Nice Domi WS Technical specifications

Domi
WS
WSC
WSR
EN - Instructions and warnings for installation and use
Climatic sensor

2– English
EN
max
1
4
2
3

English – 3
EN
10
0
20
30
40
50
70
80
60
90
“0”
instantaneous
wind speed
gust of wind
automatic
operation
manual
operation
momentary drops
in speed, within the
hysteresis values
hysteresis threshold:
positioned automatically
at half the set threshold
value
set threshold
value: e.g.
60 km/h
drops in speed lasting
less than 10 minutes
over-threshold
hysteresis
under-threshold
active manual
commands
active manual
commands
manual commands
deactivated
protection deactivated protection deactivatedafter 3 seconds after about 10 minutes
after 4 minutes
system active
5
km/h

4– English
EN
“0” “1”
presence/absence
of rain
automatic
operation
Not raining
Raining
manual
operation manual commands activated
system deactivated system deactivatedafter 10 seconds after 10 minutes
sensor dry
system active
6

English – 5
EN
“0”
“1”
5
0
10
15
20
25
35
40
30
45
light
intensity
automatic
operation
manual
operation
momentary drops
in light, within the
hysteresis values
set threshold
value: e.g.
30 klux
drops in light, within
the under-threshold
values
over-threshold
hysteresis
under-threshold
manual commands activated
system deactivated system deactivatedafter 2 minutes after 15 minutes
system active
hysteresis threshold: posi-
tioned automatically at half
the set threshold value
sunrise daytime dusk night-time
7
klux

6– English
EN
Quick reference
guide
Step 1 - Installation and connections
B
Rain sensor (WSR)
Solar cell (WSC)
Sun
sensor
Wind
sensor
Button
B button
Button
LED
1
2
5
7
6 8
4
3
A
B
100–240 V AC, 50/60 Hz
(WS and WSR only)

English – 7
EN
LEGEND
orange-off-green orange-off-green
C
D E WSC Activation WS / WSR Activation
(WS and
WSR only)
6 mm
15 mm
9
10
11
12
13
2/3
100–240 V AC
50/60 Hz
LLNN
LED OFF LED ON Press and hold the button
Green LED LED ash Release the button
Orange LED ... Multiple LED ashes Press and release
the button
Red LED Wait Observe / Check
14
15
16

8– English
EN
“B”
4
.sec.
“B”
4
.sec.
“B”
4
.sec.
3
3
8
.sec.
2
.sec.
01 02
01 02
2
.sec. ON
OFF
“B”
04
“B”
“B”
“B”
2
.sec.
Old
03
X 3
Hold down (2-4s) LED Release LED Hold down LED Wait Release Wait
3
3
8
.sec.
2
.sec.
01 02
01 02
2
.sec. ON
OFF
“B”
04
“B”
“B”
“B”
2
.sec.
Old
03
X 3
Press 3 times Hold down Wait Release Movements To escape the procedure at any point
(red) (red) (red)
Step 2b - Memorizing the sensor in BIDI mode with a previous transmitter
Hold down Wait Release Wiggle Press 1 time Wiggle
Hold down (6-8s) Sequence Release LED Press 1 time Wiggle
“LED” (red-
green-orange)
NOTE
Press 1 time Movements To escape the procedure at any point
NOTE
Step 2a - Memorizing the sensor in MONO mode with a previous transmitter
(orange)

English – 9
EN
0201
04
03
05
≥ 1klux ...
...
... “B”
1
.sec.
15
.sec.
Step 4 - Testing the “Sun” sensor
03
“SUN”
02
01
“B”
Start UP movement Press 1 time to stop
The “Sun” feature must be activated in the motor.
(green)
Illuminate the sensor Hold Down Wait LED Release Down Series of flashes
“LED” (green)
flashing
Step 3 - Conrming memorization
0201
04
03
05
≥ 1klux ...
...
... “B”
1
.sec.
15
.sec.
Cover the sensor Wait Up  Series of flashes Uncover the sensor
“LED” (green-red)
flashing
To escape the procedure at any point
NOTE

10 – English
EN
01
03
02
...
...
...
“W”
“W”
“W”
“B”
1
.sec.
01
03
02
...
...
...
“W”
“W”
“W”
“B”
1
.sec.
Hold down Wait LED Release Actuate the blades Up Series of flashes
Stop the blades Series of flashes Press 1 time (Down)
“LED” (red-green)
“LED” (red)
flashing
flashing
To escape the procedure at any point
NOTE
Step 5 - Testing the “Wind” sensor
“B”
2
.sec.
2
.sec.
3
.sec.
“B”
2
.sec.
2
.sec.
3
.sec.
Series of flashes Release Wait Series of flashes
Hold down Wait LED Release Finger on sensor Wait Up
“LED” (green-red)
flashing
(orange)
(red)
“LED” (orange)
flashing
Warning! The rain sensor may be hot (about 45°C).
To escape the procedure at any point
NOTE
Step 6 - Testing the “Rain” sensor