Nokia RM-94 Mounting instructions

Issue 1 04/2005 COMPANY CONFIDENTIAL
Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care
3 - Service Software and
Tuning Instructions

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
2 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
[This page intentionally blank]

Issue 1 04/2005 COMPANY CONFIDENTIAL 3
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Table of Contents Page No
Quick Guide for Phoenix Service SW Installation............................................ 5
Phoenix Installation Steps in Brief.................................................................... 6
Phoenix Service SW............................................................................................ 7
Before installation............................................................................................... 7
Installing Phoenix............................................................................................... 8
Updating Phoenix installation........................................................................... 12
Uninstalling Phoenix......................................................................................... 13
Repair............................................................................................................... 15
Data Package for Phoenix (Product Specific) ................................................ 17
Before installation............................................................................................. 17
Installing Phoenix data package (product specific).......................................... 17
Uninstalling the data package.......................................................................... 21
Configuring Users............................................................................................. 22
Managing Connections..................................................................................... 24
Updating Flash Support Files for FPS-8* and FLS-4*.................................... 27
Before installation ............................................................................................ 27
Installing the flash support files (only separate installation package) .............. 27
Updating FPS-8* flash prommer SW ............................................................... 30
Activating and Deactivating FPS-8.................................................................. 33
Activating FPS-8.............................................................................................. 33
Deactivating FPS-8.......................................................................................... 34
JBV-1 Docking Station SW............................................................................... 35
Before installation ............................................................................................ 35
Installing SW needed for the JBV-1 SW update.............................................. 35
Baseband Calibration ....................................................................................... 41
General instructions for tuning......................................................................... 41
UEMEK calibration........................................................................................... 41
Calibration limits ............................................................................................. 43
Phoenix Tuning ................................................................................................. 44
General instructions for tuning......................................................................... 44
RF tuning after repairs..................................................................................... 44
Semi-automatic calibrations and measurements - step by step: RX/TX and GSM
bands ................................................................................................................. 45
RX tunings ..................................................................................................... 45
RX band filter response compensation .......................................................... 48

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
4 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
RX channel select filter calibration ................................................................. 51
TX power level tuning .................................................................................... 52
TX I/Q tuning .................................................................................................. 58
Fully automatic calibration, tuning & measurement by Phoenix <Auto-Tune> 63
Preparations for Phoenix ............................................................................... 64
Automatic tuning procedure ........................................................................... 66

Issue 1 04/2005 COMPANY CONFIDENTIAL 5
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Quick Guide for Phoenix Service SW Installation

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
6 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
Phoenix Installation Steps in Brief
DCT-4 generation Test and Service Software is called “Phoenix”.
These are the basic steps to install Phoenix:
• Connect a DK2 Dongle or FLS-4S POS Flash Device.
• Install the Phoenix Service SW.
• Install the Data Package for Phoenix.
• Configure users.
• Manage connection settings (depends on the tools you are using).
Phoenix is now ready for FLS-4S Point Of Sales Flash Device use.
If you use FPS-8:
• Update FPS-8 SW.
• Activate FPS-8.
• Update JBV-1 Docking Station SW (only when needed).
Phoenix is now ready to be used also with FPS-8 flash prommer and other tools.
The Phoenix Service Software installation contains:
• service software support for all phone models included in the package
• flash update package files for FPS-8* and FLS-4S programming devices
• all needed drivers for: DK2 dongle
FLS-4S point of sales flash device
USB devices
Separate installation packages for flash update files and drivers are also available, but it is not
necessary to use them unless updates appear between Phoenix Service SW releases. If sep-
arate update packages are used, they should be used after Phoenix and data packages have
been installed.
The phone model specific data package includes all changing product specific data:
• product software Binary files
• files for type label printing
• validation file for the Faultlog repair data reporting system
• all product specific configuration files for Phoenix software components
Please refer to Service Manual and Technical Bulletins for more information concerning phone
model specific service tools and equipment setup.
Phoenix Service SW and phone data packages should only be used as complete installation
packages. Uninstallation should be made from Windows Control Panel.

Issue 1 04/2005 COMPANY CONFIDENTIAL 7
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Phoenix Service SW
■ Before installation
• Check that a dongle is attached to the parallel port of your computer .
• Download the installation package (e.g. phoenix_service_sw_2004_46_4_75.exe)
to your computer (e.g. C:\TEMP).
• Close all other programs.
• Run the application file (e.g. phoenix_service_sw_2004_46_4_75.exe) and follow
instructions on the screen.
Administrator rights may be required to be able to install Phoenix depending on the Operating
System
If uninstalling orrebooting is needed at any point, you will be prompted by the Install Shield pro-
gram.
If at any point during installation you get this message, the dongle is not found and installation
cannot continue.
Possible reasons may be defective or too old PKD-1Dongle (five digit serial number dongle
when used with FPS-8 Prommer) or that the FLS-4S POS Flash Dongle is defective or power
to it is not supplied by external charger.
First, check the COM /parallel ports used! After correcting the problem, the installation can be
restarted.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
8 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
■ Installing Phoenix
Run the phoenix_service_sw_2004_46_4_75.exe to start the installation. Install Shield will pre-
pare.
To continue, click "Next" in the Welcome dialog.
Choose the destination folder, it is recommended to use the default folder C:\Program-
Files\Nokia\Phoenix.
2004_46_4_75

Issue 1 04/2005 COMPANY CONFIDENTIAL 9
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Choose “Next” to continue. You may choose another location by selecting “Browse” (not rec-
ommended).
Setup copies the components, progress of the setup is shown. Please wait…
Drivers are installed and updated, please wait. The process may take several minutes to com-
plete.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
10 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
If the operating system does not require rebooting (Windows 2000, XP), the PC compo-
nents are registered straight away.

