Norton 8000 Series User manual

3/16”
#7
1/4-20
for Wood drill 7/32
Machine Screws
#7 Drill, 1/4-20 Tap
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side
3/8 Drill other Side
(Optional)
Metal Wood
Installation Instructions
80-9380-2206-020 (04-09)
Non Hold Open Models
Sized
(Sizes 2,3,4,5,6)
8100
8300
8500
Adjustable
(Sizes 1 thru 6)
8301
8501
8000 Series Tri-Style
NOTE: For special applications a separate
door and frame preparation template is
packed with these instructions. Use this
instruction sheet for installation sequence
and closer adjustments only.
Doors should be hung on ball bearing or
anti-friction hinges.
A separate door stop is recommended.
Door and frame must be properly
reinforced.
Always adjust spring power before
adjusting control.
Adjust closing time speed between 3 and 7
seconds from 90° to 0°. Greater closing
times may be required for elderly or
handicapped.
These door closers should NOT be
installed on the exposed side (weather
side) of exterior doors.
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Right Hand Door - RH
Left Hand Reverse - LHR
Regular Arm
Installation
See Page 2
Left Hand Door - LH
Right Hand Reverse - RHR
Left Hand Door - LH
Right Hand Reverse - RHR
Top Jamb
Installation
See Page 5
Regular Arm
Installation
See Page 2
Parallel Arm
Installation
See Pages
3 & 4
Parallel Arm
Installation
See Pages
3 & 4
Optional 8500MA Series
Architectural Metal Cover
Cover Screw
Cover Screws
Standoffs
Screw Pack
Optional 8500A Series
Architectural Plastic Cover
Insert Cutouts
Cover
Insert
Standoff
Standoff
Cover Clips
Cover Screw
Cover Screws
Optional 8500M
Series Metal Cover
Backcheck Valve Power Adjustment Shaft
Latch Valve
Sweep Valve
Closer Body
Regular Arm/Top
Jamb Shoe
Connecting Rod
Forearm
Screw
Main Arm
Closer Arm
1618A Parallel
Arm Bracket
Cover
Insert
Standard 8500 Series
Full Cover
Insert Cutouts
Self Drilling Screws
Wood and Metal
For Wood drill 3/16 hole
Non Handed Door Closer
"DA" suffix (Delayed Action) is an optional
feature.
CAUTIONCAUTION
CAUTIONCAUTION
An Incorrectly installed or
improperly adjusted door closer can
cause property damage or personal
injury. These installation instructions
should be followed to avoid the
possibility of misapplication or
misadjustment.
!
NOTE: Architectural Cover
CAN NOT be used for doors
swinging over 120° using
parallel mount
Standard 8300 Series Narrow Cover
Pinion Cap (1639)
8200P Cover
8400A Cover
8400P Cover
8400MA Cover
8400M Cover
* Pilot Hole
Required
Top Jamb
Installation
See Page 5
Right Hand Door - RH
Left Hand Reverse - LHR

77
++
--
44
55
22
33
Non Hold Open Door Closers — Regular Arm
80-9380-2206-020 (04-09)
Door/Wall/Hardware/Jamb
*
conditions permitting
Right Hand Shown
Inches
(mm)
8000 Series
Pinion Cap or Optional Cover
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
5-1/2
(140)
1-3/4
(44)
12
(304.8)
1
(25.4)
A
1-3/8
(35) 3/4
(19)
Spring Power Adjust
(If Necessary)
G
For
8500 Architectural
Cover Only
HOptional
A
F
90°
E
C
L
L
Y
Y
S
S
Z
Z
R
R
B
D
or
(2)
Mark and Drill Holes
Installation Sequence
H
Optional
Optional
Covers
11
Parts
8300 Series
Screw pinion cap onto pinion shaft by
hand or with a Phillips screw driver -
DO NOT OVER TIGTHEN.
Clips for metal
covers 8500M
Latch
Sweep
++
--
++
--
66
Backcheck
Caution:
Don't completely
close valve
!
Optional 8500M
Metal Cover Installation
2 Cover
Screws
8400M Cover
2 Clips for metal
covers 8500M
— 2 —
++
--

55
33
D
4466
22
80-9380-2206-020 (04-09)
8000 Series Non Hold Open Door Closers — Parallel Arm
Door/Wall/Hardware/Jamb
*
conditions permitting.
8500A and 8500MA Series
cannot be installed
for this door opening range.
R
o
t
a
t
e
Door
Opening
To 120°
121° to 180°
*
A
9-1/2
(241)
7
(178)
B
3-3/4
(95)
1-1/4
(32)
Close Valves
Latch
Sweep
++
++
3-1/2
(89)
3/4
(19) 12
(304.8)
Top of
Door
Inches
(mm)
Frame
B
C
L
19.1
1/2
(13)
7/16
(11)
2
(51)
2-3/4
(70) 3/8
(10)
A
Remove Arm
from Spindle
Place Arm on
Spindle
— 3 —
Mark and Drill Holes
Install Closer and Bracket Preload Closer
Installation Sequence
Right Hand Shown
H
Optional
A
B
E
C
1-1/2”
F
G
Parts 11
Optional
Cover
Clips for metal
covers 8500M

