Nokia CR-96 User manual

Nokia Holder Easy Mount HH-12
& Nokia Mobile Holder CR-96
Issue 1

5
6
89
10
7

© 2008 Nokia. All rights reserved. 3
Englsih
© 200 Nokia. All rights reserved. Nokia and Nokia Connecting People are
registered trademarks of Nokia
Corporation.
Introduction
The Nokia Holder Easy Mount
HH-12 is a mounting device that
allows you to attach your
compatible Nokia mobile holder to
the windscreen of your vehicle.
To use the mounting device with
your compatible mobile holder,
attach the mounting device to the
windscreen, adjust the mounting
device into the desired position,
and attach your mobile holder to
the mounting device.
Keep all accessories and
enhancements out of the reach of
small children.
General safety instructions
Obey all local laws. Always keep
your hands free to operate the
vehicle while driving. Your first
consideration while driving should
be road safety. Only operate the
mounting device or mobile holder
if it is safe to do so under all
driving conditions.
When you install the mounting
device or mobile holder, ensure
that they do not interfere with or
hinder the steering or braking
systems or other systems used in
8

4
4 © 2008 Nokia. All rights reserved.
the operation of the vehicle (for
example, airbags) or disturb your
field of vision while driving.
Check that the deployment of the
airbag is not blocked or impaired
in any way.
Ensure that the mounting device
or mobile holder is not installed
where you might come in contact
with it in the event of an accident
or collision.
Periodically check that the suction
cup at the bottom of the mounting
device is firmly attached to the
windscreen, especially if the
ambient temperature changes a
lot.
Never leave the mounting device
inside the vehicle in direct
sunlight or in excessive heat. The
mounting device and suction cup
may be damaged and adhesion
may be impaired if the inside
temperature exceeds +70°C
(160°F).
Attach to a windscreen
Locate a safe mounting surface on
the windscreen, and clean the
surface thoroughly with a glass
cleaner and a clean towel. If the
ambient temperature is below
+15°C (60°F), carefully warm the
surface and the suction cup with a
hair dryer to ensure a firm grip on
the windscreen. Ensure that you
do not heat the windscreen
excessively to avoid damage to it.
Press the suction cup at the
bottom of the mounting device
firmly on the windscreen (see step

© 2008 Nokia. All rights reserved. 5
Englsih
1 at the start of this guide), and
carefully push the locking lever
inside the mounting device (2)
towards the suction cup to create
a vacuum between the suction cup
and the windscreen. Check that
the suction cup is firmly attached.
To detach the mounting device
from the windscreen, carefully
push the locking lever toward the
top of the mounting device (3),
and pull the strap located on the
edge of the suction cup (4).
Set to the desired position
Do not adjust the mounting device
while driving.
To set the top of the mounting
device to the desired position,
loosen the two screws in the
middle of the mounting device,
turn the top to the desired
position, and tighten the screws
(5). Ensure that the top of the
device is firmly locked into place.
To set the mounting plate at the
top of the mounting device to the
desired position, loosen the screw
below the plate, turn the plate to
the desired position, and tighten
the screw (6).
Mount the mobile holder
To attach a compatible Nokia
mobile holder to the mounting
plate, use the screw supplied with
the holder.

6
6 © 2008 Nokia. All rights reserved.
To use the CR-96 mobile holder,
remove the protection plate with
the Nokia text from the holder,
attach the holder to the mounting
plate with the supplied screw, and
replace the protection plate (7). To
insert your mobile device into the
holder, slide it into the holder from
the top (8). To remove the device,
push the catch at the top of the
holder (9), and pull the device out
(10).
When attaching a mobile holder,
ensure that the display of the
mobile device is clearly visible for
the user. For your safety, install the
holder in the upright position.
Care and maintenance
Your device is a product of superior
design and craftsmanship and should
be treated with care. The following
suggestions will help you protect
your warranty coverage.
• Do not use or store the device in
dusty, dirty areas. Its moving parts
can be damaged.
• Do not drop, knock, or shake the
device. Rough handling can break
fine mechanics.
• Do not use harsh chemicals,
cleaning solvents, or strong
detergents to clean the device.
• Do not paint the device. Paint can
clog the moving parts and prevent
proper operation.
If the product is not working properly,
take it to the nearest authorised
service facility for service.