Nokia BH-607 User manual

Nokia Bluetooth Headset BH-607
9218881/1.1
10
11
1
3
2
8
7
6
9
4
5
9218881_EN-US_1.fm Page 1 Wednesday, November 25, 2009 8:37 PM

12
14
13
9218881_EN-US_1.fm Page 2 Friday, September 11, 2009 6:01 PM

ENGLISH
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares that
this BH-607 product is in compliance with
the essential requirements and other
relevant provisions of Directive 1999/5/EC.
A copy of the Declaration of Conformity can
be found at http://www.nokia.com/phones/
declaration_of_conformity/.
© 2009 Nokia. All rights reserved.
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
Introduction
With the Nokia Bluetooth Headset
BH-607, you can make and answer
calls hands-free with your compatible
mobile device. The headset is provided
with wind noise reduction and noise
cancellation that helps you handle
calls in noisy environments.
Read this user guide carefully before
using the headset. Also, read the user
guide for the device that you connect
to the headset.
Note: The surface of this
device does not contain
nickel in the platings.
The surface of this device contains
stainless steel.
My own key
The headset has a shortcut key that
you can set to perform different
functions on a compatible Nokia
device using the Nokia Accessory
Setup Application.
With the application, you can also
view headset information and define
headset settings when the headset is
connected to your device. For details,
9218881_EN-US_1.fm Page 3 Friday, September 11, 2009 6:01 PM

ENGLISH
read the built-in help of the
application.
If the application is not already
installed in your mobile device, check
the availability of the application for
your device from the support pages
of this headset at www.nokia.com/
support or your local Nokia website.
If the application is not available for
your Nokia device, you can use the
shortcut key to mute the microphone
during a call.
Bluetooth compatibility
The headset is compliant with the
Bluetooth Specification 2.1 + EDR
supporting the Headset Profile 1.1 and
Hands-Free Profile 1.5. Check with the
manufacturers of other devices to
determine their compatibility with
this device.
Get started
The headset contains the following
parts shown on the title page:
power key (1), volume key (2), My own
key (3), answer/end key (4),
microphones (5), indicator light (6),
charger connector (7), earloop (8),
and earpiece (9).
Before using the headset, you must
charge the battery and pair the
headset with a compatible device.
Compatible chargers
This device is intended for use when
supplied with power from the
following chargers: AC-3, AC-4, AC-5,
and DC-4. The exact charger model
number may vary depending on the
type of plug. The plug variant is
identified by one of the following:
E, EB, X, AR, U, A, C, or UB.
9218881_EN-US_1.fm Page 4 Friday, September 11, 2009 6:01 PM

ENGLISH
Charge the battery
1. Connect the charger to a wall
outlet.
2. Connect the charger cable to the
charger connector. The red
indicator light is displayed during
charging.
Charging the battery fully may take
up to 1 hour. Charging the battery
with the AC-5 charger for
15 minutes provides up to 5 hours
of talk time.
3. When the battery is fully charged,
the green indicator light is
displayed. Disconnect the charger
from the headset, then from the
wall outlet.
The fully charged battery has power
for up to 7 hours of talk time or up to
160 hours of standby time.
To check the battery charge when the
headset is not connected to a charger,
press the power key when the headset
is connected to a mobile device. If the
indicator light is green, the charge
level is sufficient. If the light is yellow,
you may need to recharge the battery
soon. If the light is red, recharge
the battery.
When the battery charge is low, the
headset beeps every 5 minutes and
the red indicator light flashes.
Switch on or off
To switch on, press and hold the power
key for about 2 seconds. The headset
beeps, and the green indicator light
flashes slowly while the headset tries
to connect to one or two last
connected devices. When the headset
is connected to at least one device and
is ready for use, the blue indicator
light flashes slowly. If the headset has
not been paired with a device, it
automatically enters pairing mode.
9218881_EN-US_1.fm Page 5 Friday, September 11, 2009 6:01 PM

ENGLISH
To switch off, press and hold the
power key for about 2 seconds. The
headset beeps, and the red indicator
light is briefly displayed. If the headset
is not connected to a device within
about 30 minutes, it switches off
automatically.
Pair and connect the headset
Before using the headset, you must
pair and connect it to a compatible
device.
You can pair the headset with up to
eight devices, but you can connect it
to only up to two devices at a time.
1. Ensure that your mobile device is
switched on and the headset is off.
2. If the headset has not been
previously paired with a device,
switch on the headset. The headset
enters pairing mode, and the blue
indicator light starts to flash
quickly.
If the headset has been previously
paired with a device, ensure that
the headset is switched off, and
press and hold the power key for
about 5 seconds until the blue
indicator light starts to flash
quickly.
3. Within about 3 minutes, activate
the Bluetooth feature on your
device, and set it to search for
Bluetooth devices. For details, see
the user guide of your mobile
device.
4. Select the headset from the list of
found devices.
5. If necessary, enter the passcode
0000 to pair and connect the
headset to your device.
In some devices, you may need to
make the connection separately
after pairing.
9218881_EN-US_1.fm Page 6 Friday, September 11, 2009 6:01 PM

