Nordson EFD 2K Pneumatic Dispense Gun User manual

2K 600mL Dispense Guns with Built-In Retainers
Operating Manual
™
Electronic pdf les of Nordson EFD
manuals are also available at
www.nordsonefd.com

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
2
You have selected a reliable, high-quality dispensing system from Nordson EFD, the world leader in uid
dispensing. 2K dispense guns with built-in retainers were designed specically for industrial dispensing and will
provide you with years of trouble-free, productive service.
This manual will help you maximize the usefulness of your 2K dispense guns.
Please spend a few minutes to become familiar with the controls and features. Follow our recommended testing
procedures. Review the helpful information we have included, which is based on more than 50years of industrial
dispensing experience.
Most questions you will have are answered in this manual. However, if you need assistance, please do not
hesitate to contact EFD or your authorized EFD distributor. Detailed contact information is provided on the last
page of this document.
The Nordson EFD Pledge
Thank You!
You have just purchased the world’s nest precision dispensing equipment.
I want you to know that all of us at Nordson EFD value your business and will do everything in our power to
make you a satised customer.
If at any time you are not fully satised with our equipment or the support provided by your Nordson EFD
Product Application Specialist, please contact me personally at 800.556.3484 (US), 401.431.7000 (outside US),
or [email protected].
I guarantee that we will resolve any problems to your satisfaction.
Thanks again for choosing Nordson EFD.
Srini Subramanian, General Manager
Srini Subramanian

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
3
Contents........................................................................................................................................................................................ 3
Introduction ................................................................................................................................................................................... 3
Safety ............................................................................................................................................................................................ 4
Operating Features........................................................................................................................................................................ 5
Manual Dispense Gun ............................................................................................................................................................... 5
Pneumatic Dispense Gun .......................................................................................................................................................... 5
Install the Cradle-Support Handle................................................................................................................................................. 6
Connect the Air Supply (Pneumatic Guns Only) ........................................................................................................................... 6
Filling Cartridges ........................................................................................................................................................................... 6
Removing or Loading Cartridges: Manual Guns ........................................................................................................................... 7
Dispensing Material: Manual Guns................................................................................................................................................8
Removing or Loading Cartridges: Pneumatic Guns...................................................................................................................... 9
Dispensing Material: Pneumatic Guns ........................................................................................................................................ 10
Service......................................................................................................................................................................................... 11
Part Numbers .............................................................................................................................................................................. 11
Troubleshooting........................................................................................................................................................................... 11
Contents
Introduction
Manual and pneumatic 2K dispense guns with built-in aluminum retainers are used for the dispensing of lled
Film-Pak®collapsible cartridges. Manual guns are available in two thrust ratios for the dispensing of thicker
materials. Pneumatic guns include an adjustable heavy duty aluminum air regulator and an air dump valve which
stops material ow instantly.
Both manual and pneumatic guns include a spring-loaded latch system with a swing plate to securely hold
Film-Pak cartridges, a uid level indicator, and built-in aluminum cartridge retainers.
Manual dispense gun with built-in retainers Pneumatic dispense gun with built-in retainers Ported and non-ported
Film-Pak cartridges
(filled cartridges shown)

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
4
Safety
2K dispense guns are designed for heavy duty cycles over extended operating periods. Because they are
powered by compressed air, operator fatigue is minimal, but users must be aware that compressed air can be
dangerous when used incorrectly.
CAUTION
Use caution when operating a dispense gun powered by compressed air. When used incorrectly, compressed air
can cause whipping, impact, material ejection, or other related injuries.
General
• Read and understand these operating instructions before using a dispense gun.
• Compressed air can be dangerous when used incorrectly.
• Modications made by the user to the dispense gun will void the warranty and can cause personal injury.
Always:
• Use protective eye and ear equipment when operating a dispense gun.
• Wear a face mask or respirator when operating a dispense gun.
• Test the forward / reverse function before loading a cartridge.
• Disconnect the air supply before starting any service tasks.
• Ensure that cartridges are properly loaded (refer to the correct cartridge loading procedure in these instructions
for your dispense gun).
• Use a new static mixer.
• Read the material manufacturer’s instructions carefully.
• Ensure that no cross-contamination of the content of the two cartridges has occurred; material can cure in one
of the sides.
• Keep hands and ngers clear of moving parts during operation.
Do not:
• Connect the dispense gun to an air supply that can exceed 8bar (115psi).
• Immerse the dispense gun in solvent.
• Operate the dispense gun with loose, broken, or missing parts. They could come loose unexpectedly and
create a whipping / impact hazard.
• Carry the dispense gun by the air hose.
• Use damaged cartridges or the wrong type of cartridge.
• Point the dispense gun at another person.
• Disassemble the handle and adjust the safety valve inside.
• Use a static mixer that contains cured material.
• Use a partially extruded cartridge, unless using a new static mixer in which there is no cross-contamination.
• Use expired material or material that has cured.
• Continue use if you notice any abnormal noise or vibration when operating.
• Continue use if you are on unstable footing, have lost your grip, or have fallen.

