Nikon Eclipse E600W User manual

E600W/E600/E400
Teaching Head/Multi Teaching Head
Instructions
M189 E 03.7.VF.3

1
CAUTION
WARNING
Thank you for purchasing this Nikon product.
This instruction manual is written for users of the Nikon Microscope ECLIPSE
E600W/E600/E400 Teaching Head/Multi Teaching Head.
To ensure correct usage, read this manual carefully before operating the instrument.
•It is prohibited to reproduce or transmit this manual in part or whole without Nikon’s
expressed permission.
•The contents of this manual are subject to change without notice.
• Although every effort has been made to ensure the accuracy of this manual, if you
note any points that are unclear or incorrect, contact your dealer or nearest Nikon
representative.
• Some products introduced in this manual may not be included in the set you’ve
purchased.
• Be sure to read this together with the respective instruction manuals for the
microscope and other instruments being used.
Warning/Caution Symbols Used in This Manual
Although Nikon products are designed to provide you with the utmost safety during use,
incorrect usage or disregard of the instructions can cause personal injury or property
damage. For your safety, read this instruction manual carefully and thoroughly before
using the instrument. Do not discard this manual but keep it near the product for easy
reference.
In this manual, safety instructions are indicated with the symbols shown below. Be sure
to follow the instructions indicated with these symbols to ensure correct and safe
operation.
Symbol Meaning
Disregarding instructions marked with this symbol may lead to
death or serious injury.
Disregarding instructions marked with this symbol may lead to
injury or property damage.

2
WARNING
1. Intended product use
This product should only be used for microscopic observation. Do not use it for any other
purpose.
2. Do not disassemble
Disassembling may cause malfunction and/or electrical shock. Do not disassemble any
parts other than those mentioned in this manual. If you notice any malfunction, notify your
dealer or nearest Nikon representative.
3. Read all instruction manuals thoroughly
To ensure safety, thoroughly study this instruction manual as well as the instruction manuals
for all other units being used. Adhere strictly to the warnings and cautions given at the
beginning of these instruction manuals.
When using this product in combination with an Epi-fluorescence attachment, be sure to
read its instructions. Care is required when handling the mercury lamp used as the light
source for the Epi-fluorescence attachment.
CAUTION
1. Turn the power off when assembling the system, connecting or disconnecting
cables and replacing the lamp
To prevent electrical shock and damage, be sure to switch off the power switches on the
microscope, power supply, etc., and to unplug the power cord from the wall outlet before
connecting or disconnecting cables and replacing the lamp.
2. Do not wet the instrument
If the microscope or the power supply gets wet, a short circuit may result that could damage
the equipment or make it extremely hot. If you accidentally spill a liquid on the instrument,
immediately turn off the power switch and unplug the power cord. Then use a dry cloth to
wipe away the moisture. If any liquid gets inside the instrument, do not use it; instead,
notify your dealer or nearest Nikon representative.
3. Precautions for assembly
Be careful not to pinch your hands or fingers when assembling the instrument.

3
Notes on Handling the Instrument
1. Handle the instrument with care
This product is a precision optical instrument. Always handle it with care and do not subject it
to strong physical shock.
2. Lense cleaning
Do not let dust, fingerprints, etc. get on the lenses. Dirt on the lenses, mirrors, etc. will
adversely affect the view of the image. If any of the lenses gets dirty, clean it as described in
section “V. Care and Maintenance.”
3. Installation location
The following conditions should be kept in mind when selecting the location for installation:
•Install the instrument on a surface with little vibration.
• Install the instrument in a location which is not exposed to direct sunlight.
• Install the instrument in a location which is free from dust.
•Do not install the instrument in a warm and humid location (where the temperature is above
40°C or the humidity is above 80%). In such a location, mold or condensation may form on
the lenses or filters.
4. Use of accessories
This attachment splits the light to allow several observers to view the same image
simultaneously. Due to the working principles of the attachment, the brightness of the image is
reduced as the number of observers is increased. The light source produces sufficient light
intensity to allow normal observation of an image with adequate brightness by adjusting the
ND filters inserted in the microscope main unit (main observer’s section).
However, depending on the accessories being used, adequate brightness may not always be
obtained. Please consult your dealer or nearest Nikon representative before using accessories.
5. Pointer and AC adapter
The AC adapter to be connected to the pointer should always be the one provided with the
pointer. The use of any other type of AC adapter could result in accidents or damage to the
instruments.

