NETGEAR WG602 - 54 Mbps Wireless Access Point User manual

202-10060-02, February 2005
202-10060-02
February 2005
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Phone 1-888-NETGEAR
Reference Manual for the
NETGEAR 54 Mbps Wireless
Access Point WG602v3

ii
202-10060-02, February 2005
NETGEAR, INC.
Technical Support
Please register to obtain technical support. Please retain your proof of purchase and warranty
information.
To register your product, get product support or obtain product information and product
documentation, go to www.netgear.com. If you do not have access to the World Wide Web, you can
register your product by filling out the registration card and mailing it to NETGEAR customer
service.
You will find technical support information at:
www.netgear.com/support/main.asp through the customer service area. If you want to contact
technical support by telephone, see the support information card for the correct telephone number
for your country.
© 2005 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a registered trademark of NETGEAR, INC. Windows is a registered trademark of Microsoft
Corporation. Other brand and product names are trademarks or registered trademarks of their respective
holders. Information is subject to change without notice. All rights reserved.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the
right to make changes to the products described in this document without notice. NETGEAR does not
assume any liability that may occur due to the use or application of the product(s) or circuit layout(s)
described herein.

202-10060-02, February 2005
iii
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements
WARNING! To ensure compliance with FCC RF exposure requirements, the antenna used for this device
must be installed to provide a separation distance of at least 20 cm (8 in) from all persons and must not be
co-located or operating in conjunction with any other antenna or radio transmitter. Installers and end-users
must follow the installation instructions provided in this user guide.
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
Warning!
To comply with the FCC’s
exposure requirements you must
maintain a distance of at least 1
cm from the antenna of this
device while it is in use. This
device should not be co-located
with other transmitters.
NETGEAR NETGEAR WG602v3 54 Mbps Wireless

202-10060-02, February 2005
iv
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 2.4 GHz frequency range. FCC requires this
product to be used indoors in 2.4 GHz the frequency range to reduce the potential for harmful interference to
co-channel Mobile Satellite systems.
Regulatory Compliance Information
This device is restricted to indoor use due to reduce the potential for harmful interference to co-channel
Mobile Satellite and Radar Systems.
Canadian Department of Communications Compliance Statement
This Class B Digital apparatus (NETGEAR WG602v3 54 Mbps Wireless Access Point) meets all
the requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareil numerique del la classe B respect les exigences du Regalement sur le material broilleur du
Canada.
This device comples with Class B limits of Industry of Canada. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
The device is certified to the requirements of RSS-139-1 and RSS-210 for 2.4 GHz spread spectrum devices.
The use of this device in a system operating either partially or completely outdoors may require the user to
obtain a license for the system according to the Canadian regulations. For further information, contact your
local Industry Canada office.
Product and Publication Details
Model Number: WG602v3
Publication Date: February 2005
Product Family: wireless access point
Product Name: NETGEAR WG602v3 54 Mbps Wireless Access Point
Home or Business Product: Business
Language: English
Publication Part Number: 202-10060-02

Contents iii
202-10060-02, February 2005
Contents
Chapter 1
About This Manual
Audience, Scope, Conventions, and Formats ................................................................1-1
How to Use This Manual ................................................................................................1-2
How to Print this Manual .................................................................................................1-3
Chapter 2
Introduction
About the NETGEAR WG602v3 54 Mbps Wireless Access Point .................................2-1
Support for Standards ..............................................................................................2-1
Key Features ............................................................................................................2-2
802.11g Standards-based Wireless Networking ......................................................2-2
Autosensing Ethernet Connections with Auto Uplink ...............................................2-3
Wireless Multimedia (WMM) Support .......................................................................2-3
Compatible and Related NETGEAR Products .........................................................2-3
System Requirements ....................................................................................................2-4
What’s In the Box? .........................................................................................................2-4
Hardware Description .....................................................................................................2-5
WG602v3 Wireless Access Point Front Panel .........................................................2-5
WG602v3 Wireless Access Point Rear Panel ..........................................................2-6
Power Socket ....................................................................................................2-6
Reset and Restore to Factory Defaults Button ..................................................2-6
RJ-45 Ethernet Port ...........................................................................................2-6
Detachable Antenna ..........................................................................................2-6
Chapter 3
Basic Installation and Configuration
Observing Placement and Range Guidelines .................................................................3-1
Default Factory Settings .................................................................................................3-2
Understanding WG602v3 Wireless Security Options .....................................................3-3
Installing the NETGEAR WG602v3 54 Mbps Wireless Access Point .............................3-4
Two Ways to Log In to the WG602v3 .............................................................................3-6
How to Log in Using the Default IP Address of the WG602v3 .................................3-7