Issue 1 04/2005 COMPANY CONFIDENTIAL 11
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Click "Finish" to finalize. Phoenix is ready for use.
If the operating system used requires restarting your computer (Windows 98, SE, ME),
the Install Shield Wizard notifies you about it. Select "Yes..." to reboot the PC immediately and
"No..." to reboot the PC manually afterwards.
After the reboot components are registered and Phoenix is ready for use. Note that Phoenix
doesn't work, if components are not registered.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
12 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
Now the installation of Phoenix Service SW is ready and it can be used after:
• installing phone model specific Phone Data Package for Phoenix
• configuring users and connections
FLS-4S can be used right away.
FPS-8* can be used after updating Flash Update Package files to it .
■ Updating Phoenix installation
If you already have the Phoenix Service SW installed on your computer, sooner or later there
will be need to update it when new versions are released.
Always use the latest available versions of both the Phoenix Service SW and the Phone Spe-
cific Data Package. Instructions can be found in phone model specific Technical Bulletins and
Phone Data package readme.txt files (shown during installation).
To update Phoenix, you need to take exactly the same steps as when installing it for the first
time.
• Download the installation package to your computer hard disk.
• Close all other programs.
• Run the application file (e.g. phoenix_service_sw_2004_46_4_75.exe).
A newer version of Phoenix will be installed.
Driver versions will be checked and if need be, updated.
When you update Phoenix from an old to a new version (e.g. a11_2003_41_5_28 to
a12_2003_50_6_35 ), the update will take place automatically without uninstallation.
If you try to update Phoenix with the same version that you already have (e.g. 2004_46_4_75 to
2004_46_4_75), you are asked if you want to uninstall the version of Phoenix you have on your
PC. In this case, you can choose between total uninstallation and repair, just like when you
choose to uninstall Phoenix service software from the Windows control panel.
If you try to install an older version (e.g. downgrade from 2004_46_4_75 to
a11_2003_41_5_28) the installation will be interrupted.

Issue 1 04/2005 COMPANY CONFIDENTIAL 13
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Please always follow the instructions on the screen.
■ Uninstalling Phoenix
Uninstallation can be done manually from Windows Control Panel - Add / Remove Programs.
Choose “Phoenix Service Software” and click "Add/Remove".
Choose “Remove” to uninstall Phoenix.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
14 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
Progress of the uninstallation is shown.
If the operating system does not require rebooting, select “Finish” to complete.
If the operating system requires rebooting, Install Shield Wizard notifies you about it. Select
"Yes..." to reboot the PC immediately and "No..." to reboot the PC manually afterwards.

Issue 1 04/2005 COMPANY CONFIDENTIAL 15
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
■ Repair
If you experience any problems with the service software or suspect that files have been lost,
you can use the repair function before completely reinstalling Phoenix. Note that the original
installation package (e.g. phoenix_service_sw_2004_46_4_75.exe)must be found on your PC
when you run the repair setup.
Run Windows Control Panel - Add / Remove Programs, choose “Phoenix Service Software”.
Click "Add/Remove". In the following view, choose “Repair”.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
16 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
Phoenix reinstalls the required components and registers them, the procedure is the same as
in the update installation.
To complete, choose “Finish” .

Issue 1 04/2005 COMPANY CONFIDENTIAL 17
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
Data Package for Phoenix (Product Specific)
■ Before installation
Product Data Package contains all product specific data to make the Phoenix Service Software
and tools usable with a certain phone model.
Check that the dongle is attached to the parallel port of your computer.
Install Phoenix Service SW.
Download the installation package (e.g. RM-94_dp_v_0.00_mcuO0.00.0.exe)to your computer
(e.g. C:\TEMP)
Close all other programs.
Run the application file (e.g. RM-94_dp_v_0.00_mcuO0.00.0.exe )and follow the instructions on
the screen.
Please note that very often the Phoenix Service SW and the Phone Specific Data Package for
Phoenix come in pairs, meaning that certain version of Phoenix can only be used with certain
version of Data Package. Always use the latest available versions of both. Instructions can be
found in phone model specific Technical Bulletins and readme.txt files of the data packages.
■ Installing Phoenix data package (product specific)
Run the RM-94_dp_v_0.00_mcuO0.00.0.exe to start installation.
Choose “Next”. The files needed for installation will be extracted. Please wait.

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
18 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
To continue, choose “Next”.
In this view, you can see the contents of the data package. Read the text carefully. There
should be information about the Phoenix version needed with this data package. Choose
“Next”.

Issue 1 04/2005 COMPANY CONFIDENTIAL 19
Copyright © 2005 Nokia. All Rights Reserved.
RM-94
3 - Service Software and Tuning Instructions Nokia Customer Care
To continue, confirm the location and choose “Next” . Install shield checks where the Phoenix
application is installed and the directory is shown. Choose “Next” to continue.
To start copying the files, choose “Next”..

RM-94
Nokia Customer Care 3 - Service Software and Tuning Instructions
20 COMPANY CONFIDENTIAL Issue 1 04/2005
Copyright © 2005 Nokia. All Rights Reserved.
Phone model specific files are installed. Please wait.
To complete installation, choose “Finish”.
You now have all phone model specific files installed in your Phoenix service SW.