4

5
Contents
Warning/Caution Symbols Used in This Manual ........................................ 1
WARNING......................................................................................... 2
CAUTION ......................................................................................... 2
Notes on Handling the Instrument ...................................................... 3
IComponents of the System ......................................................... 6
II Microscopy.................................................................................... 8
III Assembly .................................................................................... 10
IV Troubleshooting ......................................................................... 17
VCare and Maintenance ............................................................... 18
VI Specifications ............................................................................. 20

6
IComponents of the System
If the system has not yet been assembled, see section “III. Assembly” first.
For details on assembling and handling the microscope, see the instruction manual supplied with
the microscope.
This attachment can be mounted on the ECLIPSE E600W, E600 or E400 microscope. Note that
the illustrations in this manual shows the ECLIPSE E600 microscope for convenience. (The
microscopes ECLIPSE E800 and E1000 only allow mounting of the dual-viewing (side-by-side)
attachment. The inverted microscopes TE300 and TE200 only allow mounting of the dual-
viewing (side by side), the triple-viewing and the multi-viewing (for 5 persons) attachment.
Separately available components are required for mounting on these microscopes. For details,
see P.12.)
Depending on the type of set you have purchased, some of the following components may not be
included.
Dual-viewing (face-to-face)
This model allows the main observer and the secondary observer to
be positioned face-to-face during observation.
Components
1) Microscope
2) Teaching head F-F
3) Pointer
4) AC adapter
5) Eyepiece tube for secondary observer
6) Eyepieces for secondary observer
Dual-viewing (side-by-side)
This model allows the main observer and the secondary observer to
be positioned side-by-side during observation.
This model can also be mounted on the microscopes ECLIPSE
E800, E1000 and the inverted microscopes TE300 and TE200 with
the separately available components. (Please refer to P.12 for
details.)
When a pointer is going be used, assemble the system so that the
secondary observer will be positioned on the right. If reversed, the
pointer control section will be at the rear of the microscope.
Components
1) Microscope
2) Teaching head S-S
3) Pointer
4) AC adapter
5) Eyepiece tube for secondary observer
6) Eyepieces for secondary observer
7) Support stand
G
6)
2)
4)
1)
3)
5)
Heat protection
shield
G
4)
7)
5)
3)
1)
6)
2)
Mounting ring
Height adjustment
clamp screw

7
Triple-viewing
This model allows two secondary observers to be
positioned face-to-face on either the left or right
side of the main observer during the observation.
This model can also be mounted on the inverted
microscopes TE300 and TE200 with the
separately available components. (Please refer to
P.13 for details.)
Components
1) Microscope
2) MTH main splitter
3) Pointer
4) AC adapter
5) MTH relay unit
6) Eyepiece tube for secondary observer (×2)
7) Eyepieces for secondary observer (×2 sets)
8) Support stand
Multi-viewing for 5 persons
This model allows two secondary observers to be
positioned face-to-face on both sides of the main
observer during observation.
This model can also be mounted on the inverted
microscopes TE300 and TE200 with the
separately available components. (Please refer to
P.14 for details.)
Components
1) Microscope
2) MTH main splitter
3) Pointer
4) AC adapter
5) MTH relay unit (×2)
6) Eyepiece tube for secondary observer (×4)
7) Eyepieces for secondary observer (×4 sets)
8) Support stand (×2)
Multi-viewing for 10 persons
Components
1) Microscope
2) MTH main splitter
3) Pointer
4) AC adapter
5) MTH relay unit (×2)
6) Teaching head F-F
7) Teaching head S-S (×4)
8) Eyepiece tube for secondary
observer (×9)
9) Eyepieces for secondary observer
(×9 sets)
10) Support stand (×6)
G
4)
1)
3)
8)
7)
5)
6)
2)
G
1)
3)
8)
7)
5)
6)
2)
4)
I. Components of the System
G
1)
3) 5)
4)
2)
10)
7)
8) 9)
6)