202-10060-02, February 2005
iv Contents
How to Log In to the WG602v3 Using Its Default NetBIOS Name ...........................3-9
Using the Basic IP Settings Options .............................................................................3-10
Understanding the Basic Wireless Settings ..................................................................3-11
Understanding Wireless Security Options ....................................................................3-13
Information to Gather Before Changing Basic Wireless Settings ...........................3-15
How to Configure WEP Wireless Security ....................................................................3-16
How to Configure WPA-PSK Wireless Security ............................................................3-17
How to Configure WPA2-PSK Wireless Security ..........................................................3-18
How to Configure WPA-PSK/WPA2-PSK Wireless Security ........................................3-19
How to Restrict Wireless Access by MAC Address ......................................................3-20
Chapter 4
Management
Viewing General Information ..........................................................................................4-1
Viewing a List of Attached Devices .................................................................................4-3
Upgrading the Wireless Access Point Software .............................................................4-3
Rebooting and Resetting Factory Default Options .........................................................4-5
Restoring the WG602v3 to the Factory Default Settings .........................................4-5
Using the Reset Button to Reboot or Restore Factory Defaults ...............................4-5
Changing the Administrator Password ...........................................................................4-6
Chapter 5
Advanced Configuration
Understanding Advanced Wireless Settings ..................................................................5-1
Configuring Wireless Distribution System Links .............................................................5-2
How to Configure Wireless Bridge Links ..................................................................5-2
How to Configure a WG602v3 as a Point-to-Point Bridge .......................................5-4
How to Configure Wireless Multi-Point Bridging ......................................................5-5
How to Configure Wireless Repeating .....................................................................5-6
Chapter 6
Troubleshooting
Troubleshooting ..............................................................................................................6-1
No lights are lit on the access point. ........................................................................6-1
The Ethernet LAN light is not lit. ..............................................................................6-1
The Wireless LAN activity light is not lit. .................................................................6-2
I cannot configure the wireless access point from a browser. .................................6-2
I cannot access the Internet or the LAN with a wireless capable computer. ...........6-2

Contents v
202-10060-02, February 2005
When I enter a URL or IP address I get a timeout error. ..........................................6-3
Using the Reset Button to Restore Factory Default Settings ..........................................6-3
Appendix A
Specifications
Specifications for the WG602v3 .................................................................................... A-1
Appendix B
Wireless Networking Basics
Wireless Networking Overview ...................................................................................... B-1
Infrastructure Mode ................................................................................................. B-1
Ad Hoc Mode (Peer-to-Peer Workgroup) ................................................................ B-2
Network Name: Extended Service Set Identification (ESSID) ................................ B-2
Authentication and WEP Data Encryption ..................................................................... B-2
802.11 Authentication .............................................................................................. B-3
Open System Authentication ................................................................................... B-3
Shared Key Authentication ...................................................................................... B-4
Overview of WEP Parameters ................................................................................ B-5
Key Size .................................................................................................................. B-6
WEP Configuration Options .................................................................................... B-7
Wireless Channels ......................................................................................................... B-7
WPA and WPA2 Wireless Security ................................................................................ B-8
How Does WPA Compare to WEP? ........................................................................ B-9
How Does WPA Compare to WPA2 (IEEE 802.11i)? ............................................ B-10
What are the Key Features of WPA and WPA2 Security? .................................... B-10
WPA/WPA2 Authentication: Enterprise-level User
Authentication via 802.1x/EAP and RADIUS .................................................. B-12
WPA/WPA2 Data Encryption Key Management ............................................. B-14
Is WPA/WPA2 Perfect? ......................................................................................... B-16
Product Support for WPA/WPA2 ........................................................................... B-16
Supporting a Mixture of WPA, WPA2, and WEP Wireless Clients is Discouraged B-16
Changes to Wireless Access Points ............................................................... B-17
Changes to Wireless Network Adapters ......................................................... B-17
Changes to Wireless Client Programs ............................................................ B-18
Appendix C
Network, Routing, Firewall, and Cabling Basics
Basic Router Concepts .................................................................................................. B-1
What is a Router? ................................................................................................... B-1

