Nibe Contura C i30 User manual

C i30
www.contura.eu
Installation
Instructions

GB
82 CERTIFICATE
Declaration of performance according
to Regulation (EU) 305/2011
No. Ci30-CPR-130912-SE-2
PRODUCT
Product type Insert lit with solid biofuels
Type designation Contura i30
Manufacturing number See rating plate on the insert
Intended area of use Heating of rooms in residential buildings
Fuel Wood
MANUFACTURER
Name NIBE AB / Contura
Address Box 134, Skulptörvägen 10
SE-285 23 Markaryd, Sweden
CHECKS
According to AVCP System 3
European standard EN 13229:2001/AC:2006, EN-13229:2001/A2:2004/AC:2007
Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,
has checked declared performance and issued test report no. RRF-29 13 3371
The undersigned is responsible for the manufacture and conformity with the declared performance.
Niklas Gunnarsson, Business area manager NIBE STOVES
Markaryd, September 12, 2013
DECLARED PERFORMANCE
Essential characteristics Performance Harmonised technical
specification
Reaction to fire A1 WT
Minimum distance to combustible material Rear: 150 mm
Side: 150 mm
Follow the given conditions in the installation
instructions.
Risk of falling embers Pass
Emissions from combustion CO 0,07%
NOx 104 mg/m3
OGC 64 mg/m3
PM 17,1 mg/m3
Surface temperatures Pass
Cleaning options Pass
Mechanical durability Pass
Emissions of hazardous substances Pass
Nominal output 6,0 kW
Efficiency 81%
Flue gas temperature in connector at nominal
output
283°C
EN 13229:2001/AC:2006,
EN-13229:2001/A2:2004/AC:2007

GB
83
CONTENTS
WARNING!
The insert becomes very hot
During operation, certain surfaces of the insert become
very hot and can cause burn injuries if touched. Also,
take heed of the strong heat radiated through the door
glass. Placing flammable material closer than the safe
distance indicated may cause a fire. Smoulder combustion
can cause quick gas ignition with the risk of damage to
property and personal injury.
NOTE:
Report the installation of a fireplace to
your local authority.
The owner of the house is personally responsible
for ensuring compliance with the mandatory safety
requirements and must have the installation approved by
a qualified inspector. Your local chimney sweep must also
be informed about the installation as this will affect the
routines for regular chimney-sweeping services.
A warm welcome to Contura.
A warm welcome to the Contura family. We hope you
will get a great deal of pleasure from your new insert.
As a new owner of a Contura insert, you have secured
a product with timeless design and long service life.
Contura also has a combustion process that is both
environmentally friendly and efficient, for the best heat
production.
Read through these installation instructions carefully
before installation. Read how to best light your stove in
the lighting instructions.
List of Contents
Technical specifications 84
Important dimensions 85
Prior to installation 85
Installation 94
Chimney 95
Recessing the insert 96
Recess example 97

Eldstadsbeklädnad
Diffusor
Rökhylla
Spjäll
Typskylt
Asklåda
Roster
Motvikt
Strålningsplåt
Justerbara fötter
Anslutningsstos
Bottenisolering
GB
84
Smoke shelf
Counter weight
Grate
Adjustable feet
Connector
Bottom insulation
Ash-pan
Type plate
Damper
Hearth cladding/Thermotte
Diffuser
FACTS
Floor plate
If the floor under the stove is flammable,
it must be protected by a non-flammable
material e.g. natural stone, concrete or 0.7
mm thick metal. The floor in front of the
hearth opening must be protected against
any falling embers using non-flammable
material that covers an area at least 300
mm in front and 100 mm along each side
of the hatch opening. A toughened glass
hearth plate is available as an accessory.
Application to local authority
Before installing a stove or erecting a
chimney, it is necessary for you to make
an application for permission to your
local authority. Ask your local authority
for advice regarding regulations and the
application.
General
This manual contains instructions about
how Contura i30 must be assembled
and installed. To ensure the function
and safety of the insert, we recommend
that installation is carried out by an
authorised technician. Our Contura dealers
can recommend suitable technicians,
information about our dealers can be found
at www.contura.eu
Instructions for lighting are also supplied
with the insert. Read them carefully and
keep them safe for future use.
Structural support
Check that floor joists have the sufficient
load capacity for the insert, chimney and
construction parts that are used when
recessing.
Technical
specifications
Model i30
Output 4-9 kW
Nominal output 6 kW
Efficiency 80%
Weight (kg) 135 (with Thermotte)
95 (without Thermotte)
Width (mm) 725
Depth (mm) 410
Height (mm) 1260
Connector diameter Ø150 mm ext.
Type approved in accordance with:
European standard EN-13229
DIN plus
Bauart 1
Part 15a B-VG
Test report no: RRF-29 13 3371
SINTEF: 110-0405
Approved for installation in Smoke Control Area
by DEFRA
Heat deflector

C i30
750
630
110 110
1350-1370
1
1
2
430
200
925-945
85-105
30-50
60
390
330-350
Ø 150
110
1205-1225
Utv.
Tilluftsstos Ø100 Justerbar fot
GB
85
Prior to installation
Adjustable foot
Ext. Ø150
Air Inlet Ø100
IMPORTANT DIMENSIONS / PRIOR TO INSTALLATION
Important dimensions
Opening the door

3 mm
10 mm
GB
86
Remove the loose parts
from the firebox.
The insert is secured to the pallet by the
two rails, remove the screws and remove
the angle brackets. Reinstall the screws
on the legs before moving the insert
from the pallet.
PRIOR TO INSTALLATION

!
!
10 mm
GB
87
Check wire routing and
remove the transport
locking device!
The hatch runners are lubricated at the factory,
with special grease that can withstand high
temperatures. This type of grease is usually
difficult to find on the market and we recommend
contacting a Contura dealer to order this special
grease when lubricating the runners.
PRIOR TO INSTALLATION

1 2
5 6
3 4
GB
88
Installing the hearth cladding
PRIOR TO INSTALLATION

7 8
910
GB
89
PRIOR TO INSTALLATION

10 mm
1
2
PH2
GB
90 PRIOR TO INSTALLATION
Installing heat deflectors