8
II Microscopy
If the system has not yet been assembled, see section “III. Assembly” first.
For details on assembling and handling the microscope, see the instruction manual supplied
with the microscope.
Depending on the type of set you have purchased, some of the components described below
may not be included.
1Adjust the microscope correctly.
The secondary observer will view the same image as the main observer. If the main observer
does not adjust the microscope correctly, the secondary observer will not be able to view a
correct image. Also when the main observer did not perform the diopter adjustment, the
secondary observer is likely to have his image out-focused each time the main observer
changes the objective magnification. Be sure to perform the diopter adjustment referring to the
instruction manual supplied with the microscope.
2Adjust the diopter setting at the secondary observer’s position as
well.
After the main observer has adjusted the microscope correctly, the secondary observer should
bring the image into focus with the diopter adjustment rings. Set the dioptor adjustment rings
for both the left and right eyes.
3Method for simple diopter adjustment
When a pointer is attached to the system, turn the respective diopter adjustment rings on the
left and right eyepieces to bring the arrow into focus. It is needed to change the arrow color to
green, and to move the arrow to near the center of view field in advance. This completes
diopter adjustment.

9
4Using the pointer
G
R
Lamphouse cover
Allow the lamp to cool
before replacement
(p.16).
Before replacing the
lamp, turn the arrow
brightness control
counterclockwise until it
clicks to turn off the
arrow and unplug the
AC adapter plug from
the wall outlet.
Arrow rotation dial
Use this to change the direction of
the arrow.
Arrow color selector dial
Turning the dial to the "G" position
changes the color to green, and turning it
to the R position changes it to orange.
(Turn the dial as far as it will go.)
Arrow brightness control
(also functions as
the ON/OFF switch)
Turn the control clockwise to
increase arrow brightness.
Turn it counterclockwise until it
clicks to turn OFF the power
and to make the arrow
disappear.
Arrow control stick
Use this to move the arrow.
II. Microscopy

10
III Assembly
The assembly procedure for the system is shown below. Assemble it according to the numbers
indicated in the illustrations.
For details on assembly of the microscope and other components being used, see the respective
instruction manuals.
Be sure not to scratch or leave fingerprints on lenses and filters when assembling them, as this
will adversely affect the image quality.
For details on the installation location, see the section “Notes on Handling the Instrument” at
the beginning of this instruction manual.
WARNING
Before using this attachment, be sure to read the “ WARNING”,
“CAUTION” and “Notes on Handling the Instrument” sections at the beginning
of this instruction manual. Adhere strictly to the WARNING and CAUTION
instructions.
Be sure to also read the instruction manuals for all other equipment (microscope,
etc.) being used and adhere strictly to the warning and caution instructions. In
particular, when the attachment is used in combination with an Epi-fluorescence
attachment, be sure to read the instructions provided with the Epi-fluorescence
attachment. Care is required when handling the mercury lamp used as the light
source for the Epi-fluorescence attachment.
To prevent electrical shock, fire and accidents, always turn OFF the power switch on
the microscope, power supply, etc., and unplug the power cord from the wall outlet
before assembly.
Tools needed
•One hexagonal screwdriver (provided with the microscope) 1.3 mm
(When a pointer is to be attached, you also need)
• One hexagonal wrench (provided with the pointer) 3 mm

