Norac UC5 Topcon X30 User manual

A
GCO América do Sul
(Factory Install)
Installation Manual
SP01

Printed in Canada
Copyright 2010 by NORAC Systems International Inc.
Reorder P/N: UC5-BC-SP01-INST Rev G (AGCO Brazil Factory Install)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

Contents
1Introduction................................................................................................................. 1
2Technical Specifications ............................................................................................. 2
3General UC5 System Layout..................................................................................... 3
4Kit Parts ....................................................................................................................... 4
5Ultrasonic Sensor Installation ................................................................................... 7
6Roll Sensor Installation............................................................................................. 12
7Module Installation ...................................................................................................15
8Connecting the Sensors to the CANbus ................................................................ 18
9Hydraulic Installation ...............................................................................................19
10Software Setup..........................................................................................................22
11Cable Drawings .........................................................................................................23
12Appendix A: Fitting Specification .......................................................................... 26

1
1Introduction
Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This
system is manufactured with top quality components and is engineered using the latest
technology to provide operating reliability unmatched for years to come.
When properly used the system can provide protection from sprayer boom damage, improve
sprayer efficiency, and ensure chemicals are applied correctly.
Please take the time to read this manual completely before attempting to install the system. A
thorough understanding of this manual will ensure that you receive the maximum benefit from
the system.
Your input can help make us better! If you find issues or have suggestions regarding the parts
list or the installation procedure, please don’t hesitate to contact us.
Every effort has been made to ensure the accuracy of the information contained in
this manual. All parts supplied are selected to specially fit the sprayer to facilitate
a complete installation. However, NORAC cannot guarantee all parts fit as
intended due to the variations of the sprayer by the manufacturer.
Please read this manual in its entirety before attempting installation.

2
2Technical Specifications
CAN ICES-3(A)/NMB-3(A)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at their
own expense.
This Class A digital apparatus complies with Canadian ICES-003.
Pursuant to EMC Directive – Article 9, this product is not intended for residential use.
Table 1: System Specifications
Supply Voltage (rated) 12VDC
Supply Current (rated) 5A
Hydraulic Pressure (maximum) 3300 psi
Baud Rate 250 kbps
Clock Frequency (maximum) 96 MHz
Solenoid Valve PWM Frequency 300 Hz
Ultrasonic Sensor Transmit Frequency 50 kHz
Operating Temperature Range 0°C to 80°C

3
3General UC5 System Layout
Figure 1 illustrates the general layout of the UC5 system components:
Figure 1: General UC5 System Layout

4
4Kit Parts
4.1 Kit Overview
Figure 2: SP01 System Parts

5
4.2 Hydraulic Plumbing
Figure 3: SP01 Hydraulic Plumbing
NOTE: AGCO supplies all hydraulic hoses and fittings.

6
4.3 List of Parts
Item NORAC Part Number AGCO Part Number Name Quantity
B10 44728 6261080M91 MOUNTING BRACKET COMPLETE UC4 BREAKAWAY EXTENDED 2
B11 44743 6261081M91 MOUNTING BRACKET MAIN LIFT SENSOR UC4 PLUS 1
C01 43220-07 6261082M91 CABLE UC5 NETWORK 14 AWG 7M 1
C03 43220-01 6261083M91 CABLE UC5 NETWORK 14 AWG 1M 2
C05 43210-15 6261083M91 CABLE UC5 NETWORK 18 AWG 15M 2
C10 43230-04 6261085M91 CABLE UC5 VALVE 2PIN DT TO 2PIN DT 4
C11 43230-09 6261086M91 CABLE UC5 VALVE 2PIN DT TO 2PIN DT TEE DIODE & RESISTOR (L
=
36"
)
3
E01 43710 6261071M1 UC5 CONTROLLER MODULE 1
E02 43720 6261072M1 UC5 VALVE MODULE 1
E04 43741 6261073M1 UC5 ROLL SENSOR VER. 2 2
E05 43750 6261074M1 UC5 ULTRASONIC SENSOR 3
E11 43765 6261077M1 UC5 NETWORK COUPLER 8-WAY 1
E12 43764 6261099M1 UC5 NETWORK COUPLER 2-WAY 1
E20 43764T 6261076M1 UC5 NETWORK COUPLER 2-WAY WITH TERMINATOR 2
F01 44928 6261089M91 ORIFICE INSERT .047 IN ONE WAY 4
M01 UC5-BC-SP01-INST 6261090M91 MANUAL INSTALLATION UC5 AGCO BRAZIL 1
M02
UC5-BC-MANUAL-ECHO-
VT
6261091M91 MANUAL UC5 OPERATORS - ECHO/VT 1
P01 106034 6261078M1 UC5 NETWORK 2 PIN PLUG 1
P03 106162 6261075M1 UC5 NETWORK 6 PIN PLUG MOLDED 2
V01 44963D 6261079M91 VALVE BLOCK ASSEMBLY 2 STATION CC/LS PROP DT 4 BOLT 1
The use of dielectric grease is not recommended on any NORAC electrical
connections.
To ensure all stainless steel hardware does not gall or seize apply a light coating of
the supplied Permatex Anti-seize grease to all threaded parts upon installation.
Permatex Anti-seize lubricant is preferred, but other similar anti-seize products
may be used.

