Nortel Enterprise Edge CAPN Parts list manual

© 2000 Nortel Networks
P0908521 Issue 02
Enterprise Edge
CAPN
User Card

Page 1 Enterprise Edge CAPN User Card
+
The Central Answering Position (CAPN)
Why use the
CAPN? The Enterprise Edge Central Answering Position (CAPN) consists of an Enterprise Edge M7324N Telephone and one or two Enterprise Edge
CAPN modules. The CAPN allows you to:
• answer calls made from outside your Enterprise Edge system
• check the busy/not busy or Do Not Disturb status of the telephones in
your Enterprise Edge system
• transfer calls to your co-workers’ telephones
• use many more features and autodial numbers with one-touch access
What is a CAPN
module? A CAPN module is an add-on device which provides 48 extra memory or line buttons for the M7324N Telephone. A CAPN module is connected to
the side of the M7324N; a second CAPN module can be connected to the
first CAPN module. See the Enterprise Edge Central Answering Position
Installer Card for instructions on installation. When two CAPN modules
are connected to an Enterprise Edge M7324N Telephone, they provide a
total of 96 extra memory or line buttons for the M7324N Telephone.
Enterprise Edge M7324N Telephone with one CAPN module attached.
By pressing a ringing line button on your CAPN module and lifting the
handset, you can answer a call made from outside your Enterprise Edge
system. Pressing the appropriate programmed memory buttonallows you
to automatically dial an internal or external number, or use a feature.
Note:A headset may be plugged into the bottom of the M7324N
Telephone when Handsfree has been administered.

Page 2 Enterprise Edge CAPN User Card
+
Checking the pre-assigned CAPN module buttons
About pre-
assigned buttons When one or two CAPN modules are first plugged into your telephone, each CAPN module button is pre-assigned either to select a line or dial
an internal number.
If you have been assigned up to 8 lines, you can select them by pressing
the buttons in the left-hand column of your M7324N Telephone.
Remaining lines are assigned to buttons on the CAPN module(s),
beginning at the top left-hand corner of the first CAPN module and
moving down.
After lines are assigned, any remaining buttons on your CAPN module(s)
become Internal Autodial buttons, starting with the lowest default internal
number. These internal numbers can be between two and seven digits.
The numbering length is controlled in programming.
Note:In order for lines to be automatically assigned to buttons on your
CAPN module, your telephone must first be designated as a CAPN
in programming.
Checking the pre-
assigned CAPN
module buttons
1. Replace the handset.
2. Press ƒ•‚.
3. Press the buttons you want to check and read the display.
4. Ensurethatyoulabelallpre-assignedlinebuttonsandInternalAutodial
buttons correctly in the space provided beside each button.
5. Press ƒwhen you are finished.
Customising your
CAPN module You can program any of the buttons on your CAPN module that do not select lines. These buttons can be programmed to automatically dial
internal or external numbers. You can also program features onto CAPN
module buttons. If you want more line buttons programmed, see your
System Administrator.
Your CAPN module will be most effective if you use it along with the Call
Park, Transfer, Conference/Transfer, Camp-On, Message, or Voice Call
features.
Make sure that these features are programmed on your CAPN module by
following the steps presented in this card.

Page 3 Enterprise Edge CAPN User Card
+
Programming CAPN module buttons
Programming
CAPN module
buttons
Monitoring
Internal Autodial
indicators
It is important that you pay attention to the indicators beside the Internal
Autodial buttons on your CAPN module. This tells you the status of an
Enterprise Edge telephone when you answer an external call.
The status of an Enterprise Edge telephone cannot be monitored by your
CAPN module if an Internal Autodial button has not been programmed.
External Autodial
1. Replace the handset.
2. Press ƒ•⁄.
3. Press a CAPN module button.
4. Dial the external number.
5. Press OK to store the number.
6. Label your new button.
Erasing memory buttons
1. Replace the handset.
2. Press ƒ•⁄.
3. Press the memory button you
want to erase.
4. Press OK to erase the button.
Moving external line buttons
1. Replace the handset.
2. Press ƒ•⁄.
3. Press the line button that you
want to move.
4. Press the memory button on
your telephone or CAPN
module to which you want the
line moved.
5. Label your new button.
Internal Autodial
1. Replace the handset.
2. Press ƒ•¤.
3. Press a CAPN module button.
4. Dial the internal number.
5. Label your new button.
Features
1. Replace the handset.
2. Press ƒ•‹.
3. Press a CAPN module button.
4. Press ƒand the feature
code.
5. Label your new button.
An indicator appears:
• when the telephone is active
on an internal or external line
OR
• when the telephone is using
the Do Not Disturb feature
No indicator appears:
• when the telephone is idle
OR
• when the telephone is ringing
OR
• when the telephone has one
or more calls on hold, but is
not connected to any active
calls

Page 4 Enterprise Edge CAPN User Card
+
Answering and transferring a call
Answering and
transferring a call Most of the telephone calls which you deal with should involve the following procedures:
1. Answer a call made from outside the Enterprise Edge system.
2. Determine whom the call is for.
3. Check the status of the destination Enterprise Edge telephone on the
CAPN module.
4. If the indicator is OFF, transfer the call to that telephone.
OR
If the indicator is ON, use the Send Message, Ring Again on Busy, or
Camp-On feature.
Note:If your telephone has been assigned as a CAPN in programming,
you can send up to 30 messages. If your telephone has not been
assigned as a CAPN, you can send up to four messages.
Other Enterprise
Edge documents Please be sure to read your Enterprise Edge M7324N User Card and your Enterprise Edge Prime Telephone User Card (if applicable). They
contain information which should help you to use Enterprise Edge
features more effectively with your CAPN.

Page 5 Enterprise Edge CAPN User Card P0908521 Issue 02
Installation Notes
Installing the
CAPN The Enterprise Edge Station Auxiliary Power Supply is required to operate the CAPN module.
Initialising the
CAPN You must initialise each CAPN module individually during the first ten seconds after powering up to establish the default setting for the
programmable memory buttons.
Once a module is initialised, the programming is retained regardless if it
is moved or a second CAPN module is connected to it.
If the CAPN module indicators have stopped flashing, unplug the module
and then reconnect it. The indicators should turn on and flash for ten
seconds.
To initialise the CAPN module:
While the CAPN indicators are flashing, simultaneously press the two
buttons on the lower left side and the lower right side of the CAPN
module.
The indicators turn on one at a time in sequence, beginning at the lower
right corner of the module. The indicators then turn off. After all the
indicators turn off, the CAPN module is initialised and ready to use.