11
III. Assembly
1
2
3
4
Clamp for 2
Clamp for 1
Check that the
serial numbers of
the teaching head
S-S are the same.
1
Clamp for 3
Clamp for 2
Pointer mounting
surface
Clamp for 6
Clamp for 7
Clamp for 5
Secondary
observer
section
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
Place
horizontally
Upper surface should
also be horizontal.
4
2
3
6
57
Nikon
Nikon
0100001
Y-THF
JAPAN
0100001
Y-THF
JAPAN
Main observer
section
1Assembly for the dual-viewing (face-to-face) model
2Assembly for the dual-viewing (side-to-side) model
1Check that the serial numbers on the two components (main observer section and
secondary observer section) of the teaching head S-S are identical. (If the numbers are
different, observation will be adversely affected. In this case, please contact your
dealer or nearest Nikon representative.)
2Adjust the height of the support stand so that the main observer section and the
secondary observer section are horizontal. This step is facilitated by first adjusting the
support stand to an approximate height before attaching the stand.
3When a pointer is going to be used, assemble the system so that the secondary observer
will be positioned on the right. If reversed, the pointer control section will be at the
rear of the microscope.
4When mounting the attachment on the microscopes ECLIPSE E800 and E1000, or on
the inverted microscopes ECLIPSE TE300 and TE200, separately available
components are required.
Mounting on the ECLIPSE E400, E600 or E600W

12
Mounting on the ECLIPSE E800 or E1000
(The E600TH mounting adapter and E400/600 eyepiece tube are required.)
Mounting on the ECLIPSE TE300 or TE200
(The TE-TI intermediate eyepiece tube and E400/600 eyepiece tube are required.)
Check that the
serial numbers of
the teaching head
S-S are the same.
1
Nikon
Nikon
0100001
Y-THF
JAPAN
0100001
Y-THF
JAPAN
Clamp for 7
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
Clamp for 8
Clamp for 3
5
7
Upper surface should
also be horizontal.
Place horizontally
8
Clamp for 6
6
Clamp for 4
Pointer mounting
surface
E600TH mounting
adapter
Eyepiece tube
for E400/E600
3
2
4
Clamp for 7
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
Clamp for 8
5
7
Upper surface should
also be horizontal.
Place horizontally
Clamp for 6
6
8
Clamp for 4
Clamp for 2
Clamp for 3
3
2
4
Check that the
serial numbers of
the teaching head
S-S are the same.
1
Nikon
Nikon
0100001
Y-THF
JAPAN
0100001
Y-THF
JAPAN
Pointer mounting
surface
Eyepiece tube
for E400/E600
TE-TI intermediate
eyepiece tube

13
3Assembly for the triple-viewing model
1Check that the serial numbers on the two components (on the main section and the
relay section) of the MTH relay unit are identical. (If the numbers are different,
observation will be adversely affected. In this case, please contact your dealer or
nearest Nikon representative.)
2Adjust the height of the support stand so that the main observer section and the
secondary observer section are horizontal. This step is facilitated by first adjusting the
support stand to an approximate height before attaching the stand.
3In the illustration below, the secondary observers are positioned on the right side of the
main observer, but they may also be positioned on the left. Attach the MTH main
splitter so that the pointer mounting surface is facing towards the front.
4When mounting the attachment on the inverted microscopes TE300 and TE200, the TE-
TI intermediate eyepiece tube and E400/600 eyepiece tube are required. Attach the TE-
TI intermediate eyepiece tube instead of the original eyepiece tube and mount the MTH
main splitter on it.
See the illustration on P.12 for the installation of the TE-TI intermediate eyepiece tube.
[Remarks]
If a trinocular eyepiece tube T is used for the main observer section, you can provide the image to the vertical
tube of the eyepiece tube by setting the optical path to the “BINO & PHOTO” position. If the ND filter is
removed in advance from the eyepiece tube mounting port of the MTH main splitter, the main and the secondary
observers will be able to view an image with more uniform brightness. This should be convenient such as when
performing the TV observation.
1
0
0000
1
0
0
0000
0
MTH relay unit
Main section
Relay section
Place
horizontally
Check that the
serial numbers
are the same.
1
2
Clamp for 8
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
6
9
Upper surface
should also be
horizontal.
Clamp for 7
7
8
Clamp for 9
MTH relay unit
MTH main splitter
Clamp for 5
Ensure that the pointer
mounting surface faces
the front.
Clamp for 3
3
4
5
ND filter (φ28 mm)
Secondary
observer section
Main observer section
III. Assembly