202-10060-02, February 2005
vi Contents
IP Addresses and the Internet ....................................................................................... B-2
Netmask .................................................................................................................. B-4
Subnet Addressing .................................................................................................. B-4
Private IP Addresses ............................................................................................... B-7
Single IP Address Operation Using NAT ................................................................. B-7
IP Configuration by DHCP ...................................................................................... B-8
Domain Name Server .............................................................................................. B-9
Routing Protocols .................................................................................................... B-9
RIP .................................................................................................................... B-9
MAC Addresses and ARP .............................................................................. B-10
Internet Security and Firewalls .................................................................................... B-10
What is a Firewall? .................................................................................................B-11
Stateful Packet Inspection ......................................................................................B-11
Denial of Service Attack .........................................................................................B-11
Ethernet Cabling ...........................................................................................................B-11
Category 5 Cable Quality ...................................................................................... B-12
Inside Twisted Pair Cables .................................................................................... B-13
Uplink Switches, Crossover Cables, and MDI/MDIX Switching ............................ B-14
Appendix D
Preparing Your PCs for Network Access
Preparing Your Computers for TCP/IP Networking .......................................................C-1
Configuring Windows 98 and Me for TCP/IP Networking ..............................................C-2
Installing or Verifying Windows Networking Components .......................................C-2
Enabling DHCP to Automatically Configure TCP/IP Settings ........................................C-3
DHCP Configuration of TCP/IP in Windows 98 and Me ..........................................C-4
Selecting the Windows Internet Access Method .....................................................C-5
Verifying TCP/IP Properties for Windows 98 or Me ................................................C-5
Configuring Windows 2000 or XP for TCP/IP Networking .............................................C-6
Installing or Verifying Windows Networking Components .......................................C-6
DHCP Configuration of TCP/IP in Windows XP ......................................................C-7
DHCP Configuration of TCP/IP in Windows 2000 ..................................................C-9
Verifying TCP/IP Properties for Windows XP or 2000 ........................................... C-11
Glossary

About This Manual 1-1
202-10060-02, February 2005
Chapter 1
About This Manual
This chapter describes the intended audience, scope, conventions, and formats of this manual.
Audience, Scope, Conventions, and Formats
This reference manual assumes that the reader has basic to intermediate computer and Internet
skills. However, basic computer network, Internet, firewall, and VPN technologies tutorial
information is provided in the Appendices and on the Netgear website.
This guide uses the following typographical conventions:
This guide uses the following formats to highlight special messages:
This manual is written for the WG602v3 Access Point according to these specifications:
Table 1-1. Typographical Conventions
italics Emphasis, books, CDs, URL names
bold User input
fixed Screen text, file and server names, extensions, commands, IP addresses
Note: This format is used to highlight information of importance or special interest.
Table 1-2. Manual Scope
Product Version NETGEAR WG602v3 54 Mbps Wireless Access Point
Manual Publication Date February 2005
Note: Product updates are available on the NETGEAR, Inc. Web site at
http://kbserver.netgear.com/products/WG602v3.asp.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
1-2 About This Manual
202-10060-02, February 2005
How to Use This Manual
The HTML version of this manual includes the following:
• Buttons, and , for browsing forwards or backwards through the manual one page
at a time
• A button that displays the table of contents and an button. Double-click on a
link in the table of contents or index to navigate directly to where the topic is described in the
manual.
• A button to access the full NETGEAR, Inc. online knowledge base for the
product model.
• Links to PDF versions of the full manual and individual chapters.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
About This Manual 1-3
202-10060-02, February 2005
How to Print this Manual
To print this manual you can choose one of the following several options, according to your needs.
•Printing a Page in the HTML View.
Each page in the HTML version of the manual is dedicated to a major topic. Use the Print
button on the browser toolbar to print the page contents.
•Printing a Chapter.
Use the PDF of This Chapter link at the top left of any page.
– Click the PDF of This Chapter link at the top right of any page in the chapter you want to
print. The PDF version of the chapter you were viewing opens in a browser window.
Note: Your computer must have the free Adobe Acrobat reader installed in order to view
and print PDF files. The Acrobat reader is available on the Adobe Web site at
http://www.adobe.com.
– Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.
•Printing the Full Manual.
Use the Complete PDF Manual link at the top left of any page.
– Click the Complete PDF Manual link at the top left of any page in the manual. The PDF
version of the complete manual opens in a browser window.
– Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
1-4 About This Manual
202-10060-02, February 2005

