
EN
Instructions
Thank you very much for your purchase of this NITTO KOHKI product.
Before using your tool, please read this manual carefully so that you may use it properly to get the most out of it.
Please keep the manual handy - so you can use it whenever necessary.
Contents
Instructions ........................................................... ii
Product Specific Safety Rules .............................. 1
1. Product Overview ............................................. 3
Application ............................................................3
Channel.................................................................4
Checking inside the package ................................5
Part names............................................................6
Specifications ........................................................9
2. Preparation ..................................................... 13
Attaching a bit .....................................................13
Attaching the suspension bail .............................13
Mounting a vacuum pickup .................................14
Mounting a flange coupling .................................15
3. Basic Operation .............................................. 16
Start ....................................................................16
Changeover switch .............................................17
Start and stop......................................................18
Screw fastening mode ........................................19
4. Manual Mode .................................................. 21
For channel change type "CH PAT"
(channel pattern) .................................................21
For channel change type "INPUT"
(external signal) ..................................................23
5. Reset Mode .................................................... 24
Resetting the screw count...................................24
Restoring the operation channel .........................25
6. Setting Mode .................................................. 26
7. Channel Setting .............................................. 28
Screw fastening type (No.1 FSTN-TYPE)...........30
Screw count (No.2 COUNT) ...............................30
Fastening speed (No.3 SPEED) /
Torque (No.4 TORQUE) ......................................30
Initial speed (No.5 1stSpeed) /
Initial speed time (No.6 1stTime) ........................30
Midterm speed (No.7 2ndSpeed) /
Midterm speed time (No.8 2ndTime) ..................32
Reverse speed (No.9 RvsSpeed) .......................32
Screw fastening measurement lower limit
(No.10 CRT-L) / Screw fastening measurement
upper limit (No.11 CRT-U) ...................................32
Workpiece signal (No.12 WORK) .......................33
Workpiece setup time (No.13 WORK-S-T) .........34
Screw fastening OK signal (No.14 OKsig) ..........34
OK output timing (No.15 OKTiming) ...................34
Screw fastening confirmation time
(No.16 CHECK-T) ...............................................34
Operation OK sound (No.17 OK-BUZZ) /
Operation NG sound (No.18 NG-BUZZ) /
Count up sound (No.19 CU-BUZZ) .....................35
Auto reverse (No.20 AUTO-RVS) .......................35
Reverse time (No.21 RvsTime) ...........................35
Count return (No.22 COUNT-RTN) .....................36
Bit brake (No.23 BitBrake) ..................................36
Refastening prohibited time (No.24 REFST-T) ...36
Screwdriver LED (No.25 LED) ............................37
Screw fastening direction (No.26 SCREW) ........37
8. Channel Pattern Setting ................................. 38
9. Common Settings ........................................... 40
Channel change type (CH CHANGE) .................41
Measurement method (MEASURE) ....................41
Check buzzer sound (CHECK BUZZ) .................41
Buzzer volume (BUZZ VOL) ...............................41
Screw fastening NG check (NG WAIT) ...............41
LCD back light (BACK LIGHT) ............................41
Setting lock (SETTING LOCK)............................42
Manual mode (MANUAL MODE) ........................43
Reset (RESET) ...................................................43
Caution mode (CAUTION MODE) ......................43
Torque check mode (TORQUE CHECK) ............44
Idling NG time (IDLING NG) ...............................44
Initialization of settings ........................................44
10. Setting Transmission .................................... 45
11. Torque Check Mode ...................................... 46
12. Using External Signals ................................. 47
External I/O signal specifications ........................47
Connecting external signals ................................48
I/O circuit specifications ......................................48
I/O signal connection examples ..........................49
Timing of I/O signal .............................................51
Using external I/O signal .....................................52
13. Using External Signals (RS-232C) ............... 55
RS-232C specifications.......................................55
RS-232C connection ...........................................56
Command ...........................................................56
14. Error Detection ............................................. 58
Screw fastening NG ............................................58
System error .......................................................58
15. Appendix .......................................................59
When an abnormality has occurred
(Troubleshooting) ................................................59
Maintenance and Inspection ...............................63
Disposal ..............................................................63
Separately-sold products ....................................64
External dimensions............................................66
About screw fastening type .................................68
Channel/channel pattern setting example...........70
Glossary ..............................................................72
Index ...................................................................75
Setting memo ......................................................77
TV08057-0DLV45Cen.indbiiTV08057-0DLV45Cen.indbii 2019/10/3012:59:592019/10/3012:59:59