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
5
Pneumatic Dispense Gun
Manual Dispense Gun
Fluid level
indicator Built-in
aluminum
retainers
Cradle-support
handle
Handle
Impact guard
Swing plate Spring-
loaded lock
Impact guard
Swing plate Spring-
loaded lock
Air input
tting
Forward / Reverse
air toggle
Fluid pressure
regulator knob
Trigger
Built-in aluminum
retainers
Fluid level
indicator
Cradle-support
handle
Operating Features

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
6
Connect the Air Supply (Pneumatic Guns Only)
1/4 NPT male thread
Cradle-support
handle
Filling Cartridges
To ll Film-Pak cartridges, refer to the lling instructions at www.nordsonefd.com/Film-PakFilling.
Install the Cradle-Support Handle
Note: The handle can be installed on the left or right side of the gun. Some guns also support bottom installation.
1 2
Manual gun Pneumatic gun
Check the plant air supply pressure. For
optimum performance the supply pressure
must be greater than 7bar (100psi) and less
than 8bar (115psi).
Note: The dispense gun will work at lower
supply pressures, but ow rates could be
reduced and may vary.
Using the supplied coupler tting, connect
clean, dry air to the 1/4 NPT male threaded air
input tting.
Air supply to the gun:
7–8bar (100–115psi)
Maximum 8bar (115psi)
Cradle-support
handle

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
7
Swing plate Spring-loaded lock
1 2
Depress the thumb release plate and pull
back on the drive rod knob to retract the drive
rods.
Release the spring-loaded lock and then open
the swing plate (loaded gun shown).
Removing or Loading Cartridges: Manual Guns
3 4
If applicable, remove spent cartridges. Slide lled Film-Pak cartridges into the
aluminum retainers.
6Attach the static mixer. If applicable, add the
retaining nut.
5Close the swing plate and engage the spring-
loaded lock.

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
8
Handle
2Squeeze the handle using normal pressure to
dispense material.
Dispensing Material: Manual Guns
Fluid level indicator
3Throughout the dispensing process, check the
uid level indicator to see how much material
remains in the cartridges.
1Purge air from the cartidge by pointing the
gun up and slowly dispensing material into the
static mixer. Then dispense the rst 15cm(6")
of unmixed material into a waste container.
Important: Before increasing the uid
pressure, verify that both material
components are travelling equally through the
mixer. As needed, dispense unmixed material
into a waste container.
Note: Perform this process for each new or
partially used cartridge.
b
a

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
9
1 2
Push the Forward / Reverse air toggle to the
REVERSE position; then pull the trigger.
Release the spring-loaded lock and then open
the swing plate (loaded gun shown).
Removing or Loading Cartridges: Pneumatic Guns
4
5
Slide lled Film-Pak cartridges into the
aluminum retainers.
Attach the static mixer. If applicable, add the
retaining nut.
6
Close the swing plate and engage the spring-
loaded lock.
3If applicable, remove spent cartridges.
Swing plate Spring-loaded lock
a b