7
5Ultrasonic Sensor Installation
5.1 Bracket Assembly
Assemble the breakaway sensor bracket as illustrated in Figure 4, following the instructions
below.
Figure 4: Breakaway Bracket Assembly
1. Compress the spring and insert it together with the collar into the base.
2. Slide the tube through the assembled part.
3. Using the bolt and nut, tighten the collar to the tube with the sensor tube centered.
4. Apply a small amount of grease to the rotating surfaces of the bracket.

8
5.2 Ultrasonic Sensor Serial Number Arrangement
When installing the UC5 sensors, start with the smallest serial number on the left-hand side,
and proceed to the largest serial number on the right hand side. Each UC5 sensor has a serial
number stamped on the sensor housing.
Apply a light coating of the supplied Permatex Anti-seize grease to all threaded
parts upon installation.
Figure 5: Sensor Serial Number Arrangement

9
5.3 Ultrasonic Sensor Mounting Guidelines
The following guidelines will ensure optimal sensor performance and prevent sensor
measurement error. These rules should be followed for both the wing sensors and the main
lift (middle) sensor.
1. In its lowest position, the sensor must be 9 inches (23 cm) or more from the ground (A).
2. The centerline of the acoustic cone should be approximately vertical at normal operating
heights (A).
3. The bottom of the sensor must be at least 9 inches in front of the spray nozzles and boom
structure (B). (This does not apply for the main lift sensor)
4. The bottom of the sensor must be at least 9 inches above the spray nozzles (C).
5. Ensure there are no other obstructions with a 12 inch (23 cm) diameter circle projected
directly below the sensor (D).
Figure 6: Sensor Mounting Guidelines

10
5.4 Wing Sensor Installation
1. The sensor bracket should be oriented forward (ahead of the boom).
2. Typically the best mounting location for the wing sensor brackets will be near the end of
the boom tips, approximately 190cm from the end.
3. Depending on the boom design, some breakaway sections will lift upwards as they break
back. If the sensor is mounted to this portion of the boom, the system will force the boom
downwards towards the ground as the boom folds backwards.
4. Mount the NORAC UC5 ultrasonic sensor into the sensor bracket and run the sensor
cable through the sensor tube.
Figure 7: Wing Sensor Mounting
A problem can arise if a sensor is not mounted correctly. It is possible for the
sensor to read off of the boom instead of the ground. This may only become
apparent once the control system is switched from soil to crop mode.
Also be careful that the sensor bracket does not collide with any other part of the
boom when the boom is folded to transport position. If possible, mount the sensor
brackets while the booms are folded to ensure they will not cause interference.
Figure 8: Sensor Reading Off Boom

11
5.5 Main Lift Sensor Installation
Figure 9: Main Lift Bracket Assembly
1. There are a variety of ways to mount the main lift bracket on most sprayers. The bracket
should position the sensor approximately in the center of the sprayer, forward of the
boom. An example of this mounting is illustrated in Figure 10.
2. Mount the ultrasonic sensor to the main lift bracket. Run the sensor cable down the center
of the main lift bracket tube.
Figure 10: Example Mounting of the Main Lift Bracket
Avoid mounting the main lift sensor over or near a wheel-track. Measurements
from the wheel-track do not provide an accurate crop height and will cause
measurement and control error.
Ensure the bracket does not collide with any other part of the sprayer throughout
the full range of main lift motion.

