Nokia BH-108 User manual

© 2010 Nokia. All rights reserved.
Nokia Bluetooth Headset BH-108
9220726
Issue 1.0
8
2
7
1
4
3
5
6
9

2
2 © 2010 Nokia. All rights reserved.
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares
that this BH-108 product is in
compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC. A
copy of the Declaration of Conformity
can be found at
http://www.nokia.com/phones/
declaration_of_conformity/.
© 2010 Nokia. All rights reserved.
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
Introduction
With the Nokia Bluetooth Headset
BH-108, you can make and answer
calls hands-free with your
compatible mobile device.
Read this user guide carefully
before using the headset. Also,
read the user guide for the device
that you connect to the headset.
The surface of this device is
nickel-free.
Bluetooth wireless
technology
The headset is compliant with
Bluetooth Specification 2.0 + EDR
supporting the Headset Profile 1.1
and Hands-Free Profile 1.5. Check
with the manufacturers of other
devices to determine their
compatibility with this device.

© 2010 Nokia. All rights reserved. 3
Get started
The headset contains the
following parts shown on the title
page: earpiece (1), indicator light
(2), multifunction key (3), earloop
(4), charger connector (5), and
microphone (6).
Before using the headset, you
must charge the battery and pair
the headset with a compatible
device.
Compatible chargers
This device is intended for use
when supplied with power from the
following chargers: AC-3, AC-4,
AC-5, AC-8, DC-4, and DC-9. The
exact charger model number may
vary depending on the type of
plug. The plug variant is identified
by one of the following: E, EB, X,
AR, U, A, C, K, B, or UB.
Charge the battery
1. Connect the charger to a wall
outlet.
2. Connect the charger cable to
the charger connector. The red
indicator light is displayed
during charging. Charging the
battery fully may take up to
2 hours.
3. When the battery is fully
charged, the green indicator
light is displayed. Disconnect
the charger from the headset,
then from the wall outlet.
The fully charged battery has
power for up to 5 hours of talk
time or up to 120 hours of standby
time.

4
4 © 2010 Nokia. All rights reserved.
To check the battery charge when
the headset is not connected to a
charger, press the multifunction
key when the headset is
connected to a mobile device. If
the indicator light is green, the
charge level is sufficient. If the
light is yellow, you may need to
recharge the battery soon. If the
light is red, recharge the battery.
When the battery charge is low,
the headset beeps every 5 minutes
and the red indicator light flashes.
Switch on or off
To switch on, press and hold the
multifunction key for about 2
seconds. The headset beeps, and
the green indicator light is
displayed. The headset tries to
connect to the last used device.
When the headset is connected to a
device and is ready for use, the
green indicator light flashes slowly.
If the headset has not been paired
with a device, it automatically
enters pairing mode.
To switch off, press and hold the
multifunction key for about 5
seconds. The headset beeps, and
the red indicator light is briefly
displayed. If the headset is not
connected to a device within
about 30 minutes, it switches off
automatically.
Pair and connect the headset
Before using the headset, you
must pair and connect it to a
compatible device.
You can pair the headset with up
to eight devices, but you can
connect it to only one device at a
time.
1. Make sure your mobile device is
switched on and the headset is
off.

© 2010 Nokia. All rights reserved. 5
2. If the headset has not been
previously paired with a device,
switch on the headset. The
headset enters pairing mode,
and the green indicator light
starts to flash quickly.
If the headset has been
previously paired with a device,
make sure the headset is
switched off, and press and
hold the multifunction key for
about 5 seconds until the green
indicator light starts to flash
quickly.
3. Within about 3 minutes,
activate the Bluetooth feature
on your device, and set it to
search for Bluetooth devices.
For details, see the user guide
of your mobile device.
4. Select the headset from the list
of found devices.
5. Enter the passcode 0000 to
pair and connect the headset to
your device. In some devices,
you may need to make the
connection separately after
pairing.
When the headset is connected to
your device and is ready for use,
the green indicator light flashes
slowly.
To manually connect the headset
to the last used device, press and
hold the multifunction key for
about 2 seconds, or make the
connection in the Bluetooth menu
of your device.
You may be able to set your device
so that the headset connects to it
automatically. To activate this
feature in a Nokia device, modify
the paired device settings in the
Bluetooth menu.

6
6 © 2010 Nokia. All rights reserved.
Basic use
Place the headset on the ear
The headset is ready to be used on
the right ear. To use the headset on
the left ear, attach the earloop to
the headset so that it is to the left
of the Nokia logo (9).
Slide the earloop behind your ear
(7), and gently push the earpiece
against your ear. Push or pull the
earloop to set its length. Point the
headset towards your mouth (8).
Calls
To make a call, use your mobile
device in the normal way when the
headset is connected to it.
To redial the number you last
called (if your mobile device
supports this feature with the
headset), when no call is in
progress, press the multifunction
key twice.
To activate voice dialling (if your
mobile device supports this
feature with the headset), when
no call is in progress, press and
hold the multifunction key for
about 2 seconds. Proceed as
described in the user guide of the
mobile device.
To answer or end a call, press the
multifunction key. To reject a call,
press this key twice.
To adjust the volume, use the
volume controls on the connected
device.
To switch a call from the headset
to a compatible device, press and
hold the multifunction key for
about 2 seconds, or switch off the

© 2010 Nokia. All rights reserved. 7
headset. To switch the call back to
the headset, press and hold the
multifunction key for about 2
seconds, or switch on the headset.
Clear settings or reset
To clear all the settings from the
headset, switch off the headset,
and press and hold the
multifunction key for about 8
seconds. The headset beeps twice,
and the red and green indicator
lights alternate. After the settings
are cleared, the headset enters
pairing mode.
To reset the headset if it stops
functioning, even though it is
charged, connect the headset to a
charger while you press and hold
the multifunction key.
Troubleshooting
If you cannot connect the headset
to your compatible device, make
sure the headset is charged,
switched on, and paired with your
device.