Introduction 2-1
202-10060-02, February 2005
Chapter 2
Introduction
This chapter introduces the NETGEAR NETGEAR WG602v3 54 Mbps Wireless Access Point.
Minimal prerequisites for installation are presented in “System Requirements” on page 2-4.
About the NETGEAR WG602v3 54 Mbps Wireless Access
Point
The NETGEAR WG602v3 54 Mbps Wireless Access Point is the basic building block of a
wireless LAN infrastructure. It provides connectivity between wired Ethernet networks and
radio-equipped wireless notebook systems, desktop systems, print servers, and other devices.
The WG602v3 provides wireless connectivity to multiple wireless network devices within a fixed
range or area of coverage, interacting with a wireless network interface card (NIC) via an antenna.
Typically, an in-doors access point provides a maximum connectivity area with about a 300 foot
radius. The NETGEAR WG602v3 54 Mbps Wireless Access Point can support a small group of
users in a range of several hundred feet. Most access points are rated for up to 32 users
simultaneously.
The auto-sensing capability of the NETGEAR WG602v3 54 Mbps Wireless Access Point allows
packet transmission at up to 54 Mbps, or at reduced speeds to compensate for distance or
electromagnetic noise interference.
Support for Standards
The following standards and conventions are supported:
•Standards Compliant.The WG602v3 Access Point complies with the IEEE 802.11g (DSSS).
•WEP support. Support for WEP is included. Both 64-bit and 128-bit keys are supported.
•WPA-PSK support. Support for Wi-Fi Protected Access (WPA) data encryption which
provides strong data encryption and authentication based on a pre-shared key.
•WPA2-PSK support. Support for Wi-Fi Protected Access (WPA2) data encryption which
provides strong data encryption and authentication based on a pre-shared key.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
2-2 Introduction
202-10060-02, February 2005
•Dynamic WEP key Support.Fixed or Dynamic WEP (Wired Equivalent Privacy) keys can
be used.
•DHCP Client Support. DHCP provides a dynamic IP address to PCs and other devices upon
request. The WG602v3 can act as a client and obtain information from your DHCP server.
•NetBIOS & WINS Support. Support for both NetBIOS broadcast and WINS (Windows
Internet Naming Service) allows the WG602v3 to easily fit into your existing Windows
network.
Key Features
The WG602v3 provides solid functionality, including these features:
•Wireless Access Point. Operates as a standard 802.11g access point.
•Wireless Distribution System. Provides wireless bridging – operates as a point-to-point or
multi-point wireless bridge.
•Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily,
using only your Web browser, and can be upgraded remotely.
•Access Control. The Access Control MAC Address filtering feature can ensure that only
trusted wireless stations can use the WG602v3 to gain access to your LAN.
•Simple Configuration. If the default settings are unsuitable, they are easy to change.
•Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct
SSID can connect.
•Autosensing Ethernet Connection with Auto Uplink Interface. Connects to 10/100 Mbps
IEEE 802.3 Ethernet networks.
•LED Indicators. Power and wireless activity are easily identified.
802.11g Standards-based Wireless Networking
The NETGEAR WG602v3 54 Mbps Wireless Access Point provides a bridge between Ethernet
wired LANs and 802.11g compatible wireless LAN networks. It provides connectivity between
Ethernet wired networks and radio-equipped wireless notebook systems, desktop systems, print
servers, and other devices. Additionally, the WG602v3 supports the following wireless features:
• Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure,
retransmission of unacknowledged frames)
• RTS/CTS handshake
• Beacon generation

