes.
Fasten these with a screw putting from the inside of the cable cover.
12

ENG-10
ENG-11
Fix the cable cover on the projector.
For U321H
Require three screws and the attachment.
Mount the attachment on the projector.
Put the projector bottom face up and push two protrusions on the attachment in the fixing holes
on the projector, then align the position of the fixing holes. Fasten them by two screws.
Fix the camera unit on the attachment.
Put the projector facing up and engage two protrusions on the holder in the fixing holes on the
holder, then align the position of the fixing holes. Fasten them by one screw.

ENG-12
ENG-13
3. Mount the cover on the holder.
Push in the claws at the bottom of cover to the fixing holes on the holder until click sound is heard.
Put the USB cable inside the cover. For U321H, put the USB cable through the notch as the cable
holder.
UM351W/UM301W/UM361X/UM301X/UM330X/UM280X/ UM330W/UM280W
2
1
U321H
2
1
Cable holder

ENG-12
ENG-13
4. Connect the projector to the computer.
The projector can be connected to a computer using the computer cable (supplied with the projec-
tor) or a commercially available HDMI cable.
5. Turn on the projector power and then adjust the position /
focus of the projected image.
For the adjustment procedure, see the projector user’s manual.
6. Connect the computer and the camera unit with the included
USB cable.
Connect the terminal of the USB cable (4.5 m/14.8 ft) whose another terminal has connected with
the camera unit to the USB port (Type A) on the computer.

ENG-14
ENG-15
UM330X/UM280X/ UM330W/ UM280W/
UM351W/UM301W/UM361X/UM301X
U321H
7. Install the driver and the calibration software on the
computer and perform the calibration
Download the driver and the calibration software from our website and install them on the computer.
URL: http://www.nec-display.com/dl/en/index.html
The The operation manual for installation and calibration is available in PDF (Portable Document
Format).
To view or print the PDF files Adobe Reader™ is required.
If you cannot open a PDF file on your computer, obtain the current version of Adobe Reader for
your OS from the home page of Adobe Systems and install it on your computer.
NOTE
• Drawingsoftwareisrequiredtousetheinteractivewhiteboardfunction.
No drawing software is included with the product. Get commercially available drawing software.

ENG-14
ENG-15
Troubleshooting
Stylus pen does not work.
• IstheUSBcableconnectedbetweenthecomputer(typeAUSBport)andthecameraunit(typeB
USB port)?
• Havethedriverandthecalibrationsoftwarebeeninstalledonyourcomputer?
• Areyouusingthestyluspeninoneofthefollowingenvironment?
- If direct sunlight strikes the screen surface and/or camera unit, change the installation place where
it is not exposed to direct sunlight.
- If light of a halogen and/or a filament lamp strikes the screen surface and/or camera unit, change
the installing direction of the screen and/or camera unit, or block off lamp light.
- Donotuseascreenwhosematerialofframereectslight.
 InuenceofexternallightisdescribedatthetroubleshootingintheNP04Wisoftwareguide.Refer
to the software guide on the support page for our projectors uploaded in our web site and set them
upinanappropriateplacewheredoesnotgetinuenceoflight.
• Isthecameraunitsettothecorrectposition?
• Doesthestyluspenhavepropercharge?
If pressing the pen tip will not turn LED to red, charge the stylus pen.
• Isthescreensizeandusagetemperaturewithinappropriaterange?
Use a screen within the effective range.
Usethestyluspenwithinatemperaturerangeof5°to40°C(41°to104°F).
• Isthelensofthecameraunitsoiled?
 Ifthelensissoiled,wipeitwithasoft,dry,non-uffycloth.
Lines traced with the stylus pen do not match screen.
• Hasthesensorbeenproperlycalibrated?
• Ifperformingthecalibrationautomaticallywillnotresolvetheproblem,trytoperformthecalibration
manually.
Specifications
Camera unit
• Inputterminal:USBTypeB×1
• Powerconsumption:120mA/5V,600mW
• Weight:70g/2.5oz
• Externaldimensions:135(W)x32(H)x36(D)mm/5.3"(W)x1.3"(H)x1.4"(D)(notincludingprotru-
sions)
• Effectiverange:60"to100"
• Operatingtemperatureandhumidity:5°to40°C(41°to104°F)/20%to80%(non-condensing)
• Storagetemperatureandhumidity:−10°to50°C(14°to122°F)/20%to80%(non-condensing)
Stylus pen
• Weight:25g/0.9oz
• Powersupply:Chargingtype(supercapacitor)
• Chargingtime:3minutes
• Estimatednumberofchargingthebattery:100,000
• Operatingtime:about2hours
• Operatingtemperatureandhumidity:5°to40°C(41°to104°F)/20%to80%(non-condensing)
• Storagetemperatureandhumidity:−10°to50°C(14°to122°F)/20%to80%(non-condensing)

