Noble House Home Furnishings ROCKING LOVESEAT User manual

Assembly Instructions
Caution: You must read this before you proceed
ROCKING LOVESEAT
Noble House Home Furnishings LLC
Page 1 of 9
Caution: This Rocking Loveseat is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Rocking Loveseat and to prevent damage to the Rocking Loveseat,
02 persons may be needed to execute this action.

Label Picture Description QTY
A Backrest Panel 1
B Seat Panel 1
C Left Leg Panel 1
D Right Leg Panel 1
E Leg Support Bar 1
Label Picture Description QTY
①
Screw
(M6*80mm) 7
②
Screw
(M6*65mm) 5
③
Allen Key 1
Parts List
Hardware
Noble House Home Furnishings LLC
Page 2 of 9

Before Beginning Assembly:
Assembly Preparation
Noble House Home Furnishings LLC
Page 3 of 9

This Rocking Loveseat has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of the Rocking Loveseat parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
Overview
Assembly Steps
Backrest Panel (A)
Leg Support Bar (E)
Seat Panel (B)
FRONT FACING
Left Leg
Panel (C)
Right Leg
Panel (D)
Noble House Home Furnishings LLC
Page 4 of 9

Step 2
With the help from your assistance, place the Seat Panel (B) with its one side face skywards
onto a clean, soft surface to avoid any scratches or damages to the product.
Align the tenon of Seat Panel (B) into the Mortise of Right Leg Panel (D) as shown above.
Then, affix the Seat Panel (B) with Right Leg Panel (D) by using Screws (①) and Allen Key
(③).
DO NOT FULLY TIGHTHEN SCREWS.
3
1
B
D
Noble House Home Furnishings LLC
Page 5 of 9

Step 3
With the help from your partner, place the assembled part on step 2 to the Left Leg Panel (C)
as shown in picture above.
Align the tenon of Seat Panel (B) into the Mortise of Left Leg Panel (C) as shown above.
Then, affix the Seat Panel (B) with Left Leg Panel (C) by using Screws (①) and Allen Key (③).
Do not fully tighten the Screws.
C
3
1
B
Noble House Home Furnishings LLC
Page 6 of 9

Step 4
Attach the Leg Support Bar (E) to the Right Leg Panel (D) and Left Leg Panel (C) by using
Screws(
①
) with Allen Key(
③
).
You may need to apply a little pressure to enable align the tenon of Leg Support Bar (E) into
the Mortise of Left Leg Panel (C) and Right Leg Panel (D).
Do not fully tighten the Screws.
Step 5
With the help from your partner, turn the finished part in step 5 right side up.
Attach Backrest Panel (A) to Right Leg Panel (D) and Left Leg Panel (C), secure by using
Screw (
②
) and Allen Key (
③)
Do not fully tighten Screws.
2
3
E
1
A
3
D
C
Noble House Home Furnishings LLC
Page 7 of 9

Step 6
Place the Rocking Loveseat on a LEVEL SURFACE.
Inspect the Rocking Loveseat and make sure all parts are connected.
Gently and gracefully, sit into to the Rocking Loveseat.
This would help to align all the parts at all the joint areas.
Then get off the Rocking Loveseat and in a sequential manner, proceed to tighten all Screws.
Whenever moving or lifting the Rocking Loveseat be sure to secure assistance from your adult
partner(s).
When tightening the Bolts and Screws, tighten sequentially.
DO NOT tighten any Bolt or Screw fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and Screws and execute this same process.
WARNING!! IF Rocking Loveseat IS NOT STABLE , IT COULD LEAD TO DAMAGING THE
PRODUCT.
Your Rocking Loveseat is ready for use.
This Rocking Loveseat can only be only be used on a flat, lever surface.
Noble House Home Furnishings LLC
Page 8 of 9

Noble House Home Furnishings LLC
Page 9 of 9