NEC SX-Aurora TSUBASA A100-1 User manual

SX-Aurora TSUBASA
A100-1
USER’S GUIDE
Revision 1.0b

2
The information in this User’s Guide has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this Guide, or to notify any person or organization of the updates.
Please Note: For the most up-to-date version of this Guide, please see our website at
http://www.nec.com/en/global/prod/hpc/aurora/document/ .
NEC Corporation. ("NEC") reserves the right to make changes to the product described in this Guide at any time and
without notice. This product, including software and documentation, is the property of NEC and/ or its licensors, and is
supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted
by the terms of said license.
IN NO EVENT WILL NEC CORPORATION. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVEORCONSEQUENTIALDAMAGESARISINGFROMTHEUSEORINABILITYTOUSETHISPRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, NEC
CORPORATION. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR
USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
The products sold by NEC are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical
systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, NEC disclaims any and all liability, and should buyer use or sell such products for use
in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify,
defend and hold NEC harmless for and against any and all claims, demands, actions, litigation, and proceedings of
any kind arising out of or related to such ultra-hazardous use or sale.
Guide Revision 1.0
Release Date: Feb. 28, 2018
Unless you request and receive written permission from NEC Corporation., you may not copy any part of this
document. Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.

3
SX-Aurora TSUBASA A100-1 User's Guide
Preface
About this guide
This Guide is written for professional system integrators and PC technicians. It provides
information for the installation and use of the SX-Aurora TSUBASA A100-1. Installation and
maintenance should be performed by experienced technicians only.
Please refer to the A100-1 server specifications page on our website for updates on supported
memory, processors and operating systems (http://www.nec.com/en/global/prod/hpc/aurora/document/).
Notes
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s Guide for your server.
• NEC product manuals: http://www.nec.com/en/global/prod/hpc/aurora/document/
• Product safety info:
http://www.nec.com/en/global/prod/hpc/aurora/document/safety_information.pdf
This Guide may be periodically updated without notice. Please check the NEC website for
possible updates to the manual revision level.
Warnings
Special attention should be given to the following symbols used in this guide.
Warning! Indicates important information given to prevent equipment/property damage
or personal injury.
Warning! Indicates high voltage may be encountered when performing a procedure.

4
Preface
Table of Contents
Chapter 1 Introduction
1.1 Overview.............................................................................................................................5
1.2 Unpacking the System........................................................................................................5
1.3 System Features.................................................................................................................6
1.4 Server Chassis Features....................................................................................................7
Control Panel.....................................................................................................................7
Front Features...................................................................................................................8
Rear Features....................................................................................................................9
1.5 System Block Diagram......................................................................................................10
1.6 Ports.................................................................................................................................11
1.7 LED...................................................................................................................................13
Chapter 2 Workstation Setup
2.1 Overview...........................................................................................................................14
2.2 Preparing for Setup...........................................................................................................14
Choosing a Setup Location .............................................................................................14
General Precautions........................................................................................................14
Chapter 3 Maintenance and BIOS Setting
3.1 Overview...........................................................................................................................15
Appendix A BIOS Codes
Appendix B Standardized Warning Statements for AC Systems

5
SX-Aurora TSUBASA A100-1 User's Guide
Chapter 1
Introduction
1.1 Overview
This chapter provides a brief outline of the functions and features of SX-Aurora TSUBASA
A100-1.
1.2 Unpacking the System
Inspect the box the SX-Aurora TSUBASA A100-1 was shipped in and note if it was damaged
in any way. If any equipment appears damaged, please file a damage claim with the carrier
who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be situated in
a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and
electromagnetic fields are generated. It will also require a grounded AC power outlet nearby.
Be sure to read the precautions and considerations noted in Appendix B.

6
Chapter 1: Introduction
1.3 System Features
The following table provides you with an overview of the main features of the A100-1.
System Features
Motherboard
Supermirco X11DAi-N
Chassis
Supermicro SC732D3-1200B
CPU
Supports single Intel Xeon 6126/4108 (Socket P0-LGA3647) processor
Socket Type
Socket P0-LGA3647
Memory
96GB
Chipset
PCH C621
PCIe Card
Single Vector Engine 1.0 card
Hard Drives
One 3.5" hard drive
Power
Single 1200W power supply
Form Factor
Mid-tower
Dimensions
(WxHxD) 7.6 x 16.7 x 20.68 in. (193 x 424 x 525.3 mm)
Host Server
A100-1-VH

7
SX-Aurora TSUBASA A100-1 User's Guide
1.4 Server Chassis Features
Control Panel
The switches and LEDs located on the control panel are described below. See Chapter 4 for more details
on the control panel.
2
3 5
4
6
1 7
Figure 1-1. Control Panel View
Control Panel Features
Item
Feature
Description
1
USB 3.0 Ports
Front access USB 3.0 ports (2x)
2
NIC LED
Indicates network activity on the LAN port when flashing.
3
HDD LED
Indicates activity on the hard drive when flashing.
4
Information LED
See table below
5
Power Button
The main power button is used to apply or remove power from the power supply
to the server. Turning off system power with this button removes the main power
but maintains standby power. To perform many maintenance tasks, you must
also unplug system before servicing
6
Line Out
Line out jack
7
Mic
Microphone jack
Information LED
Status
Description
Continuously on and red
An overheat condition has occured.
(This may be caused by cable congestion.)
Blinking red (1Hz)
Fan failure, check for an inoperative fan.
Solid blue
Local UID has been activated. Use this function to
locate the server in a rackmount environment.
Blinking blue
Remote UID is on. Use this function to identify the
server from a remote location.

