Noble House Home Furnishings Armless Chair User manual

Assembly Instructions
Armless Chair
Caution: This Chair is NOT a TOY.
Keep your child/children at bay during the assembly process.
Whenever moving/lifting the Chair and to prevent damage to the Chair, two
adults are needed to execute these actions.
Caution: You must read this before you proceed.
Noble House Home Furnishings LLC 1 of 11

No. Qty
A 1
B 1
C 1
D 1
E 1
F 1
G 1
H 1
No. Qty
①9
②5
③1
Picture
Before Beginning Assembly:
Backrest Panel
Bolt
(M6x35mm)
Allen Key
Back Support Bar
Description
Picture
Part List
Hardware
Left Panel
(with Pre-installed
Levellers)
Screw
(M6x55mm)
Description
Right Panel
(with Pre-installed
Levellers)
Front Support Bar
Seat Panel
Assembly Preparation
Back Cushion
Seat Cushion
Noble House Home Furnishings LLC 2 of 11

Noble House Home Furnishings LLC 3 of 11

Step 1
Overview
This Armless Chair has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Armless Chair parts, the above picture is to help you
put the various parts into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
Assembly Steps
FRONT FACING
Backrest Panel (A)
Right Panel (C)
Left Panel (B)
Seat Panel (D)
Seat Cushion (G)
Back Support
Bar (E)
Back Cushion (H)
Front Support Bar (F)
Noble House Home Furnishings LLC 4 of 11

Step 2
Place Left Panel(B) facedown as pictured.
Insert dowels on Back Support Bar(E) and Front Support Bar(F) into mountings on
Left Panel(B).
Attach Back Support Bar(E) and Front Support Bar(F) to Left Panel(B) using Bolts(①)
with Allen Key(③).
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC 5 of 11

Step 3
Insert dowels on Backrest Panel(A) into mountings on Left Panel(B).
Attach Left Panel(B) to Backrest Panel(A) using Bolts(①) with Allen Key(③).
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC 6 of 11

Step 4
Place the Right Panel(C) facedown as pictured.
Insert dowels on Backrest Panel(A), Back Support Bar(E) and Front Support Bar(F)
into mountings on Right Panel(C) as pictured above
Attach Right Panel(C) to Backrest Panel(A), Back Support Bar(E) and Front Support
Bar(F) using Bolts(①) with Allen Key(③).
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC 7 of 11

Stand the Chair frame up.
Insert Seat Panel(D) onto Chair frame as shown above.
Attach Seat Panel(D) to Right Panel(C) and Left Panel(B) using Screws(②) with Allen
Key(②).
Note: Insert Screws(②) from inside to outside of Seat Panel(D)
Do not fully tighten the Screws.
Step 5
Noble House Home Furnishings LLC 8 of 11

Step 6
Inspect the Chair and make sure all parts are adequately connected.
Carefully sit onto the Chair. This pressure will help align all parts at all joints.
In a sequential manner, tighten all Bolts and Screws at all joints.
Adjust the Levellers until the Chair is level with the ground.
To adjust the Levellers, get assistance from an adult partner to lift/lean and hold
the Chair while you are working.
Step 7
Adjust Pre-installed Levellers
height for balance
Noble House Home Furnishings LLC 9 of 11

Place Seat Cushion(G), and Back Cushion(H) onto the Chair, and affix the velcro
straps around the Chair as shown above.
Your Armless Chair is ready to be used.
This Armless Chair can only be used on a flat, level surface.
Step 8
With assistance from your adult partners, place the Chairs facedown and connect the
pre-attached clips to connect the Chairs together.
Note: This is an optional step in case you want to connect all the Chairs in the
set together and should be performed before affixing the cushions.
Noble House Home Furnishings LLC 10 of 11

Noble House Home Furnishings LLC 11 of 11