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
Introduction 2-3
202-10060-02, February 2005
• Packet fragmentation and reassembly
• Authentication Algorithms (Open System, Shared Key, WPA-PSK)
• Short or long preamble
• Roaming among access points on the same subnet
Autosensing Ethernet Connections with Auto Uplink
The WG602v3 can connect to a standard Ethernet network. The LAN interface is autosensing and
capable of full-duplex or half-duplex operation. The wireless access point incorporates Auto
UplinkTM technology. The Ethernet port will automatically sense whether the Ethernet cable
plugged into the port should have a ‘normal’ connection such as to a PC or an ‘uplink’ connection
such as to a switch or hub. That port will then configure itself to the correct configuration. This
feature also eliminates any concerns about crossover cables, as Auto Uplink will accommodate
either type of cable to make the right connection.
Wireless Multimedia (WMM) Support
WMM (Wireless Multimedia) is a subset of the 802.11e standard. WMM allows wireless traffic to
have a range of priorities, depending on the kind of data. Time-dependent information, like video
or audio, will have a higher priority than normal traffic. For WMM to function correctly, Wireless
clients must also support WMM.
Compatible and Related NETGEAR Products
For a list of compatible products from other manufacturers, see the Wireless Ethernet
Compatibility Alliance Web site (WECA, see http://www.wi-fi.net).
The following NETGEAR products work with the WG602v3 Access Point:
• MA701 802.11b 11 Mbps Compact Flash Card
• WAG311 ProSafe 108 Mbps Dual Band PCI Card
• WAG511 ProSafe 108 Mbps Dual Band PC Card
• WGE101 802.11g Wireless Bridge
• WG311 802.11g Wireless PCI Adapter
• WG311T 802.11g 108 Mbps Wireless PCI Card
• WG511 802.11g 54 Mbps Wireless CardBus Adapter
• WG511T 802.11g 108 Mbps Wireless CardBus Adapter

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
2-4 Introduction
202-10060-02, February 2005
System Requirements
Before installing the WG602v3, make sure your network meets these requirements:
• A hub, switch, or Cable/DSL router with an available 10/100 Mbps Ethernet port
• A Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the
package, or one like it
• A 100-240 V, 50-60 HZ AC power source
• A Web browser for configuration such as Microsoft Internet Explorer 5.0 or above, or
Netscape Navigator 4.78 or above
• At least one Pentium class computer (or equivalent) with the TCP/IP protocol installed
• Other 802.11b or 802.11g-compliant devices
What’s In the Box?
The product package should contain the following items:
• NETGEAR WG602v3 54 Mbps Wireless Access Point
• Power adapter and cord (12Vdc, 1.2A)
• Straight through Category 5 Ethernet cable—10 feet (3.04 m)
• Printed WG602v3 54 Mbps Wireless Access Point Installation Guide
•Resource CD for the NETGEAR 54 Mbps Wireless Access Point WG602v3
– Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
(202-10060-02)—this manual
– Windows TCP/IP and Networking Tutorials
– Animated Install Assistant
– Soft copy of the WG602v3 54 Mbps Wireless Access Point Installation Guide
• Support Information card
• Warranty and Registration card
Contact your reseller or customer support in your area if there are any wrong, missing, or damaged
parts. You can refer to the Support Information Card for the telephone number of customer support
in your area. You should keep the Support Information card, along with the original packing
materials, and use the packing materials to repack the WG602v3 if you need to return it for repair.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
Introduction 2-5
202-10060-02, February 2005
To qualify for product updates and product warranty registrations, we encourage you to register on
the NETGEAR Web site at: http://www.netgear.com.
Hardware Description
The NETGEAR WG602v3 54 Mbps Wireless Access Point front and rear hardware functions are
described below.
WG602v3 Wireless Access Point Front Panel
The WG602v3 Access Point provides three status LEDs.
Figure 2-1: WG602v3 front panel
The following table explains the LED indicators:
LED DESCRIPTION
Power
Off
On
Power Indicator
No power. If this LED does not come on with the power adapter and cord correctly
installed, see Chapter 6, “Troubleshooting.”
Power is on.
Ethernet Ethernet LAN Link Activity Indicator
Off
Green On Indicates no Ethernet link detected. 100 Mbps Fast Ethernet link detected, no activity.
Green Blink Indicates data traffic on the 100Mbps Ethernet LAN.
Amber 0n 10 Mbps Ethernet link detected, no activity.
Amber Blink Indicates data traffic on the 10Mbps Ethernet LAN.
Power Ethernet Wireless