ENGLISH
When the headset is connected to at
least one device and is ready for use,
the blue indicator light flashes slowly.
To manually connect the headset to
one or two last used devices, press and
hold the answer/end key for about
2 seconds (when no devices are
connected), or make the connection in
the Bluetooth menu of the desired
device. If you have a device connected
to the headset and want to connect
a second device, make the connection
in the Bluetooth menu of the device.
You may be able to set your device so
that the headset connects to it
automatically. To activate this feature
in a Nokia device, change the paired
device settings in the Bluetooth menu.
Basic use
Change the earpad
The headset may be provided with
different sized earpads. Select the
earpad that fits the best and is the
most comfortable for your ear.
To change the earpad, pull the current
earpad from the earpiece, and push
the new earpad into place (13).
Place the headset on the ear
Gently push the earpiece against
your ear.
You can rotate the earpad to keep the
headset securely in the ear (14). For
example, if you use the headset on the
right ear, you may need to rotate the
earpad to the right for the best fit. If
you wear an earring, ensure that it is
not accidentally attached to the
earpad.
9218881_EN-US_1.fm Page 7 Friday, September 11, 2009 6:01 PM

ENGLISH
To use the headset with the earloop,
attach the earloop to it (12). To detach
the earloop, gently pull it from the
headset. Slide the earloop behind your
ear (10), and point the headset toward
your mouth (11). Push or pull the
earloop to set its length.
Adjust volume
The headset automatically adjusts the
volume according to ambient noise. To
manually adjust the volume, slide the
volume key up or down. To adjust the
volume quickly, slide and hold the key.
The selected volume level is saved for
the device that you currently use with
the headset.
Calls
To make a call, use your mobile device
in the normal way when the headset is
connected to it.
To redial the number you last called
(if your mobile device supports this
feature with the headset), when no
call is in progress, press the answer/
end key twice.
To activate voice dialing (if your
mobile device supports this feature
with the headset), when no call is in
progress, press and hold the answer/
end key for about 2 seconds. Proceed
as described in the user guide of the
mobile device.
To answer or end a call, press the
answer/end key. To reject a call, press
this key twice.
To mute or unmute the microphone
during a call, press the volume key. The
headset beeps, and a related icon is
displayed on your device (if supported
by the device).
To switch a call between the headset
and a compatible connected device,
press and hold the answer/end key for
about 2 seconds.
9218881_EN-US_1.fm Page 8 Friday, September 11, 2009 6:01 PM

ENGLISH
Manage two calls
To manage two calls at the same time,
your mobile device must support the
Bluetooth Hands-Free Profile 1.5, and
call waiting must be activated in the
device. Call waiting is a network
service and is available when the
headset is connected to only one
device.
To answer a waiting call and end the
active call, press the answer/end key.
To answer a waiting call and put the
active call on hold, press and hold the
answer/end key for about 2 seconds.
To end the active call and make the
call on hold active, press the answer/
end key.
To switch between the active call and
the call on hold, press and hold the
answer/end key for about 2 seconds.
Turn lights on or off
By default, the indicator lights are
shown in all situations. To turn the
lights off in some situations (for
example, during a call or when the
headset is connected to a cell phone)
or back on, press and hold the answer/
end key and the volume key for about
5 seconds when the headset is
connected to a device. The yellow
indicator light flashes once.
To turn the lights back on, press and
hold the answer/end key, and slide and
hold the volume key up for about
5 seconds. The yellow indicator light
flashes once.
Allow connection to two
devices
You can have the headset connected
to two devices at the same time.
By default, the headset can only be
connected to one device at a time.
9218881_EN-US_1.fm Page 9 Friday, September 11, 2009 6:01 PM

ENGLISH
To allow the headset to connect to
two devices, switch off the headset,
and press and hold the power key, and
slide and hold the volume key up for
about 5 seconds. The green indicator
light flashes once.
To allow the headset to connect to
two devices, switch off the headset,
and press and hold the power key, and
slide and hold the volume key up for
about 5 seconds. The yellow indicator
light flashes once.
If the headset can connect to two
devices at the same time and you use
redialing or voice dialing, the call is
made on the device that you last used
to make a call when the headset was
connected to it.
Clear settings or reset
To clear all the settings from the
headset (including settings you have
defined with the Nokia Accessory
Setup Application), switch off the
headset, and press and hold the power
key and the answer/end key at the
same time for about 8 seconds. The
headset beeps twice, and the red and
green indicator lights alternate. After
the settings are cleared, the headset
enters pairing mode.
To reset the headset if it stops
functioning, even though it is charged,
connect the headset to a charger
while you press and hold the
power key.
Troubleshooting
If you cannot connect the headset to
your compatible device, check that
the headset is charged, switched on,
and paired with the device.
9218881_EN-US_1.fm Page 10 Friday, September 11, 2009 6:01 PM