NiteRider PRO 2200 RACE User manual

150-23274
Pro 2200 Race
User Guide
BATTERY CHARGING AND CARE
1. Plug the AC Adapter into an electric outlet, then plug
the cable from the AC Adapter into the battery.
2. The LED indicator on the battery will turn red while the
battery is charging. When the battery is fully charged,
the LED will turn blue.
3. Unplug the AC Adapter from the battery by grasping
the connectors rather than the cable.
4. Leaving the battery and AC Adapter connected
indenitely will not harm the battery or AC adapter.
5. When storing for an extended period of time,
charge the battery every three months to maximize
it’s lifespan.
RIDING AT NIGHT
While a Pro 2200 Race lighting system will improve
your view, control and enjoyment of night riding,
please remember that cycling at night is an inherently
dangerous activity. In addition to using your lighting
system properly and riding with extreme caution,
NiteRider urges you to:
• Never ride alone
• Always let someone know where you are going
• Wear a helmet and reective clothing
• Carry an auxiliary light and emergency supplies
• Make sure the headlamp, mounting bracket and
battery are securely fastened
• Always disconnect the battery from the
headlamp when transporting the light system
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize its lifespan (see the
“Battery Charging and Care” section for detailed information).
The Pro 2200 Race will perform in wet weather conditions,
but submerging it in water will damage the system.
SUPPORT
If you experience diculties during product installation or
operation, NiteRider provides free telephone support on
weekdays from 8:00 AM to 4:30 PM (Pacic Time)
at 800.466.8366, ext 4. You may also e-mail us at
[e-mail].
WARRANTY
NiteRider stands behind its products with the following
warranties:
• Lifetime warranty on all mechanical components
• 2 years on electrical components
• 1 year on rechargeable batteries
To obtain warranty service, it is preferable to have your
original sales receipt. Contact the NiteRider customer
service department at 800.466.8366, ext 4 to obtain a
Return Merchandise Authorization (RMA) number. The
RMA number must be prominently displayed on the outside
of your package. The product must be properly packaged
to prevent damage in transit.
For complete warranty information, please visit our
website at www.niterider.com.
RUN TIMES
The Pro 2200 Race will run up to:
Light Level
High
Medium
Low
Race**
Walk
Run Times*
1:15
2:30
5:00
12:00
34:00
Lumens
2200
1200
600
250
80
*Run Times are approximations and will vary.
**Race mode is intended for endurance races.
NiteRider Technical Lighting Systems, Inc.
8295 Aero Place, Suite 200
San Diego, CA 92123
www.niterider.com
Fuel Gauge
The 8-step, LED fuel gauge is located
on top of the headlamp in front of the
power button. When all four LED’s
are lit solid green, the battery is fully
charged. As the battery discharges
⅛ increments of capacity, the LED’s from right to left,
successively go from solid green to blinking green, to out.
With only the nal ⅛ capacity remaining one LED blinks red.
At this time, the headlamp should be turned o and the
battery recharged.

MOUNTING THE HEADLAMP
The Pro Series headlamp can be mounted to the handlebar
or a helmet.
Universal Handlebar Mount
The Universal Handlebar
Mount(UHM) is designed to
t on virtually any handlebar.
Included with the mount is a 2.5
mm Allen wrench for adjusting
the mount.
1. Turn the knob counter-clock-
wise, allowing the hinge
to swing open.
2. Place the UHM on the handlebar on the left side the stem,
orienting the rectangular notch in the slider clip to the rear.
3. Swing the hinge down to make contact with the handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the mount to
the handlebar.
The UHM can be adjusted to accommodate any handlebar
angle. By loosening the 2.5 x 30 mm Allen screw, you can
move the swing arm back and forth to straighten the headlamp.
Tighten the 2.5 x 30 mm screw after the adjustment. To pivot
the headlamp, loosen the 2.5 x 12 mm screw located under the
slider clip and swing arm and rotate the
headlamp to the desired position. Make
this adjustment before tightening the
2.5 x 30 mm screw.
Inserting the Headlamp into the
Handlebar or Helmet Mount
Insert the headlamp into the handlebar or helmet mount slider
clip from the rear forward. Gently rocking the lamp as you slide
it may help. Do not push the release lever when inserting the
headlamp into the slider clip; let the lamp snap into place by
itself. To remove the headlamp, push the release
lever forward and slide the lamp backward.
Note: After mounting the headlamp, adjust it so
the beam illuminates the road properly without
distracting oncoming riders.
Helmet Mount
1. Unclamp the straps on each side of
the helmet mount and pull them free.
2. Position the plastic mounting plate as
close to the centerline of the helmet
as possible, orienting the parallel
grooves on the slider clip to the rear.
3. Feed each strap into and out of two
helmet vents, circling each strap back to
the upper edge of the corresponding clamp.
4. Fasten the straps by inserting them
into the clamps and snap shut.
MOUNTING THE BATTERY
Warning: For safety reasons, a cyclist should never be tethered
to the bike. If the headlamp is mounted to the helmet, do not
mount the battery to the frame. Conversely, if the
headlamp is mounted to the handlebar, do not place the battery
in a pocket or pack.
Frame Mount
1. Thread the velcro straps through the two slots on the bottom
of the battery.
2. Attach the concave surface of the battery to a safe,
convenient location on the frame (typically under the top or
down tube), placing the velcro strap over the tube, but under
any shift or brake cables. The cable from the battery should
extend toward the stem.
3. Secure the headlamp and battery cable to the frame using
the thin velcro strapettes. Make sure the cables do not
interfere with any moving parts.
Pocket or Pack
1. Route the 36” extension cable through a helmet vent or
along the outside of the helmet using the thin velcro
strapette to secure the cable.
2. Connect the 36” extension cable to the battery, making sure
the cable does not interfere with any moving parts.
3. Simply place the battery in a pocket or pack.
OPERATION
1. Connect the headlamp cable to the battery.
2. Press and release the headlamp power button to turn
the light on. Cycle through the four brightness levels by
pressing and releasing the power button.
3. To access the daylight safety ash mode, press and hold
the power button until the headlamp starts to ash.
4. With the headlamp in ash mode, press and release the
power button to access Beacon, S.O.S. or Walk. From walk
mode you can return to normal mode by pressing and
releasing the power button.
5. To turn the headlamp o from normal, ash or walk modes,
press and hold the power button until the headlamp shuts o.
6. Always disconnect the battery from the headlamp when
transporting the light system to prevent accidentally
turning on the headlamp which may cause overheating
and potential damage from high heat or even a risk
of re.
D.
E.
F.
DISCOVER THE NIGHT
Thank you for choosing the Pro 2200 Race from NiteRider, the innovator
in technical lighting systems. The Pro 2200 Race combines a high-
powered white LED headlamp and a Li-Ion battery.
To get the most from your NiteRider light, we urge you to familiarize
yourself with the following safety and operating instructions.
PARTS LIST AND IDENTIFICATION
Please verify the contents of your Pro 2200 Race system:
A. Pro 2200 Race Headlamp
B. Li-Ion Race Battery (4 cell, 7.4v)
C. Universal Handlebar Mount (UHM)
D. Helmet Mount
E. 36” Extension Cable
F. A/C Adapter
Release
Lever