14
[Remarks]
If a trinocular eyepiece tube T is used for the main observer section, you can provide the image to the vertical
tube of the eyepiece tube by setting the optical path to the “BINO & PHOTO” position. If the ND filter is
removed in advance from the eyepiece tube mounting port of the MTH main splitter, the main and the secondary
observers will be able to view an image with more uniform brightness. This should be convenient such as when
performing the TV observation.
4Assembly for the multi-viewing model by 5 persons
1Check that the serial numbers on the two components (on the main section and the
relay section) of the MTH relay unit are identical. (If the numbers are different,
observation will be adversely affected. In this case, please contact your dealer or
nearest Nikon representative.) Two sets of MTH relay units are required. Assemble
those components with identical serial numbers to each other.
2Adjust the height of the support stand so that the main observer section and the
secondary observer section are horizontal. This step is facilitated by first adjusting the
support stand to an approximate height before attaching the stand.
3When mounting the attachment on the inverted microscopes TE300 and TE200, the TE-
TI intermediate eyepiece tube and E400/600 eyepiece tube are required. Attach the TE-
TI intermediate eyepiece tube instead of the original eyepiece tube and mount the MTH
main splitter on it.
See the illustration on P.12 for the installation of the TE-TI intermediate eyepiece tube.
1
0
0000
1
0
0
0000
0
MTH relay unit
Main section
Relay section
Place
horizontally
Check that the
serial numbers
are the same.
1
2
Clamp for 8
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
6
9
Upper surface
should also be
horizontal.
Clamp for 7
7
8
Clamp for 9
MTH relay unit
MTH main splitter
Clamp for 5
Ensure that the
pointer mounting
surface faces
the front.
Clamp for 3
3
4
5
Assemble in the same
manner as that for
the right side.
Secondary
observer section
Secondary
observer
section
Main observer section
ND filter (φ28 mm)

15
III. Assembly
5Assembly for the multi-viewing model by 10 persons
1Check that the serial numbers on the two components (on the main section and the
relay section) of the MTH relay unit are identical. (If the numbers are different,
observation will be adversely affected. In this case, please contact your dealer or
nearest Nikon representative.) Two sets of MTH relay units are required. Assemble
those components with identical serial numbers to each other.
2Check that the serial numbers on the two components (on the main observer’s section
and the secondary observer’s section) of the teaching head S-S are identical. (If the
numbers are different, observation will be adversely affected. In this case, please
contact your dealer or nearest Nikon representative.) Four sets of teaching head S-S are
required. Assemble those components with identical serial numbers to each other.
3Adjust the height of the support stands so that the main observer section and the
secondary observer sections are horizontal. This step is facilitated by first adjusting the
support stands to an approximate height before attaching the stands.
Check that the
serial numbers of
the teaching head
S-S are the same.
3
Nikon
Nikon
0100001
Y-THF
JAPAN
0100001
Y-THF
JAPAN
Clamp for !7
Clamp for !2
Clamp for 5
Clamp
for !1
7
5
4
Place
horizontally
Place
horizontally
12
14
16
11
1
0
0000
1
0
0
0000
0
MTH relay unit
Main section
Relay section
Check that the
serial numbers
are the same.
1
2
17
Clamp
for !5
15
13
Clamp for !0
Clamp
for !3
Height adjustment
clamp screw
Adjust to an
approximate height
and readjust later.
9
6
10
8
Assemble in the
same manner
as that for the
right side.
Clamp for 4
ND filter
(φ28 mm)