GER-1
NP04Wi
Installationshandbuch
Einführung..................................................................................... GER-2
Bitte vor Beginn lesen.................................................................... GER-3
Hinweis ......................................................................................... GER-4
Entsorgung dieses Produkts.......................................................... GER-4
Merkmale ...................................................................................... GER-4
Enthaltene Teile.............................................................................. GER-5
Teilebezeichnungen ....................................................................... GER-6
VerfahrenzurEinrichtung............................................................... GER-8
Fehlerbehebung .......................................................................... GER-14
Technische Daten ........................................................................ GER-14
INHALT
Interaktives Whiteboard-Set

GER-2
GER-3
Einführung
VielenDankfürdenKaufderinteraktivenTafelvonNEC(Modellname:NP04Wi).
Durch Anschluss eines NEC-Projektors an dieses Produkt kann die Tafel oder Wand als Ihre interaktive
Tafel verwendet werden.
Der beiliegende Eingabestift verfügt über einen eingebauten super-Kondensator-Ladespeicher. Laden Sie
den super-Kondensator für 3 Minuten auf, bevor Sie den Eingabestift zum ersten Mal verwenden.
IndiesemHandbuchwirdalsBeispieleineVerbindungmitdemUM351Wverwendet.
Die Begriffe HDMI und HDMI High-Definition Multimedia Interface sowie das HDMI-Logo sind Waren-
zeichen oder eingetragene Warenzeichen der HDMI Licensing LLC in den Vereinigten Staaten und
anderen Ländern.
Entsorgung Ihres benutzten Gerätes
Die EU-weite Gesetzgebung, wie sie in jedem einzelnen Mitgliedstaat gilt, bestimmt, dass
benutzte elektrische und elektronische Geräte mit dieser Markierung (links) getrennt vom
normalen Haushaltsabfall entsorgt werden müssen.
Folgen Sie beim Entsorgen eines solchen Gerätes bitte den Anweisungen Ihrer örtlichen Be-
hörde und/oder konsultieren Sie den Händler, bei dem Sie das Gerät erworben haben.
Nach der Sammlung benutzter Geräte werden diese erneut verwendet und entsprechend
den Umweltbestimmungen recycelt. Das trägt dazu bei, die Abfallmenge zu reduzieren
sowie die negativen Auswirkungen beispielsweise von in Teilen des Geräts enthaltenem
Quecksilber auf die Gesundheit und die Umwelt möglichst gering zu halten.
Die Markierung auf elektrischen und elektronischen Geräten gilt nur für die gegenwärtigen
Mitgliedstaaten der Europäischen Union.
Vorsichtsmaßnahmen
(1) EineunerlaubteVervielfältigungdesInhaltsdiesesHandbuchsistuntersagt.
(2) Der Inhalt dieses Handbuchs kann ohne Ankündigung geändert werden.
(3) Der Inhalt dieses Handbuchs wurde mit großer Sorgfalt zusammengestellt. Informieren Sie jedoch
bitte NEC, sollten Sie Zweifel haben oder Fehler oder Auslassungen bemerken.
(4) BittebeachtenSie,dassNECkeineVerantwortungfürSchäden,Umsatzverlusteusw.übernimmt,
dieaufgrundderVerwendungdiesesProduktsentstehen,unabhängigvonArtikel(3)oben.
(5) NEC wird alle Handbücher ersetzen, die eine fehlerhafte Kollation oder fehlende Seiten aufwei-
sen.