Noble House Home Furnishings Dining Chair Quick start guide

Label Picture Description QTY
A Chair Back 1
B Chair Seat 1
C Front Legs 2
Dining Chair
Caution: You must read this before you proceed.
Noble house Home Furnishings LLC 1 OF 6

Label Picture Description QTY
①
Bolt
(M8*50MM)
6
②
Bolt
(M8*60MM)
5
③Washer 11
④
Spring
Washer
11
⑤Allen Key 1
Before
Beginnin
g
Assembl
y:
Overview
FRONT FACING
Chair Back(A)
Chair Seat(B)
Front legs(C)
Noble house Home Furnishings LLC 2 OF 6

Step 1
Place the Back with Legs(B) on a clean, non-marring surface.
Align the mounting positions on the Seat(A) to the mountings on the Back
with Legs(B).
Lock the middle mounting position first, by using Bolts(①), Spring
Washers(④) and Washers(③) with Allen Key(⑤).
Then lock the corner four mounting positions and attach them using
Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤), as
shown on the picture above.
Frendly notice:
If the mouonting positions cannot be aligned well which hinders the
installation, then sway the Seat(A) lightly when locking the Bolts, this action
could help avoid the Bolts getting stuck and ensure assemble smoothly.
Do not fully tighten the Bolts.
Step 2
This Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Chair parts, the above picture is
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Unpack and place all parts on a clean, non-marring surface.
A
C
B
⑤
②
④
③
Noble house Home Furnishings LLC 3 OF 6

Place the Pack of Seat(A) and Back with legs(B) on the side of a table with
the Seat(A) facing down, as seen in the picture.
Insert Front Leg(C) into the mounting position of Seat(A) and attach using
Bolts(①), Spring Washers(④) and Washers(③) with Allen Key(⑤).
Do not fully tighten the Bolts.
Repeat the same process to attach the remaining one Leg. Attach each leg
using 2 Bolts.
Step 4
Step 3
A
C
B
If wobble
Test again
30CM~50CM
①
④
③
⑤
Noble house Home Furnishings LLC 4 OF 6

Stand the Chair up.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Step 6
Finally, seal the Seat Base Cover back on to the underside of the
chair seat . Turn it the right side up.The chair is ready for use.
Step 5
Place the chair on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the chair to some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the chair freely and vertically with the four legs, hitting the ground, at
the same time.
This Drop Test will help to ensure that all the bolts and gaps to all reach full
alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles found, proceed to tighten all the bolts.
CAUTION : When tightening these bolts, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one.
This would cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same drop tests.
WARNING!! IF CHAIR IS NOT STABLE , IT COULD LEAD TO DAMAGING
THE PRODUCT.
Noble house Home Furnishings LLC 5 OF 6

Noble house Home Furnishings LLC 6 OF 6