8
1
2
3
Chapter 1: Introduction
Front Features
A100-1 mid-tower chassis is a Supermicro SC732D3-1200B chassis. See the illustration
below for the features included on the front of the chassis.
Figure 1-2. Chassis Front View
Front Chassis Features
Item
Feature
Description
1
Fixed Drive Area
Supports two fixed 5.25" drives (such as a DVD-ROM)
2
Control Panel
Front control panel (see preceding page)
3
Internal HDD Cage (behind
bezel)
Supports four 3.5" hard drives in a rotatable cage

9
SX-Aurora TSUBASA A100-1 User's Guide
Rear Features
The illustration below shows the features included on the rear of the chassis.
1
2
3
Figure 1-3. Chassis Rear View
Rear Chassis Features
Item
Feature
Description
1
Power Supply
1200W power supply
2
I/O Backpanel
Rear I/O ports (see Section 1.6)
3
PCI Slots
Supports seven full-height, full-length PCI expansion cards

10
Chapter 1: Introduction
1.5 System Block Diagram
Figure 1-4. C621 Chipset: System Block Diagram
Note: This is a general block diagram and may not exactly represent the features on your
motherboard. See the Section 1.3 System Features for the actual specifications of your
motherboard.

11
SX-Aurora TSUBASA A100-1 User's Guide
1.6 Ports
Rear I/O Ports
See the figure below for the locations and descriptions of the various I/O ports on the rear
of the motherboard.
1 6 7 9
Figure 1-5. Rear I/O Ports
Rear I/O Ports
#
Description
#
Description
1.
VGA
6.
7.1 HD Audio
2.
USB 1 (USB 3.0)
7.
LAN1
3.
USB 2 (USB 3.0)
8.
LAN2
4.
USB 3 (USB 3.0)
9.
USB 8 (USB 3.1) type C
5.
USB 4 (USB 3.0)
10.
USB 9 (USB 3.1) type A
Ethernet Ports
Two Ethernet ports (LAN1, LAN2) are located on the I/O backplane. These Ethernet ports
support 1 GbE LAN connections on the X11DAi-N. These Ethernet ports accept RJ45 type
cables. Please refer to the LED Indicator section for LAN LED information.
Notes:
- LAN interface link speed supports only 1Gb/s.
Please connect the LAN interface to 1Gb/s supported Ethernet switch.
- In case link-up fails, please turn off auto-negotiation mode and fix the link-speed to 1Gb/s on
Ethernet switch.
VGA Port
The onboard VGA port is located next to USB 3.0 ports on the I/O back panel. Use this
connection for VGA display.
5
4
3
2
8
10

12
7.1 HD Audio
#
Definition
1
SPDIF_Out
2
Surround_Out
3
CEN/LFE_Out
4
Mic_In
5
Line_Out
6
Line_In
10-Pin Audio
Pin Definitions
#
Definition
1
Microphone_Left
2
Audio_Ground
3
Microphone_Right
4
Audio_Detect
5
Line_2_Right
6
Ground
7
Jack_Detect
8
Key
9
Line_2_Left
10
Ground
Chapter 1: Introduction
7.1 HD (High-Definition) Audio
This motherboard features a 7.1 Channel High-Definition Audio (HDA) codec that provides 8
DAC channels. The HD audio supports multiple-streaming 7.1 sound playback through the
front_panel stereo output via the subwoofer speakers. Download the appropriate software
from our website to enable this function.
Figure 1-6. Audio Pin
Universal Serial Bus (USB) Ports
There are four USB 3.0 ports (USB 1-4) and two USB 3.1 ports (USB 8/9) on the I/O back
panel. Another USB 3.0 header, located next to the TPM/Port 80 header, also provides two
USB 3.0 connections (USB 5/6) for front access. In addition, a Type A USB connector (USB
7) can be used for front side USB 3.0 access with a cable (not included).
3
2
1
6
5
4
Front Panel USB 5/6 (3.0)
Pin Definitions
Pin#
Definition
Pin#
Definition
1
VBUS
19
Power
2
Stda_SSRX-
18
USB3_RN
3
Stda_SSRX+
17
USB3_RP
4
GND
16
GND
5
Stda_SSTX-
15
USB3_TN
6
Stda_SSTX+
14
USB3_TP
7
GND
13
GND
8
D-
12
USB_N
9
D+
11
USB_P
10
x
Back Panel USB 1-4 (3.0)
Pin Definitions
Pin#
Definition
Pin#
Definition
A1
VBUS
B1
Power
A2
D-
B2
USB_N
A3
D+
B3
USB_P
A4
GND
B4
GND
A5
Stda_SSRX-
B5
USB3_RN
A6
Stda_SSRX+
B6
USB3_RP
A7
GND
B7
GND
A8
Stda_SSTX-
B8
USB3_TN
A9
Stda_SSTX+
B9
USB3_TP
Type A USB 7 (3.0)
Pin Definitions
Pin#
Definition
Pin#
Definition
1
VBUS
5
SSRX-
2
USB_N
6
SSRX+
3
USB_P
7
GND
4
Ground
8
SSTX-
9
SSTX+