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
2-6 Introduction
202-10060-02, February 2005
WG602v3 Wireless Access Point Rear Panel
Figure 2-2: WG602v3 rear panel
Power Socket
This socket connects to the WG602v3 power adapter.
Reset and Restore to Factory Defaults Button
The reset and restore to defaults button located between the Ethernet RJ-45 connector and the
power socket resets the WG602v3 when pushed once or restores to the factory default settings
when pushed and held for 10 seconds.
RJ-45 Ethernet Port
Use the WG602v3 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such as
a hub, switch, or router.
Detachable Antenna
The WG602v3 provides a detachable antenna. Be sure the antenna is securely fastened.
Wireless Wireless LAN Link Activity Indicator
Off
Green On Indicates no wireless link detected. Wireless link enabled, no activity.
Green Blink Wireless link activity.
LED DESCRIPTION
Power
Socket
RJ-45 Ethernet
Port
Reset & Restore
Button
Detachable
Antenna

Basic Installation and Configuration 3-1
202-10060-02, February 2005
Chapter 3
Basic Installation and Configuration
This chapter describes how to set up your NETGEAR WG602v3 54 Mbps Wireless Access Point
for wireless connectivity to your LAN. This basic configuration will enable computers with
802.11b or 802.11g wireless adapters to do such things as connect to the Internet, or access printers
and files on your LAN.
You need to prepare these three things before you can establish a connection through your wireless
access point:
• A location for the WG602v3 that conforms to the guidelines below.
• A device such as a hub, switch, router, or Cable/DSL gateway.
• One or more computers with properly configured 802.11b or 802.11g wireless adapters.
Observing Placement and Range Guidelines
The operating distance or range of your wireless connection can vary significantly based on the
physical placement of the wireless access point. The latency, data throughput performance, and
notebook power consumption of wireless adapters also vary depending on your configuration
choices.
Note: Indoors, computers can connect over wireless networks at ranges of several
hundred feet or more. This distance can allow for others outside your area to access your
network. It is important to take appropriate steps to secure your network from
unauthorized access. The WG602v3 Access Point provides highly effective security
features which are covered in detail in this chapter. Deploy the security features
appropriate to your needs.
Note: Failure to follow these guidelines can result in significant performance
degradation or inability to wirelessly connect to the WG602v3.

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
3-2 Basic Installation and Configuration
202-10060-02, February 2005
For best results, place your wireless access point:
• Near the center of the area in which your PCs will operate.
• In an elevated location such as a high shelf where the wirelessly connected PCs have
line-of-sight access (even if through walls).
• Away from sources of interference, such as PCs, microwaves, and 2.4 GHz cordless phones.
• Away from large metal surfaces.
• If using multiple access points, it is better if adjacent access points use different radio frequency
Channels to reduce interference. The recommended Channel spacing between adjacent access
points is 5 Channels (for example, use Channels 1 and 6, or 6 and 11).
The time it takes to establish a wireless connection can vary depending on both your security
settings and placement.
Default Factory Settings
When you first receive your WG602v3, the default factory settings will be set as shown below. To
restore these defaults, see “WG602v3 Wireless Access Point Rear Panel” on page 2-6.
FEATURE FACTORY DEFAULT SETTINGS
User Name (case sensitive) admin
Password (case sensitive) password
Access Point Name NETGEARxxxxxx where xxxxxx are the last six digits of
the wireless access point's MAC address
DHCP DHCP client
IP Configuration
if DHCP server is unavailable IP Address: 192.168.0.227 Subnet Mask: 255.255.255.0
Gateway: 0.0.0.0
Wireless Mode (Access Point or Bridge) Access Point
Wireless Network Name (SSID) NETGEAR
Broadcast Network Name Enabled
802.11g/b
Radio Frequency Channel 11
WEP/WPA Disabled
Authentication Type Auto