Nokia CR-114 User manual

Nokia Holder Easy Mount
HH-20 and CR-114/115
Issue 2.0
1
E
B
A
DC

A
B
C
D
2
G
E
F
3
4

7
9
8
5
6

ENGLISH
© 2010 Nokia. All rights reserved.
Nokia, Nokia Connecting People and the
Nokia Original Accessories logo are
trademarks or registered trademarks of
Nokia Corporation.
Introduction
The Nokia Holder Easy Mount HH-20
is a mounting device that allows you
to attach your compatible mobile
holder to the windscreen or, using the
optional adhesive pad, to the
dashboard of your car.
Read this guide carefully before
installing and using the product.
This product may contain small parts.
Keep them out of the reach of small
children.
General safety instructions
Obey all local laws. Always keep your
hands free to operate the car while
driving. Your first consideration while
driving should be road safety. Only
operate the mounting device or
mobile holder if it is safe to do so
under all driving conditions.
When you install the mounting device
or mobile holder, make sure they do
not interfere with or hinder the
steering or braking systems or other
systems used in the operation of the
car (for example, airbags) or disturb
your field of vision while driving.
Check that the deployment of the
airbag is not blocked or impaired in
any way.

ENGLISH
Make sure the mounting device or
mobile holder is not installed where
you might come in contact with it in
the event of an accident or collision.
Periodically check that the suction cup
at the bottom of the mounting device
is firmly attached to the windscreen or
dashboard, especially if the ambient
temperature changes a lot.
Never leave the mounting device
inside the car in direct sunlight or in
excessive heat. The mounting device
and suction cup may be damaged and
adhesion may be impaired if the inside
temperature exceeds +70°C (160°F).
When attaching a mobile holder, make
sure the display of the mobile device is
clearly visible for the user. For your
safety, install the holder in the upright
position.
Attach to a windscreen
Attach the holder to the
mounting device
To attach the mobile holder to the
mounting device, insert the catch on
the mounting device into the slot at
the back of the holder (see step 1A at
the start of this guide). Rotate the
holder clockwise about 90 degrees
until it locks into place (1B).
To detach the holder from the
mounting device, rotate it
anticlockwise.
Attach the mounting device to
the windscreen
Before you attach the mounting
device to the windscreen, locate a safe
mounting surface on the windscreen,

ENGLISH
and clean the surface thoroughly with
a glass cleaner and a clean towel. If
the ambient temperature is below
+15°C (60°F), carefully warm the
surface and the suction cup with a
hair dryer to ensure a firm grip on the
windscreen. Make sure you do not
heat the windscreen excessively to
avoid damage to it.
Press the suction cup of the mounting
device against the windscreen (1C),
and rotate the ring on the mounting
device clockwise (1D) to create a
vacuum between the suction cup and
the windscreen. Make sure the
mounting device is firmly attached
(1E).
To detach the suction cup from the
windscreen, rotate the ring on the
mounting device anticlockwise (7),
pull the strap located on the edge of
the suction cup (8), and pull the holder
with the mounting device from the
windscreen (9).
Attach to a dashboard
Attach the mounting device to
the dashboard
If the product was supplied with an
adhesive pad, you can attach the
mounting device to the dashboard.
Make sure the surface where you
attach the adhesive pad on the
dashboard is flat, dry, and free from
dirt and dust.
Peel off the protective sheet from the
adhesive side of the pad (see step 2A),
and press the pad against the
dashboard so that it stays firmly in
place. When you peel off the

ENGLISH
protective sheet from the pad, do not
touch the adhesive side.
Press the suction cup of the mounting
device against the pad (2B). Turn the
catch on the mounting device to the
desired position (2C). Rotate the ring
on the mounting device clockwise
(2D) to create a vacuum between the
suction cup and the pad.
To detach the suction cup from the
pad, proceed in the same way as when
you detach the cup from a windscreen
(7, 8, and 9).
Attach the holder to the
mounting device
To attach the mobile holder to the
mounting device, insert the catch on
the mounting device into the slot at
the back of the holder (2E). Rotate the
holder clockwise about 90 degrees
until it locks into place (2F). Make sure
the mounting device is firmly
attached (2G).
To detach the holder from the
mounting device, rotate it
anticlockwise.
Place or remove the mobile device
Do not place or remove a mobile
device while driving.
To place your device into the holder,
insert the device into the holder (3),
hold the device, and push the arm (4)
to lock the device firmly in place. To
charge the battery of your device, use
a compatible charger.
To remove the device, hold the device
to prevent it from dropping, push the
release button (5), and pull the device
out from the holder (6).

ENGLISH
Taking care of your device
Your device is a product of superior
design and craftsmanship and should be
treated with care. The following
suggestions will help you protect your
warranty coverage.
• Do not use or store the device in
dusty, dirty areas. Its moving parts
can be damaged.
• Do not drop, knock, or shake the
device. Rough handling can break fine
mechanics.
• Do not use harsh chemicals, cleaning
solvents, or strong detergents to
clean the device. Only use a soft,
clean, dry cloth to clean the surface of
the device.
• Do not paint the device. Paint can
clog the moving parts and prevent
proper operation.