13
SX-Aurora TSUBASA A100-1 User's Guide
1.7 LED Indicators
LAN LEDs
The LAN ports are located on the I/O
Backplane on the motherboard. Each
Ethernet LAN port has two LEDs. The
yellow LED on the right side of the LAN
port indicates activity. The Link LED located
on the left may be green, amber or off to
indicate the speed of the connection. See
the table at right for more information.
Notes:
- LAN interface link speed supports only 1Gb/s.
Please connect the LAN interface to 1Gb/s supported Ethernet switch.
- In case link-up fails, please turn off auto-negotiation mode and fix the link-speed to 1Gb/s on
Ethernet switch.
LAN1/2 LED
(Connection Speed Indicator)
LED Color
Definition
Off
No Connection, 100 Mb/s or 10 Mb/s
Amber
1 Gb/s

14
Chapter 2: Workstation Setup
Chapter 2
Workstation Setup
2.1 Overview
This chapter provides advice setting up your system.
2.2 Preparing for Setup
Please read this section in its entirety before you begin the installation.
Choosing a Setup Location
• The system should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated.
• This product should be installed only in a RestrictedAccess Location (dedicated equipment
rooms, service closets, etc.).
General Precautions
• Review the electrical and general safety precautions in Appendix B.
• Use a regulating uninterruptible power supply (UPS) to protect the server from power
surges and voltage spikes and to keep your system operating in case of a power failure.
• Allow any drives and power supply modules to cool before touching them.

15
SX-Aurora TSUBASA A100-1 User's Guide
Chapter 3
Maintenance and BIOS Setting
3.1 OverView
About maintenance and BIOS setting, only trained and qualified personnel of NEC system
should be allowed to install, replace, or service this equipment.

16
Appendix A: BIOS Codes
Appendix A
BIOS Codes
A.1 BIOS Error POST (Beep) Codes
During the POST (Power-On Self-Test) routines, which are performed each time the system
is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the boot-up
process. The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up procedure. If
a fatal error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps. The numbers
on the fatal error list (on the following page) correspond to the number of beeps for the
corresponding error. All errors listed, with the exception of Beep Code 8, are fatal errors.
BIOS Beep (POST) Codes
Beep Code
Error Message
Description
1 beep
Refresh
Circuits have been reset (Ready to power up)
5 short, 1 long
Memory error
No memory detected in system
5 long, 2 short
Display memory read/write error
Video adapter missing or with faulty memory
1 long continuous
System OH
System overheat condition

17
SX-Aurora TSUBASA A100-1 User's Manual
Appendix B
Standardized Warning Statements for AC
Systems
B.1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of
situations which have the potential for bodily injury. Should you have questions or experience
difficulty, contact NEC's Technical Support department for assistance. Only certified
technicians should attempt to install or configure components.
Read this appendix in its entirety before installing or configuring components in the NEC
chassis.
These warnings may also be found on our website at
http://www.nec.com/en/global/prod/hpc/aurora/document/safety_information.pdf
Warning Definition
Warning! This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards involved
with electrical circuitry and be familiar with standard practices for preventingaccidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、電気
回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen
führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer
Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen
Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen
Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät
ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.

18
Appendix B: Standardized Warning Statements for AC Systems
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement,
soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les
procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance
des traductions des avertissements figurant dans les consignes de sécurité traduites qui
accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque
avertissement.
CONSERVEZ CES INFORMATIONS.
Circuit Breaker
Warning! This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw.
Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung
nicht mehr als: 250 V, 20 A beträgt.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de
l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection
n'est pas supérieur à :250 V, 20 A.

19
SX-Aurora TSUBASA A100-1 User's Manual
Equipment Installation
Warning! Only trained and qualified personnel should be allowed to install, replace,
or service this equipment.
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可されています。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de
ces équipements à des personnels qualifiés et expérimentés.
Restricted Area
Warning! This unit is intended for installation in restricted access areas. A restricted
access area can be accessed only through the use of a special tool, lock and key, or
other means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いてのみ出入りが可能で
す。
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt
zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer
sonstigen Sicherheitsvorkehrung möglich.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone d'accès
réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une
clé, ou tout autre moyen de sécurité.

20
Appendix B: Standardized Warning Statements for AC Systems
Comply with Local and National Electrical Codes
Warning! Installation of the equipment must comply with local and national electrical
codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
Attention
L'équipement doit être installé conformément aux normes électriques nationales et locales.
Product Disposal
Warning! Ultimate disposal of this product should be handled according to all national
laws and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要があります。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou
directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.