16
6Mounting the pointer
Mount the pointer on the front side of the main observer section with the provided hexagonal
wrench. When a multi-viewing attachment for 10 persons is being used, mount the pointer on
the lower part (the front side of the MTH main splitter).
Be sure to use the AC adapter provided with the pointer.
<Attaching/replacing the lamp>
Allow the lamp to cool before replacing it. Before replacing the lamp, turn the arrow
brightness control counterclockwise as far as it will go to turn off the arrow and then unplug
the AC adapter plug from the wall outlet.
1Push and turn the lamphouse cover approximately 45°counterclockwise to remove it.
2Position the illuminating part of the lamp inward and insert the lamp into the socket.
3Return the lamphouse cover to its original position. (Align the protrusion with the
notch and turn the cover clockwise as far as it will go.)
G
Plastic cover
Pointer
AC adapter
To the power cord
G
R
Protrusion
Lamphouse
cover
Lamp
Notch
Illuminating part
III. Assembly

17
IV Troubleshooting
Focus differs among the main and secondary observer positions.
→The diopter setting has not been adjusted correctly. →Adjust the diopter setting
correctly. (P.8)
→The components with different serial numbers are →Reassemble the components
put together. with the identical serial
numbers to each other.
The arrow is not visible when the pointer is used.
→The arrow is outside of the view field. →Use the arrow control stick and
bring the arrow into the view
field.
→The arrow color selector dial is in an intermediate →Turn the dial in the preferred
position. direction as far as it will go.
→The arrow brightness control is OFF. →Turn the control clockwise.
→The AC adapter is not connected. →Connect the AC adapter.
→The lamp is burned out or no lamp is mounted. →Mount a new lamp. (P.16)
When using the pointer, the arrow and the specimen are not in simultaneous
focus.
→The diopter setting has not been adjusted correctly. →Adjust the diopter setting
correctly. (P.8)
The arrow is blurred when the pointer is used.
→The arrow is too bright. →Turn the arrow brightness
control counterclockwise to
reduce the brightness.

18
VCare and Maintenance
1Lens and filter cleaning
Do not let dust, fingerprints, etc. get on the lenses and filters. Dirt on the lenses, filters, etc.
will adversely affect the view of the image. If any of the lenses or filters gets dirty, clean it as
described below.
•Use a blower, etc. to blow away dust. If this is not sufficient to remove the dust, brush
away with a soft brush or gently wipe away with gauze.
•To remove fingerprints or grease, use a piece of soft, clean cotton cloth, lens tissue, or
gauze moistened with absolute alcohol (ethyl alcohol or methyl alcohol). However, do
not wipe twice with the same part of the cloth.
•Use petroleum benzine to clean off immersion oil. Wiping with absolute alcohol (ethyl
alcohol or methyl alcohol) will complete cleaning.
If petroleum benzine is not available, use methyl alcohol. Note that the cleaning
effectiveness of methyl alcohol is low and it will be necessary to repeatedly wipe.
(Normally, wiping three or four times is sufficient.)
•Be sure to use petroleum benzine only for cleaning off immersion oil from objectives.
Do not use it for cleaning eyepiece tube entrance lenses, filters, etc.
•Absolute alcohol and petroleum benzine are both highly flammable. Be careful when
handling them, when around open flames, or when turning the power switches ON and
OFF.
•Follow the instructions provided by the manufacturer when using absolute alcohol and
petroleum benzine.
2Cleaning painted components
Do not use organic solvents such as alcohol, ether or paint thinner on painted components,
plastic components or printed components. Doing so could result in discoloration or in peeling
of the printed characters. For persistent dirt, dampen a piece of gauze with neutral detergent
and wipe lightly.

19
V. Care and Maintenance
3Storage
Store the instrument in a dry place where mold is not likely to form.
Store the objectives, eyepieces, filter blocks, etc. in a desiccator or similar container with a
drying agent.
Protect the instrument from dust by covering it with the vinyl cover.
Before putting on the vinyl cover, turn off the power switch on the microscope and other
equipment, and wait until the lamphouse has cooled.
4Regular inspection
Regular inspection of this attachment is recommended to maintain optimum performance.
Contact your dealer or nearest Nikon representative for details about regular inspection.