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
10
Trigger
Fluid level indicator
Dispensing Material: Pneumatic Guns
5Pull the trigger to dispense material.
Note: This builds up a cushion of compressed
air inside the gun, which starts the ow
of material. When you release the trigger,
material ow ceases as the compressed air
escapes rapidly through a quick exhaust valve
at the rear of the gun.
6Throughout the dispensing process, check
the uid level indicator to see how much
material remains in the cartridges.
21 Place the Forward / Reverse air toggle in the
FORWARD position.
Note: The rst three steps of this procedure
will purge air from the cartridge.
Turn the uid pressure regulator knob
counterclockwise until it will no longer turn;
then turn the knob 1–2 rotations clockwise.
3Purge air from the cartidge by pointing the
gun up and slowly dispensing material into the
static mixer. Then dispense the rst 15cm(6")
of unmixed material into a waste container.
Note: Perform this process (steps 1–3) for
each new or partially used cartridge.
4Important: Before increasing the uid
pressure, verify that both material
components are travelling equally through the
mixer. As needed, dispense unmixed material
into a waste container.
Adjust the uid pressure regulator knob to the
desired setting for normal operation.
b
a

www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.
2K 600mL Dispense Guns with Built-In Retainers
11
Service
Interval Action
Daily Wipe the dispense gun using a clean rag or the material manufacturer’s
recommended solvent before any material on the gun has had time to set.
Ensure that the insides of the retainers and plungers are free of residue.
Weekly Check all external bolts and screws and tighten loose components as
required.
(Pneumatic
guns only)
Monthly
Lubricate the internal pistons and seals as follows:
1. Disconnect the air supply from the air input tting.
2. Place three (3) drops of air tool oil in the air inlet of the gun.
3. Reconnect the air supply line. When next operated, the compressed
air will blow the oil into the inner components of the gun.
Plant air
supply
coupler
tting
Air input
tting
Part # Volume Cartridge
Size Ratio Description Weight
(lb / kg)
7661494 600mL 300 x 300 1:1 Manual dispense gun with built-in retainers,
26:1 thrust ratio 5.7 / 2.6
7661495 600mL 300 x 300 1:1 Manual dispense gun with built-in retainers,
34:1 thrust ratio 5.7 / 2.6
7661613 600mL 300 x 300 1:1
Pneumatic dispense gun with built-in retainers,
499 kg at 7bar (1,100lb at 100psi) nominal
thrust
9.7 / 4.4
Troubleshooting
Problem Possible Cause Corrective Action
Air leaking from the
dispense gun handle
Air supply exceeding 8bar
(115psi), causing the safety
valve to bleed off excess air
CAUTION
Risk of equipment damage. Do not disassemble the
handle and adjust the safety valve.
1. Ensure that the air supply is lower than 8bar
(115psi).
2. Inspect cartridges for damage or leaking.
Damaged or leaking cartridges can prematurely
fail.
3. For the material being dispensed, read all of the
instructions and warnings for other possible risks.
Contact the material manufacturer for clarication
as needed.
Part Numbers
Manual dispense gun
Pneumatic dispense gun

For Nordson EFD sales and service in over
40 countries, contact Nordson EFD or go to
www.nordsonefd.com.
Global
East Providence, RI USA
800-556-3484; [phone]
[email protected]
Europe
Dunstable, Bedfordshire, UK
0800 585733; [phone]
[email protected]
Asia
China: [phone]; [email protected]
India: [phone]; [email protected]
Japan: [phone]; [email protected]
Korea: [phone]; [email protected]
SEAsia: [phone]; [email protected]
The Wave Design is a trademark of Nordson Corporation.
©2018 Nordson Corporation 7363797 v053118
NORDSON EFD ONE YEAR LIMITED WARRANTY
Nordson EFD products are warranted for one year from date of purchase to be free from
defects in material and workmanship (but not against damage caused by misuse, abrasion,
corrosion, negligence, accident, faulty installation or by dispensing material incompatible
with equipment) when the equipment is installed and operated in accordance with factory
recommendations and instructions. Nordson EFD will repair or replace free of charge any
part of the equipment thus found to be defective, on authorized return of the part prepaid to
our factory during the warranty period. In no event shall any liability or obligation of Nordson
EFD arising from this warranty exceed the purchase price of the equipment. This warranty is
valid only when oil-free, clean, dry, ltered air is used.
Nordson EFD makes no warranty of merchantability or tness for a particular purpose. In no
event shall Nordson EFD be liable for incidental or consequential damages.