1414
779988
80-9380-2206-020 (04-09)
8000 Series Non Hold Open Door Closers — Parallel Arm
1111
1010
Spring Power Adjust
(If necessary)
or
(2)
Assemble Arm
Arm Screw
Pinion Cap
or Optional Cover
LL
YY
SS
ZZ
RR
LL
YY
SS
ZZ
RR
Left Hand
Door
Right Hand
Door
or
B
A
Flat
Flat
Open Valves
Caution:
Don't remove
valves
Latch
Sweep
!
8300 Series
Screw pinion cap onto
pinion shaft by hand or
with a Phillips screw driver
- DO NOT OVER TIGHTEN.
1212
1313
Latch
Sweep
++
--
++
--
Backcheck
— 4 —
Caution:
Don't completely
close valve
++
--
!
2 Clips for metal
covers 8500M
2 Cover
Screws
Optional 8500M
Metal Cover Installation
8400M Cover
1515
1-1/2
(38)
++
--
(Use 5/16” socket or adjustable wrench
for this Adjustment)

66
33
22
Spring Power Adjust
(If Necessary)
(2)
11
19.1
8000 Series
Backcheck
Door/Wall/Hardware/Jamb
*
conditions permitting
Inches
(mm)
— 5 —
Parts
Caution:
Don't completely
close valve
A longer connecting
rod, 7701-1A, is
required for reveals
greater than 3" (76)
or
Pinion Cap
or Optional Cover
Optional
Covers
Reveal
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
Right Hand Shown
55
Latch
++
--
Non Hold Open Door Closers — Top Jamb Arm
80-9380-2206-020 (04-09)
12
(304.8)
A
3/4
(19)
1/2
(13)
5-1/2
(140)
1-7/8
(38)
1-3/4
(44) C
L
Top of
Frame
For
8500 Architectural
Cover Only
H
Optional
++
--
Installation Sequence
D
A
B
C
LL
YY
SS
ZZ
RR
E
90°
H
Optional
F
Mark and Drill Holes
!
8300 Series
Screw pinion cap onto pinion shaft
by hand or with a Phillips screw
driver - DO NOT OVER TIGHTEN.
Clips for metal
covers 8500M
A
B
E
90°
Optional
44
Sweep
++
--
8400M Cover
2 Clips for metal
covers 8500M
2 Cover
Screws
Optional 8500M
Metal Cover Installation 77
++
--

— 6 —
Arm Placement in Shoe
8000 Series
CLOSED
70°
10°
80-9380-2206-020 (04-09)
Spring Power Adjust
Adjustment Chart
(8301 & 8501 Only)
EXTERIOR
INTERIOR
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Parallel Arm
Parallel Arm
FULL 360° TURNS OF
5/16 POWER
ADJUSTMENT WRENCH
8100/8300/8500
DOOR
TYPE
OF
INST. *32”
(0.85M)
36”
(0.90M)
42”
(1.00M)
48”
(1.20M)
5811 13
7 10 13 16
710 13 16
912 15 18
20 FULL (360°) TURNS MAXIMUM AVAILABLE
*
MAXIMUM DOOR SIZE
Number of Turns Required
or
or
7-1/2 % stronger
7-1/2 % weaker
(Use 5/16” Socket or Adjustable Wrench for this Adjustment)
(Use 1/8" Hex Wrench for these Adjustments)
--
++
Backcheck
++
--
Latch
++
--
Sweep
++
--
Closer is shipped set at mid range setting = 10 turns
To identify your model:
Closer Size
Mfg.
Date
1FA
Blank = 8301/8501
2= 8302/8502
3= 8303/8503
4= 8304/8504
5 = 8305/8505
6 = 8306/8506
Adjust Closing Speed Time to between 3 to 7 seconds from 90°.
Use of the door by handicapped, elderly or small children may
require greater closing time.
!
The closing force for series 8301 & 8501 door closers is adjustable
from a size 1 to a size 6, as outlined in ANSI Standard A156.4.
When these series of door closers are installed and adjusted to
conform to ADA reduced opening force requirements (5 lbs max.) for
interior doors, they may not have adequate closing force to reliably
close and latch the door. Power adjustments charted on this page are
recommended where possible, to ensure proper door control.
By law the Americans with
Disabilities Act (ADA) may
require that door closer
installation comply with
accessability guidelines.
!
Delayed Action
(Optional)
++
--
3
++
--
Norton ® is a registered trademark of Yale Security Inc., an ASSAABLOY Group company.
Copyright © 2004, 2008 Yale Security Inc., an ASSAABLOY Group company.All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
3000 Highway 74 East • Monroe, NC 28112
Tel: • Fax: [phone]
www.nortondoorcontrols.com
(877)-974-2255
ASSA ABLO Y