Noble House Home Furnishings Chaise Lounge User manual

Assembly Instructions
Caution: You must read this before you proceed
Chaise Lounge
Noble House Home Furnishings LLC Page 1 OF 11

Label Picture Description QTY
A Backrest 1
B Left Armrest 1
C Right Armrest 1
DSeat 1
E Seat Cushion 1
FLeg 4
Part List
Noble House Home Furnishings LLC Page 2 OF 11

Label Picture Description QTY
①Bolt (M8*70 MM) 6
②Washer 6
③Gasket 7
④Allen Key 1
⑤Spring Washer 6
Before Beginning
Assembly:
Hardware
Assembly Preparation
Noble House Home Furnishings LLC Page 3 OF 11

Assembly Steps
This Chaise Lounge has multiple parts and may require up to 60 minutes to assemble. To give you an
overview of the Chaise Lounge parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts and steps
before assembly.
Note: It is recommended that you have an adult partner to assist during the entire assembly
process.
Overview
FRONT FACING
Left Armrest (B)
Right Armrest (C)
Backrest (A)
Seat (D)
Seat Cushion (E)
Leg (F)
Noble House Home Furnishings LLC Page 4 OF 11

Step 1
Open the carton and place all the parts on a clean, non-marring surface.
With the assistance of your partner, slide the Tapered Connectors on the Seat(D) into the Tapered
Connectors on the Left Armrest(B) as shown in the picture.
Repeat the same process with the Right Armrest(C).
Note: Make sure the Tapered Connectors on Left Armrest(B) and Right Armrest(C) lock into the
Tapered Connectors on the Seat(D).
Assistance from an adult partner is needed for this assembly process.
During this assembly process you may need to use your hand to press down and or pave away
the padded surface to facilitate the 'slip and slide' assembly.
Exercise Caution to ensure that your fingers do not get caught or pinched in the assembly
process.
Seat (D)
Seat (D)
Tapered Connectors on
Left Armrest (B)
Tapered Connectors on
Seat (D)
Right Armrest (C)
Left Armrest (B)
Noble House Home Furnishings LLC Page 5 OF 11

Step 2
Push the Seat(D) downwards until it is fully slotted and locked into position in the Armrests.
Fully locked postion: Check and assess that the base of the Armrests(B&C) and Seat(D) are
aligned and level. Assistance from an adult partner is needed for this assembly process.
Right Armrest (C)
Seat (D)
Left Armrest (B)
Noble House Home Furnishings LLC Page 6 OF 11

Step 3
With the assistance from your partner.
Lift the Backrest(A) up, make sure the Backrest(A) is vertical and aligned to the Seat and Armrests.
Align the Tapered Connectors on the Backrest(A) with those on the Left Armrest(B) and Right
Armrest(C).
Your adult partner may need to push the Armrests inwards to the Backrest(A) to allow for better
alignment.
Slip and slide the Backrest, in a gradual and balanced manner into the Tapered Connectors.
Push the Backrest(A) downwards until it is fully slotted.
Note: Make sure the Tapered Connectors on the Backrest(A) lock into the Tapered Connectors on
Left Armrest(B) and Right Armrest(C).
Fully locked postion: Check and assess that the base of the Armrests(B&C) and Seat(D) are
aligned and level. Assistance from an adult partner is needed for this assembly process.
Right Armrest (C)
Left Armrest (B)
Seat (D)
Tapered
Connectors
on Backrest
Tapered
Connectors
on Armrest
Backrest (A)
Noble House Home Furnishings LLC Page 7 OF 11

Tilt and lay the Chaise Lounge on its Backrest(A) onto a flat surface.
Attach Seat(D) to Left Armrest(B) and Right Armrest(C) using Bolts(①), Spring Washers(⑤), and
Washers(②) with Allen Key(④).
Then attach Seat(D) to Backrest(A) using Bolts(①), Spring Washers(⑤), and Washers(②) with Allen
Key(④) as pictured above.
Tighten the Bolts fully in a sequential manner.
DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather, In a sequential manner, gradually tighten each Bolt until all Bolts are evenly secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Note: If you can not insert the Bolts into position, please back to Step 3 to "push Backrest
downwards".
Step 4
Left Armrest (B)
Right Armrest (C)
Seat (D)
Noble House Home Furnishings LLC Page 8 OF 11

Install the Leg(F) at the bottom of the Chaise by placing one Gasket(③) on the threaded stem.
Then insert threaded stem into the threaded mounting postion at the corner of the Chaise Lounge.
Tighten by turning the Leg clockwise.
Repeat the same step to install the remaining three Legs.
Note: The use of Gaskets are OPTIONAL and are especially useful to help alleviate slight wobbles.
Some Legs may need more than one whilst some legs may not need any.
Step 5
Gasket (③)
Left Armrest (B)
Right Armrest (C)
Seat (D)
Use Gasket(③) to achieve stability
Noble House Home Furnishings LLC Page 9 OF 11

Place the Seat Cushion(E) onto the Chaise Lounge.
Your Chaise Lounge is ready for use.
This Chaise Lounge can only be used on a flat, level surface.
Step 6
Seat Cushion (E)
Noble House Home Furnishings LLC Page 10 OF 11

Noble House Home Furnishings LLC Page 11 OF 11