12
6Roll Sensor Installation
6.1 Bracket Assembly
1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine
screw and nylon lock-nuts.
2. The orientation of the mounted roll sensor to the roll sensor bracket will depend on the
bracket mounting. The roll sensor CANbus connector must be pointing towards the right
side of the sprayer.
Figure 11: Mounting Roll Sensor to Bracket
Figure 12: Roll Sensor Orientation - Connector Facing Right Wing

13
6.2 Roll Sensor Mounting Guidelines: Center Pivot Booms
1. When mounting the roll sensors, mount one to the boom frame and one to the chassis
(non-pivoting portion of the sprayer). For optimal performance, minimize the distance
between the roll sensors (A) and minimize the height from each roll sensor to the pivot
point (B).
Figure 13: Roll Sensor Mounting on a Center Pivot Suspended Boom
2. Ensure the roll sensors are relatively level when the sprayer boom and chassis are level.
3. Both roll sensor cables should be pointing towards the right hand wing of the sprayer.
4. Ensure both roll sensors are mounted adequately and that the cables provide enough slack
to allow sufficient boom roll.
5. The chassis roll sensor can also be mounted inverted to minimize the distance between the
roll sensors (Figure 14).
Figure 14: Inverted Chassis Roll Sensor Mounting on a Center Pivot Suspended Boom

14
6.3 Roll Sensor Mounting on an AGCO Sprayer
Figure 15: Roll Sensor Mounting (View from Top Rear of Sprayer)

15
7Module Installation
7.1 Control Module
An optional control module mounting bracket kit is available for purchase from NORAC.
Item Part Number Name Quantity
B20 43708 UC5 MOUNTING BRACKET KIT (CONTROL AND INPUT MODULES) 1
1. Refer to Figure 1 and Figure 16.
2. Securely mount the control module (E01) inside the module box, using screws, cable ties or
optional brackets. The module box is located on the right hand side of the sprayer, behind
the oil cooler (Figure 17).
3. Connect the AGCO CANbus to the control module Display Bus connector. This is the
end of the control module that only has one Deutsch connector.
4. Connect the power cable to one of the two CANbus connectors on the control module.
Connect the other end of the power cable to an appropriate power source. The power
must be on a keyed connection so that the NORAC modules will turn off with the key.
5. Route cable C01 from the other CANbus connector towards the rear of the sprayer.
Figure 16: Control Module Connections
Figure 17: Control Module Location

16
7.2 Valve Module
1. Install the valve module (E02) to the top of the NORAC valve block. Orient the 6-pin
Deutsch (CANbus) connectors towards the “P” and “T” ports with the label facing up.
Figure 18: Valve Module
2. Verify the valve coil connectors are oriented vertically (Figure 19).
Figure 19: Align Coils
3. Place the valve module between the valve coils. Slide a valve mounting bracket over the
connectors of the valve module and the valve coil connectors. This may require flexing the
plastic bracket slightly (Figure 20).
4. Ensure the bracket is pushed over the connectors far enough to allow the clips to engage
behind the valve connectors.
Output Numbe
r
Normal Function
1 Left Up
2 Left Down
3 Right Up
4 Right Down
5 Center Up
6 Center Down
7 SV5
8 Option 1

17
Figure 20: Valve Module Bracket Installation
5. Connect the valve module CANbus to cable C01 from the control module. Route cable
C03 from the other CANbus connector to the 8-way coupler.
6. With the valve module securely mounted to the valve block, connect the valve cables (C10),
to the valve coils. Connect cables C11 to valve module and then connect to the center up,
center down and SV5 valve. Connect center up to channel 5, center down to channel 6 and
SV5 to channel 7 (Figure 18).
7. Insert the 2-pin plug (P01) into the unused 2-pin connector on the valve module.
8. Connect the temperature probe to the valve block using the supplied 3/8” x 1/2” hex bolt.
Figure 21: Valve Module - Valve Coil Connections
Tank Port
Pressure Port
Sense Port Left Tilt Ports
Right Tilt Ports