NexSens X2 User manual

IMPORTANT - BEFORE FIELD DEPLOYMENT: Completely configure new X2 systems with sensors and a web connec-
tion in a nearby work area. Operate the system for several hours and ensure correct sensor readings. Use this test run to
become familiar with the features and functions.
To get started:
a. Go to WQDataLIVE.com
b. Create a new account or sign into an existing
account.
c. Choose or create the project that will contain
the data logger by selecting the Projects link
from the bottom right footer of the page.
d. Open the project and go to the ADMIN tab
located at the top of the project dashboard
and click Settings.
From there, choose the Project/Site pull down
menu and select the site for the new data logger.
a. If a site has not been created, select New Site.
Create and save the site before entering the
claim code.
Enter the claim code listed below into the space
provided under Assigned Devices.
Click Add Device.
a. The new device should be visible in the
Assigned Devices list.
X2 - IRIDIUM DATA LOGGER
QUICK START GUIDE
Overview
The X2 with iridium telemetry includes an integrated
satellite modem. Three sensor ports provide industry
standard protocols including SDI-12, RS-232, and RS-485.
The center port offers direct communication (serial to
PC) and power input. Smartphones and tablets connect
via WiFi.
Data is accessed and stored on the WQData LIVE web
datacenter. An easy-to-use dashboard and built-in sensor
library automatically facilitate setup and configuration.
What’s Included?
(1) X2 data logger
(1) X2 grounding kit
(3) Sensor port plugs, spare orings
(1) Power port plug, spare oring
(1) Oring grease
(1) Screwdriver with magnet tip
(1) Antenna with angle adapter
(1) Quick start guide
Figure 1: X2 Environmental Data Logger
WQData LIVE Setup
If iridium service is not purchased through
NexSens, visit the article link below to setup an
Iridium Short-burst data (SBD) account.
a. nexsens.com/wqsetiracc
b. If iridium activation is purchased through
NexSens, skip to the Data Logger Setup.

If using a Gmail for the SBD account, visit the
article below to provide WQData LIVE access to
transmit commands through the account.
a. nexsens.com/wqsetgmir

Iridium Account Setup

After 5 minutes, refresh WQData LIVE and
confirm the last contact time updates.
a. Updated data will appear at the next transmit
interval.
For additional information, please reference the X2 Resource Library on the NexSens Knowledge Base.
nexsens.com/x2kb
937-426-2703
www.nexsens.com
2091 Exchange Court
Fairborn, Ohio 45324
Connect power (5 to 24VDC) to the center port (6
pin) and ensure sensors are connected into the
port in which they were detected.
Figure 3: X2 LED light indicators.
LED
Color
Green
LED Light Indicators
1 Second
Interval
Blue
Yellow
Red
3 Second
Interval
5 Second
Interval
3 Blinks
Per
5 Seconds
Solid
Primary
power
heartbeat
Significant
system
error2
Secondary
power
heartbeat
Backup
power
heartbeat
Weak/No
cell signal
Data
acquisition
in progress
Strong
radio
signal
N/A
WQData
LIVE setup
successful1
Sensor
calibration
in progress
Table 1: X2 Environmental Data Logger LED Indicators.
1WQData LIVE setup is automatically done after sensor
detection.
2System errors can result from internal sensors detecting
high current, humidity, or pressure. These errors can
be indicative of a leak or other major problem with the
system that requires attention.
N/AN/A
N/A
N/A
N/AN/A
N/A
N/AN/A
N/A
Wait up to 60 seconds for the system to check
cellular coverage.
a. If the blue LED repeatedly blinks three times,
the cellular strength is sufficient to connect
the X2 with WQData LIVE.
b. If the blue LED repeatedly blinks once, cell
coverage is low. Move the X2 to a location with
better cell coverage and cycle power.

Visit the link below to enter the iridium account
information into the Advanced Device Remote
Configuration settings on WQData LIVE.
a. nexsens.com/wqconfir

Data Logger Setup
Follow the article below to use the CONNECT
software to set the proper settings on the X2 and
push the sensor configuration to the WQData
LIVE web datacenter.
a. nexsens.com/connirist

Figure 2: Sensor and power connection.